Table of Contents
Advertisement
Available languages
Available languages
Quick Links
SELECT MODE
AIR OR
AIR + SEALANT
DIAL GAUGE
Measures PSI/BAR
PRESSURE RELEASE
Deflates tire
if it has too much air
ADAPTERS
VALVE
PRESTA
VALVE
DEPRESSOR*
* VALVE DEPRESSOR IS TO BE USED WITH ACCESSORY ADAPTERS (SEE PAGE 2)
Slime® provides a quick emergency repair. Treated tires should be repaired by a qualified tire
professional at the earliest opportunity to ensure safety and proper cleaning of tire pressure
sensor, if so equipped. We recommend treated tire be repaired within 3 days or 100 miles after
use of Slime Tire Sealant, whichever comes first. Advise tire professional of product use.
ATTENTION! READ ALL INSTRUCTIONS CAREFULLY
FAILURE TO FOLLOW WARNING INSTRUCTIONS CAN RESULT IN FIRE,
BALL INFLATABLES
PERSONAL INJURY OR PROPERTY DAMAGE.
REPLACEABLE SLIME SEALANT
CARTRIDGE # 10189
SEALANT/
AIR HOSE
POWER SOURCE
• Plugs into 12 volt,
15 amp power outlet
• 13.94ft. (4.25m) length
PART#50139 | REV010620ART
ON/OFF
Advertisement
Table of Contents
Related Manuals for Slime 50139
Summary of Contents for Slime 50139
- Page 1 Deflates tire if it has too much air SEALANT/ ADAPTERS POWER SOURCE AIR HOSE • Plugs into 12 volt, 15 amp power outlet • 13.94ft. (4.25m) length VALVE PRESTA BALL INFLATABLES VALVE DEPRESSOR* * VALVE DEPRESSOR IS TO BE USED WITH ACCESSORY ADAPTERS (SEE PAGE 2) Slime® provides a quick emergency repair. Treated tires should be repaired by a qualified tire professional at the earliest opportunity to ensure safety and proper cleaning of tire pressure sensor, if so equipped. We recommend treated tire be repaired within 3 days or 100 miles after use of Slime Tire Sealant, whichever comes first. Advise tire professional of product use. ATTENTION! READ ALL INSTRUCTIONS CAREFULLY FAILURE TO FOLLOW WARNING INSTRUCTIONS CAN RESULT IN FIRE, PERSONAL INJURY OR PROPERTY DAMAGE. PART#50139 | REV010620ART...
- Page 2 CAUTION: HOT • DO NOT HOLD IN HAND WHILE OPERATING • PLACE INFLATOR ON A HARD, CLEAN SURFACE. 1. DO NOT run vehicle while inflator is operating. You may need to be in “accessory” or “on” position. Please make sure emergency brake is set and car is in park. Always ensure the valve connector is fully seated to depress the core of the valve stem for proper inflation. 2. DO NOT use inflator continuously for more than 15 minutes. Allow unit to cool approximately 25 minutes between uses. Do not leave inflator unattended.
- Page 3 Screw air/sealant hose onto tire’s valve stem. Plug inflator into 12 volt accessory power outlet. Do not run vehicle while inflator is operating. You may need to be in “accessory” or “on” position. Please make sure emergency brake is set and car is in park. Push green button to turn system on. Gauge pressure will initially be high until the sealant bottle is emptied. Once bottle is empty the gauge pressure will drop and tire inflation begins. Fill to desired pressure. Turn system off and check tire pressure. Once correct tire pressure has been achieved, disconnect air hose and power plug. Drive two miles with speeds less than 25 miles per hour to disperse sealant throughout the tire, allowing it to seek out and seal the puncture. Recheck tire pressure to verify that the puncture has been sealed. At your earliest opportunity take your vehicle to a tire repair facility for a permanent professional repair. Inform tire repair specialist that Slime Sealant is in the tire. PRESSURE RELEASE The PRESSURE RELEASE ensures optimum PSI pressure. Push the area to deflate the tire if it has been overinflated, or if there is too much air prior to inflation. Check your gauge for the desired PSI level. NOTE: Correct tire pressure can be found in your vehicle’s owner’s manual or driver side doorjamb. SEALANT CARTRIDGE REMOVAL INSTRUCTIONS: Unwrap Lift off cartridge Rotate cartridge Pull cartridge out air/sealant hose. cover. to upright position.
- Page 4 Customer’s sole remedy under any warranty claim is limited to a Manufacturer’s coupon for a replacement product upon return of unit and proof of purchase. QUESTIONS OR COMMENTS: Call 1-888-457-5463 or visit www.slime.com ITW Global Tire Repair • 125 Venture Drive, Suite 210, San Luis Obispo, CA 93401 USA Slime is a trademark of Illinois Tool Works, Inc., registered in the U.S.
- Page 5 CARTUCHO REEMPLAZABLE DE BOTÓN DE SELLADOR SLIME Parte No. 10189 ENCENDIDO SELECCIONE EL MODO AIRE O AIRE Y SELLADOR MEDIDOR DE CUADRANTE Mide PSI/BAR DESCARGA DE PRESIÓN Desinfla la llanta si tiene demasiado aire MANGUERA DE ADAPTADORES FUENTE DE ENERGÍA AIRE/SELLADOR • Se conecta en una toma de corriente de 12 V • 13.94ft. (4.25m) de largo DEPRESOR DE VÁLVULA PELOTA ARTÍCULOS...
- Page 6 PRECAUCIÓN: CALIENTE • NO SOSTENGA CON LA MANO AL OPERAR • COLOQUE EL INFLADOR SOBRE UNA SUPERFICIE FIRME Y LIMPIA. 1. NO PONGA EN MARCHA el vehículo cuando el inflador esté funcionando. Puede ser necesario tenerlo en la posición de “accesorios” o “encendido.” Asegúrese de haber puesto el freno de emergencia y de tener la palanca de cambios en la posición de estacionado “park.” Asegúrese siempre de que el conector de la válvula quede bien asentado y baje el centro del vástago de la válvula para inflar de la manera adecuada.
- Page 7 Presione el botón verde para encender el sistema. Espere 6 minutos (en temperaturas por debajo de 32˚F espere 12 minutos). Puede quedar algo de sellador en la manguera. Apague el sistema y mida la presión de la llanta. Si se necesita inflar más, lea las instrucciones “AIR ONLY.” Desconecte el sistema cuando la presión de la llanta sea la correcta. Maneje dos millas a una velocidad inferior a los 40 kilómetros (25 millas) por hora para esparcir el sellador por la llanta y permitir que encuentre y selle el pinchazo. Revise nuevamente la presión de la llanta para verificar que se selló el pinchazo. Tan pronto como pueda, lleve su vehículo a un taller para que la reparación permanente sea por un profesional. Informe al especialista en reparaciones que hay Slime dentro de la llanta. DESCARGA DE PRESIÓN La DESCARGA DE PRESIÓN asegura una presión óptima en pies por pulgada cuadrada (PSI). Oprima para desinflar la llanta si está demasiado inflada o si tiene demasiado aire antes de inflarla. Verifique el medidor para obtener el nivel deseado de PSI. NOTA: La presión adecuada para las llantas se puede encontrar en el manual del propietario o en el marco de la puerta del conductor. INSTRUCCIONES PARA REMOVER EL CARTUCHO DE SELLADOR: Desenrolle la Levante la tapa del Gire el cartucho Tire del cartucho en manguera cartucho.
- Page 8 PREGUNTAS O COMENTARIOS: Llamar al 1-888-457-5463 o visitar www.slime.com ITW Global Tire Repair • 125 Venture Drive, Suite 210, San Luis Obispo, CA 93401 USA Slime® es una marca registrada de Illinois Tool Works, Inc., registrada en Estados Unidos y en otros países.
Need help?
Do you have a question about the 50139 and is the answer not in the manual?
Questions and answers