Related Manuals for Classic Exhibits visionary DESIGNS TF-513
Summary of Contents for Classic Exhibits visionary DESIGNS TF-513
- Page 1 © 2018 Order #XXXXX TF-513 with MOD-1329 10’ 10’ Plan View SETUP INSTRUCTIONS If you would like to tell us about your experience with your setup instructions please email us at info@classicexhibits.com...
-
Page 2: General Setup Instructions
© 2018 Order #XXXXX General Information General Setup Instructions - Read entire setup instruction manual prior to WARNING unpacking parts and pieces. - The setup instructions are created specifically for this configuration. - Setup instructions are laid out sequentially in steps, including exploded views with detailed explanation for assembly. - Page 3 © 2018 Order #XXXXX SEG Installation 1) Locate channels along the edges of extrusions Fold edges over. 2) Insert graphic corners first into channels then center point of graphic into channels. Allows for proportional fit around the perimeter of the extrusion. 3) Working from center to corner, slide silicon edge Insert into on graphic into channel.
-
Page 4: Grid View
© 2018 Order #XXXXX Grid View = 1 sq foot... - Page 5 © 2018 Order #XXXXX Case Packing Top View of Each Level 11A,12A 17,17,17A,17A Wood Counter Header & Shelf Door Plex Counter (2) Infills 13A, 16A, Base Mount Plates Plate 11 12 14 15 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7...
- Page 6 © 2018 Order #XXXXX Case Packing Case 2 of 3...
- Page 7 © 2018 Order #XXXXX Case Packing Top View of Each Level Lights Monitor Graphic Plex Counter Counter Top Floor Infills Door Mount 6,6,6A,6A 1 2 3 4 Setup Hardware 5,5,5A,5A Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Case 3 of 3...
- Page 8 © 2018 Order #XXXXX TF-513 Aero Frame Assembly Using Your Setup Instructions The Aero Setup Instructions are created specifically for your configuration. The instructions include an exploded view of the frame which is sequentially labeled. We encourage you to review the instructions before attempting to assemble your exhibit.
-
Page 9: Back View
© 2018 Order #XXXXX TF-513 Backwall Assembly Steps: 1) Connect verticals [11 to 11A] and [12 to 12A]. See Extrusion Connector detail. 2) Attach base plate [1] to vertical [11] and [1A] to vertical [12], using bolt. 3) Connect horizontals [13] and [13A] between vertical assemblies [11/11A] and [12/12A]. 4) Connect assembled Aero frame to key hole on vertical [11A] and rest on nylon insert of [1A]. - Page 10 © 2018 Order #XXXXX TF-513 Workstation Assembly Steps: 1) Attach horizontals [16] & [16A] between verticals [14] & [15]. NOTE: Install [16] at the base of door stop. Install [16A] at to top of door stop. Mount Plate Attachment 2) Attach horizontals [17] between verticals [14] & [15] Item Qty.
- Page 11 © 2018 Order #XXXXX TF-513 Attachments Steps: 1) Attach lights at desired location, on top assembled. Aero frame. See Light Attachment detail. 2) Attach monitor mount to mount plate. Monitor Mount Attachment detail. Connect light to horizontal where desired and tighten in place.
-
Page 12: Completed Assembly
© 2018 Order #XXXXX MOD-1552 Counter with MOD-1371 Steps: Item Qty. Description 1) Attach horizontals [6] between verticals [1] [2] and [3] [4]. 37.75” Vertical Extrusion w/ Door Hinges 2) Attach horizontals [5] between verticals [1] [4] and [2] [3]. 37.75”... - Page 13 © 2018 Order #XXXXX MOD-1329 iPad Stand Assembly Rotate clamshell to turn iPad from portrait Steps: to landscape orientation. 1) Attach mount plate to post, using set screw. NOTE: Mount plate must rotate to left and right before installing clamshell. 2) Attach post assembly to counter top, using bolt from under counter top.
Need help?
Do you have a question about the visionary DESIGNS TF-513 and is the answer not in the manual?
Questions and answers