Advertisement
No.
Indicator
State Description
Off: No AC power is supplied.
Steady or blinking blue: The
15
UID indicator
server is being located.
Off: The server is not being
located.
Steady green: The network port
17/18
Managem
Connection
ent
status
is properly connected.
network
indicator
Off: The network port is not
port/GE
connected.
electrical
Blinking yellow: Data is being
Data
port
transmission
transmitted.
status
Off: No data is being
indicator
transmitted.
Steady green: The data
20
10GE
Transmission
electrical
rate indicator
transmission rate is 10 Gbit/s.
port
Steady yellow: The data
transmission rate is 1 Gbit/s.
Off: The network port is not
connected.
Steady green: The network port
Connection
status
is properly connected.
indicator/Data
Blinking green: Data is being
transmission
transmitted.
status
Off: The network port is not
indicator
connected.
Steady green: The network port
23
10GE
Connection
optical
status
is properly connected.
port
indicator/Data
Blinking green: Data is being
transmission
transmitted.
status
Off: The network port is not
indicator
connected.
Steady green: The data
Transmission
rate indicator
transmission rate is 10 Gbit/s.
Steady yellow: The data
transmission rate is lower than
10 Gbit/s.
Off: The network port is not
connected.
4. Installation
Before unpacking and installing the server, wear an ESD wrist strap or gloves to avoid
damage to electrostatic-sensitive parts.
At least two people are required to move the server to the cabinet.
1. Install the server into the cabinet.
1) Place the server on the guide rails and push it into the cabinet.
2) Align the server mounting ears with the cabinet mounting bars, and tighten the captive
screws on the mounting ears.
4
Remarks
None
None
None
2. Connect cables to service and management network ports as required.
None
3. Connect the power cables.
None
None
Circuit breakers rated 32 A AC or 63 A DC are recommended.
5. Power-on
If...
The PUSs are not yet powered on
None
The server is on standby after the PSUs
are powered on
You want to power on the server
remotely
For details, see the Huawei Rack Server iBMC User Guide.
6. Error Code Reference
Error Code
Fault Description
---
The server is operating normally.
Air intake vent exceeds the operating
A00
temperature limit.
A0X
CPU X exceeds the operating temperature limit.
b01
Power supply to the mainboard is abnormal or
faulty.
b02
The RAID controller card is abnormal or faulty.
C0X
CPU X is abnormal or faulty.
E01
CMOS battery is abnormal or faulty.
F0X
Fan module X is abnormal or faulty.
HXX
Hard drive in slot XX is abnormal or faulty.
L01
A cable connection is abnormal or faulty.
P0X
PSU X is abnormal or faulty.
XXX
DIMM XXX is abnormal or faulty.
Then...
Power on the PSUs.
Press the power button on the front panel.
Run the ipmcset -d powerstate -v 1 command on
the iBMC CLI.
Click the power control button on the iBMC
WebUI.
Remarks
-
-
X: CPU number
-
-
X: CPU number
-
X: fan module number
XX: hard drive slot number
-
X: PSU number
XXX: DIMM number
5
Error Code
Fault Description
In this table, X is an integer.
7. Follow-up
After the server is successfully powered on, configure the server. For details, see the 1288H V5
Server V100R005 User Guide.
To obtain the document:
Scan the QR code.
.
Visit
Huawei technical support website
8. Hazardous Substance Statement for
Electronic and Electrical Products
Hazardous Substance
Component
Cd
Pb
Hg
◯
－
◯
Chassis
◯
－
◯
PCBA
◯
－
◯
Cables
◯
－
◯
Corollary equipment
◯
－
◯
Accessories
This table is prepared in accordance with the provisions of SJ/T 11364.
◯: indicates that the content of the hazardous substance contained in all of the homogenous
materials for the component is below the limit specified in GB/T 26572.
-: indicates that the content of the hazardous substance contained in at least one of the
homogenous materials for the component is above the limit specified in GB/T 26572.
9. FCC
Supplier's Declaration of Conformity (SDoC)
trade name: Huawei; product name: Server;
Unique Identifier:
model number:
V5,1288H V5
Responsible Party- U.S. Contact Information
Huawei Technologies USA Inc.
5700 Tennyson Parkway, Suite 500
Plano, Texas 75024
Main: 214-919-6000 / TAC Hotline: 877-448-2934
FCC Compliance Statement ( for products subject to Part 15)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
6
Remarks
Cr (VI)
PBBs
PBDEs
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
◯
H12H-05,FusionServer 1288H
Advertisement
