OPCOM Grow Wall3 Manual page 2

Grow Wall3
Thank you for purchasing OPCOM Farm GrowWall3, the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 180 plants capacity. Please read the quick guide carefully before setting it
up. For detailed user guide video, please visit GrowWall3 page at http://www.opcomfarm.com
A. Assembly
A1. Remove all the parts from box and check all the accessories
L5
L5
Control Box x 1
L4
L4
LED Growth Lightx5
L3
Grow Kits
L3 Seedling Tray(ST-70)
(665*175*65mm)
L2
L2
Adjustment
L1
Accessories
L1
1. EC Meter 2.pH test
x1pc paper x1pc
A2. Assemble GrowWall3
1. Assembly
1
2
the L5 grooves assembly is completed. (Fig4)
3
installed assembly B13. (Fig.5)
The side column is assembled with the main line.
4
Put LED light in the center of each layer, slide along the magnets on both sides to adjust
5
the height of LED. Three positioning heights to meet the lighting needs of
insert the ligh line linto the power interface of the side column. (Fig7.)
6
2. Water Line Set Up
The upper water pipe is passed through the hole of the L6 column, and the hose passes through
7
the hole from the upper to the lower to the L1 column. (Fig9.10)
8
the crossbeam part). (Fig8)
And a lower water pipe is arranged according to the opening hole of the planting groove.
9
Install the wall mount bracket on the top of the beam and stand up the product.(Fig12)
10
3. Electric Line Set Up
Place the motor pack in the water tank and connect the motor power line on the right (Fig13)
11
4. Other Installations
Place the planting tray corresponding to the position of the lower water pipe at
12
the opening of the planting plate （Fig14）
Add 8 gallons (90% full) of water to the water tank
13 （Fig15）
Connect the control box to the marked position and connect the main line.
14
Connect the main power supply and start the power on.(Fig18)
15
Chart I: Control Box Mode
Fuction Status Light Time(On/Off) Fuction Status Light
Auto 12H/12H Auto
ON
O N 24H/0H
LED High 18H/6H Pump High
Low 6H/18H Low
OFF 0H/24H OFF
* Most plants can be grown using the AUTO mode.
* Remote controller support wireless remote control.
* When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset
* When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset
5. LED light Control
Select your color of LED light - There is a switch in the right side of the LED light.(Fig19) You can select the color manually
16
by pressing the switch. We have white light and white-red light mode for your selection. Please note that the control box
can only control the time of LED On or LED OFF, the color of LED light need to control manually.
17 The height of LED light - You can decide the height of the LED light depending on your needs. Please note that the
the light to the plants the higher the temperature is.
Ribbon x10pc Hose x 1 Tube(1) x 4 Tube(2) x 1 Base Standx2 maple plank x6
Planting tray x5pcs Wall Mount Brackets x 2pcs Pump x 2pcs
(Backup pump x 1)
x2pcs Grow Sponge 4 x 60pk Grow Sponge 3x60pk Grow Sponge 3 x60pk
(OASP001) (OASS001 For Green Lettuce) (OASS002 For Red Leaf Lettuce)
Salt#1 250ml x2 Soda#1 50ml x1 Lemon#1 50ml x2
3. Water 4. Remote 5.Cleaning s 6. Screwdriver Cross- 7.Filter
Spray x1pc Controller x 1pc ponge x1pc Head x1pc Spongex10pc
(Fig14)
(Fig5)
(Fig6.)
(Fig4)
(Fig11)
（Fig11）
(Fig3)
(Fig2)
1
(Fig1)
（Fig16.17）
Time(On/Off)
(Fig9) (Fig10) (Fig15)
12 cycles/day ( 30 mins/cycle )
24 cycles/day ( 30 mins/cycle )
4 cycles/day ( 30 mins/cycle )
2 cycle/day
( 30 mins/cycle )
0 cycle/day
power on timeline.
power off timeline.
8 gallons （30L）
closer
Please read and follow every steps to avoid any malfunction.
B. Seedling
B1. Germination Stage
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)
3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray
(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and
ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
4. Place the seedling tray with cover in the shade.(Fig3)
5. Suggest using Watering Spray water to sponges and keep them wet everyday.
sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.
7. Discard unsprouted sponges after regular germination time.
8. In each sponge, keep strong plants and cut the other weak plants.
Expansion Anchor Bolts x4pcs
Wall-Mount Screws x4pcs
Chart II: Plant Stage
Grow Sponge 3x60pk
Basil, Lemon Balm
(OASS006 For Basil)
Germination Stage
Young Plant Stage
Growing Stage
* Please keep the seeds in refrigerator if you don't use it, recommended temperture is 41
Manual
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
Warranty Card Quick Guide Manual * If you need more planting information, please vist to www.opcomfarm.com and read "Plant Q&A".
Grow Wall3
Hydroponics Green Wall3
Quick Guide Manual
A spoon=1g / B spoon=5g / C spoon=10g
Status
(Fig12)
Salt#1
(Fig7)
(Fig6) A spoon=1g / B spoon=5g / C spoon=10g
4.0-4.5
Satus
(Fig17)
Add Bx0.5
Soda#1
Lemon#1
B3. Growing Stage
(Fig16)
plants grow to over 2 inches height, switch control n e h
2. After 4-6 weeks, harvest the larger plants for consumption and keep smaller plants growing.
1
(Fig8)
3. For time saving, sow the new seeds in sprout tray one week before you start next planting process.
C. Sprouts and Microgreens.
Before you start next seedling, take advantage of the seedling tray f
(Fig19)
2. Put seeds in warm water(recommeded temperature is 95
3. Cover the sponges with wet paper towels.
4. Place the seedling tray with cover in the shade or cover it with black
5. After germination, during the growing stage, keep green sprout under the light and white sprout in the shade or cover it
with black cloth; in 7-10 days, you can harvest.
(Fig13) (Fig18)
Planting Time LED Mode Pump Mode Nourishment T
( )
Day 0~7 N/A N/A N/A 68 - 77
Day 3~1 4 ON ON NT-Starter 59 - 86 45%-70%
After Day 1 4 Auto Auto NT-Adjuster 59 - 86 45%-70%
-
50.
0.0-0.5 0.5-1.0 1.0-1.5 over 2.0
Add Ax2 Add Ax1 Standard range Add water
4.5-5.0 5.0-5.5 5.5-6.5 6.5-7.0
Add Ax2 Add Ax1 Standard range
Standard range Add Bx0.5
W . 1 box to auto mode. Please refer to Chart II
, not over 104 F) for 24 hours.
Day 0 Day 1
Green sprout
(Fig1）
This side up!
(Fig2）
(Fig3)
(Fig4)
RH EC pH Notes
Be sure each sponge is fully wet in
80% 0.5-1.0 5.5-6.5
seedling tray.
1.0-2.0 5.5-6.5
1.0-2.0 5.5-6.5
7.0-7.5
Add Bx1
1 week
.
Harvest
4-6 weeks
Keep
Cut off Large leaf for regrow
Day 7-10
White sprout