Samsung Ubigate iBG1000 Quick Start Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Network Router
  5. Ubigate iBG1000
  6. Quick start manual

Samsung Ubigate iBG1000 Quick Start Manual

Hide thumbs Also See for Ubigate iBG1000:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Samsung Ubigate iBG1000

Summary of Contents for Samsung Ubigate iBG1000

  • Page 2 This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright. No information contained herein may be copied, translated, transcribed or duplicated for any commercial purposes or disclosed to the third party in any form without the prior written consent of SAMSUNG Electronics Co., Ltd.

  • Page 3: General User Information

    FCC REQUIREMENTS This equipment, the Ubigate iBG1000, complies with Part 68 of the FCC rules and the requirements adopted by the ATCA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: A3LIS00BiBG1000.
  • Page 4 GENERAL USER INFORMATION UNAUTHORIZED MODIFICATIONS Any changes or modifications performed on this equipment that are not expressly approved in writing by SAMSUNG ELECTRONICS, CO., LTD. could cause non-compliance with the FCC rules and void the user’s authority to operate the equipment.
  • Page 5 Ubigate iBG1000 Quick Start Guide INCIDENCE OF HARM If this equipment, the Ubigate iBG1000, causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible.
  • Page 6 SAFETY WARNING High touch current earth connection essential before making telecommunication network connection. Energy Hazard-careful treatment is needed. Every wire for communication should be larger than 26 AWG. Double pole/neutral fusing. © SAMSUNG Electronics Co., Ltd.

  • Page 7: Underwriters Laboratories

    Ubigate iBG1000 Quick Start Guide UNDERWRITERS LABORATORIES The Ubigate iBG1000 system has been tested to comply with safety standards in the United States and Canada. This system is listed with Underwriters Laboratories. The cUL Mark is separately shown on the label.
  • Page 8 3. Bare, covered, or insulated earthing conductors are acceptable. A covered or insulated conductor must have a continuous outer finish that is either green, or green with one or more yellow stripes.’ © SAMSUNG Electronics Co., Ltd.
  • Page 9 Ubigate iBG1000 Quick Start Guide Safety Instructions - Rack Mount ‘Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi- unitrack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
  • Page 10 GENERAL USER INFORMATION This page is intentionally left blank. VIII © SAMSUNG Electronics Co., Ltd.

  • Page 11: Table Of Contents

    Installing on a tabletop ................. 6 Installing on a wall................7 Connecting the Ubigate iBG1000 ............10 Connecting to the Network ..............10 Powering Up the Ubigate iBG1000 ............ 15 Initial Configuration................. 17 Changing Login Parameters............... 17 Verifying the Hardware Configuration..........23 Default Configuration .................
  • Page 12 TABLE OF CONTENTS This page is intentionally left blank. © SAMSUNG Electronics Co., Ltd.

  • Page 13: Ubigate Ibg1000 Quick Start Guide

    Ubigate iBG1000 Quick Start Guide Ubigate iBG1000 Quick Start Guide Inspecting the Ubigate iBG1000 After opening the shipping carton, remove and save all packing materials and boxes. Save the packing materials. If you need to return the product, you will need to repack the unit.

  • Page 14: Ubigate Ibg1000 Status Led

    If you discover damage or missing items, contact Technical Support: http://www.samsungnetwork.com Ubigate iBG1000 Status LED LED in the top of the Ubigate iBG1000 indicates the status of the Ubigate iBG1000’s performance and operation. Each LED’s description is shown as follows. T1/E Ethernet ©...
  • Page 15 Ubigate iBG1000 Quick Start Guide Status LED Description Indication & Description Color Solid green System is operating normally. Solid red System is not operating normally. Amber System diagnostic mode. Router is not receiving power. P0 ~ P3 Solid green T1/E1 port is operating normally.

  • Page 16: Ubigate Ibg1000 Rear Side

    Ubigate iBG1000 Quick Start Guide Ubigate iBG1000 Rear Side The Ubigate iBG1000 rear panel provides connections for networking. The Ubigate iBG1000 rear panel provides connections for two Fast Ethernet ports and four T1/E1 ports. Rear Connector Description Console Port Auxiliary Port...

  • Page 17: Safety Recommendations

    Disconnect the telecommunications lines before unplugging the main power connector. Cover Panels Do not operate the Ubigate iBG1000 with missing cover panel. The cover prevents exposure to hazardous voltages and currents inside the chassis. It is important to maintaining proper air flow through the chassis.

  • Page 18: Installing The Ubigate Ibg1000

    Ubigate iBG1000 Quick Start Guide Installing the Ubigate iBG1000 This section describes how to prepare the Ubigate iBG1000 for operation either as a tabletop or a wall-mounted unit. Installing on a tabletop Allow sufficient room at the front, rear, and side of the unit for interface cabling, power cord clearance, and adequate ventilation.

  • Page 19: Installing On A Wall

    Ubigate iBG1000 Quick Start Guide Installing on a wall This section describes how to install Ubigate iBG1000 on a wall. Mark two holes, horizontally or vertically, on a desired wall. The hole distance is about 130 mm. Make holes on the marked position with an electric drill. Make the depths and the diameters of the holes more than 33 mm and around 5.5 mm to insert the plastic anchors easily, respectively.
  • Page 20 Ubigate iBG1000 Quick Start Guide With a hammer, insert plastic anchors into the holes. Insert screws to each hole and tighten the screws with a Phillips screwdriver. Be sure to remain screws untightened about 2 mm. © SAMSUNG Electronics Co., Ltd.
  • Page 21 Ubigate iBG1000 Quick Start Guide Align the screws to the bottom holes of Ubigate iBG1000 and fix it. © SAMSUNG Electronics Co., Ltd.

  • Page 22: Connecting The Ubigate Ibg1000

    Ubigate iBG1000 Quick Start Guide Connecting the Ubigate iBG1000 Connecting to the Network This section describes how to connect the Ubigate iBG1000 to various network interfaces. Follow the procedure for the interface appropriate for your network facility environment. LAN Interface The Ubigate iBG1000 accommodates several network connections.
  • Page 23 Ubigate iBG1000 Quick Start Guide T1/E1 Interface The Ubigate iBG1000 accommodates several network connections. Use a cable with RJ-45 connectors to connect to the T1/E1 network. Insert the RJ-45 connector on one end of the cable in any of the T1/E1 ports.
  • Page 24 A terminal (VT-100 or equivalent) or workstation with terminal emulation software can be used for the operator console. Connect the console to the Ubigate iBG1000 with an RJ-45 cable. For connection to a PC running terminal emulation software, your Ubigate iBG1000 is provided with an RJ-45 to DB-9 adapter cable.
  • Page 25 Ubigate iBG1000 Quick Start Guide Auxiliary Interface (for Remote Access) The Ubigate iBG1000 and a terminal can be connected to modems and phone lines for remote access. (Use a null-modem cable at the Ubigate iBG1000 to establish a modem connection.) This configuration allows you to dial into the router from a remote location.
  • Page 26 VT-100 terminal emulation software or equivalent, and configure the software as specified for modems. A modem connected to the Console port of an Ubigate iBG1000 and set for verbose mode (configured to ‘send result codes’ or ‘echo’...

  • Page 27: Powering Up The Ubigate Ibg1000

    Ubigate iBG1000 Quick Start Guide Powering Up the Ubigate iBG1000 Ubigate iBG1000 is shipped with 24 Watt AC Power Adaptor by default. This chapter describes how to power up the Ubigate iBG1000. Use only the adapter provided with the Ubigate iBG1000. Using other adapter can result in overheating or explosion and may cause malfunction.
  • Page 28 Ensure that the Ubigate iBG1000 is connected to a power source. Then, the power LED illuminates blue. After that, the router starts a booting sequence. Upon successful boot-up, the system LED illuminates green.

  • Page 29: Initial Configuration

    The System Administrator login consists of two components: the account name and the password. The initial login name is always ‘samsung’, but you can change this to suit the needs of your facility after logging in for the first time.
  • Page 30 Access the password configuration mode Router# password The system prompts for the current user name. Type ‘samsung’, and then press Enter. The system prompts for the old password. Type ‘samsung’, and then press Enter. The system prompts for the new password.
  • Page 31 Ubigate iBG1000 Quick Start Guide Administrator Account This procedure changes the administrator login name (Level 1 access) to a user-specified name. The system default is ‘samsung’. To change the account name Access the configure mode. Router# configure term Change the account name.
  • Page 32 Ubigate iBG1000 Quick Start Guide System Host Name Use the configure hostname command to assign a host name to the Ubigate iBG1000. Once assigned, the host name becomes the command line interface (CLI) prompt name. To configure the host name...
  • Page 33 Ubigate iBG1000 Quick Start Guide To configure the date, enter the month, day, and year. For example, to set the date to April 30, 2005, enter. Router/configure# date 04 30 2005 Then enter the hours (0-23) and minutes (0-59). Router/configure# time 18 14 00...
  • Page 34 Removing Users The no user command allows the system administrator to remove configured user names from the Ubigate iBG1000. To remove a user name Type no user, followed by the user’s name. Press Enter. The specified user is removed from the system.

  • Page 35: Verifying The Hardware Configuration

    Ubigate iBG1000 Quick Start Guide Verifying the Hardware Configuration To check the current hardware configuration, enter. Router# show chassis To verify the current configuration, enter the following commands. Router# show version Router# show running-config Default Configuration To restore factory default configuration settings: Clear the contents of the system.cfg file.
  • Page 36 Ubigate iBG1000 Quick Start Guide This page is intentionally left blank. © SAMSUNG Electronics Co., Ltd.
  • Page 37 Quick Start Guide ©2008 Samsung Electronics Co., Ltd. All rights reserved. Information in this manual is proprietary to SAMSUNG Electronics Co., Ltd. No information contained here may be copied, translated, transcribed or duplicated by any form without the prior written consent of SAMSUNG.

Table of Contents