Subscribe to Our Youtube Channel
Related Manuals for Midea MPPD25C
Summary of Contents for Midea MPPD25C
- Page 1 REMOTE CONTROLLER MANUAL MPPD25C IMPORTANT NOTE: MPPD30C Thank you for purchasing our air conditioner. MPPD33C Please read this manual carefully before operating your new air conditioning unit. MPPD35C Make sure to save this manual for future reference.
-
Page 3: Table Of Contents
Table of Contents Remote Controller Specifications ..........02 Handling the Remote Controller ..........03 Buttons and Functions ..............04 Remote Screen Indicators .............06 How to Use Basic Functions ............07 How to Use Advanced Functions ..........10... -
Page 4: Remote Controller Specifications
Remote Controller Specifications RG10F(B)/BGEF、RG10F1(B)/BGEF、 Model RG10F2(B1)/BGEFU1、RG10F3(B1)/BGEFU1 Rated Voltage 3.0V( Dry batteries R03/LR03×2) Signal Receiving Range -5°C~60°C(23°F~140°F) Environment Quick Start Guide AUTO COOL HEAT FIT BATTERIES SELECT MODE SELECT TEMPERATURE SELECT FAN SPEED PRESS POWER BUTTON POINT REMOTE TOWARD UNIT NOT SURE WHAT A FUNCTION DOES? How to Use Advanced Functions Refer to the How to Use Basic Functions and sections of this... -
Page 5: Handling The Remote Controller
Handling the Remote Controller Inserting and Replacing Batteries NOTES FOR USING REM OTE CONTROL Your air conditioning unit may come with two The device could comply with the local batteries(some units). Put the batteries in the national regulations. remote control before use. In Canada, it should comply with 1. -
Page 6: Buttons And Functions
Buttons and Funcitons Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how How to Use Basic Functions to operate your air conditioner, refer to the section of this manual. - Page 7 ON/OFF MODE Turns the unit on or off. Scrolls through operation modes COOL AUTO as follows: TEMP HEAT Increases temperate in 1°C (1°F) increments. NOTE: Please do not select Max. temperature is HEAT mode if the machine you 30°C (86°F ). purchased is cooling only type.
-
Page 8: Remote Screen Indicators
Remote Screen Indicators Information are displayed when the remote controller is power up. Fresh feature display(some units) (No displays when Fresh feature is activated) Sleep mode display Follow me feature display Wireless control feature display Transmission Indicator Low battery detection display(If flashes) Lights up when remote sends signal to indoor M ODE... -
Page 9: How To Use Basic Functions
How to Use Basic Functions Basic operation COOL M ode ATTENTION! Before operation, please ensure the unit is plugged in and pow er is available. SETTING TEM PERATURE The operating temperature range for units is 17°C-30°C (62°F-86°F). You can increase or decrease the set temperature in 1°C (1°F) increments. - Page 10 DRY M ode (dehumidifying) Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH. Press the ON/ OFF button to start the unit. NOTE: You can’t set temperature in mode. As a result, your remote control’s screen will not display temperature.
- Page 11 Setting the TIM ER TIM ER ON/ OFF - Set the amount of time after w hich the unit w ill automatically turn on/ off. TIM ER ON setting Press TIMER ON button to Press up or down button for Point remote to unit and wait initiate the ON time sequence.
-
Page 12: How To Use Advanced Functions
How to Use Advanced Functions SHORTCUT function Sw ing function Press Swing button Press SHORTCUT button The horizontal louver will swing up and Push this button when remote controller is on, downautomatically when pressing Swing the system will automatically revert back to button. - Page 13 SLEEP Function LOCK function Press SLEEP button The SLEEP function is used to decrease energy while you sleep(and don’t need the same temperature settings to stay comfortable). This function can only by activated via remote control. For the details, please see “sleep operation ” in “...
- Page 14 SET function Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm. To cancel the selected function, just perform the same procedures as above.
- Page 16 The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details. CR271-RG10F(B) 16117000A36802 2021.01.13...
Need help?
Do you have a question about the MPPD25C and is the answer not in the manual?
Questions and answers