Assembly And Adjustments; Intended Use - DeWalt D25892 Instruction Manual

ENGlIsh
will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension
to make up the total length, be sure each individual
extension contains at least the minimum wire size. The
following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The lower the gauge number, the
heavier the cord.
Voltage
Total length of cord in meters (m)
(Volts)
120–127V 0–7
220–240V 0–15
Rated Minimal cross-sectional area of the
ampere cord in meters (mm
Range
0–6A 1,0
6–10A 1,0
10–12A 1,5
12–16A 2,5
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

Your heavy-duty chipping hammer is designed for
professional concrete chiseling applications.
20
7–15 15–30 30–50
15–30 30–60 60–100
)
2
1,5 1,5 2,5
1,5 2,5 4,0
1,5 2,5 4,0
4,0 Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n ........................ no load speed
o
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
WALT tools are factory tested;
e
Do NoT use under wet conditions or in presence of
flammable liquids or gases.
Your heavy-duty chipping hammer is a professional
power tool. Do NoT let children come into contact with the
tool. Supervision is required when inexperienced operators
use this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Bail/Loop Style Auxiliary Handle (Fig. B)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the bail/loop style
auxiliary handle properly installed. Failure to do so
may result in the bail/loop style auxiliary handle
slipping during tool operation and subsequent
loss of control. Hold tool with both hands to
maximize control.
The bail/loop style auxiliary handle
the gear case and may be rotated 360˚ to permit right- or
left-hand use.
Mounting the Bail/Loop Style Auxiliary
Handle (Fig. B)
1. Widen the ring opening
auxiliary handle by rotating the screw for handle
2
mounting 10 counter clockwise.
2. Slide the assembly onto the nose of the tool, through
the steel ring 11 and onto the collar
holder and sleeve.
3. Rotate the bail/loop style auxiliary handle to the
desired position.
4. Lock the bail/loop style auxiliary handle in place by
securely tightening the screw for handle mounting
rotating it clockwise so that the assembly will not rotate.
Fig. B
11
10
Chisels and Chisel Holder

WARNING: Burn Hazard. ALWAYS wear gloves when
changing chisels. Accessible metal parts on the tool
and chisels may get extremely hot during operation.
2 clamps to the front of
of the bail/loop style
11
3 , past the chisel
10
3
2