OPCOM Hydroponics Grow Wall3 Quick Manual Manual

Grow Wall3
Thank you for purchasing OPCOM Farm GrowWall3, the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 80 plants capacity. Read the quick guide carefully before setting it up.
For detailed user guide video, please visit GrowWall3 page at http://www.opcomfarm.com/Growwall3
A. Assembly
A1. Remove all the parts from box and check all the accessories
L5
L5
Control Box x 1
L4
L4
LED Growth Lightx5
L3
Grow Kits
L3
Seedling Tray(ST-70)
(665*175*65mm)
L2
L2
NT-Starter 40gx3pcs
L1 (OANT006 for 40L)
L1
Accessories
1. EC & pH 2. Water Spray x1pc
Meter x1pc
A2. Assemble GrowWall3
1. Assembly
The side column parts are assemble fixed to the L1 water tank.(Fig1.2)
1
L2 fixed with L3 water tank,follow this step until finish L5 assembly.(Fig3)
2
Fixed L5 side column parts with beam.(Fig4)
3
The beam parts is fixed in the lifting rod head and the lamp head lifting assembly,
4
then can move the tape and the lifting rod fixing piece is stuck in the lifting rod
fixing piece. (Fig5 .6 .7)
Assembly cable from side column, and DC connector fixed with screw cap.(Fig8.9)
5
2. Water Line Set Up
Connect the hose to the pump, move through the hole on the left side of the tank to
6
the slot on the right, and move upward from the lower layer to layer L5.(Fig10.11)
3. Electric Line Set Up
Insert three pieces of maple plank from the side column in turn. Clip the lifting
7
rod into the fixing piece, and then tighten the lifting trigger of the third column
on the right with the screw.(Fig12.13)
LED lamp head stuck in each layer of lifting corresponding hole.(Fig14.15 )
8
4. Other Installations
Insert the L1, L3, L5 rigid water pipe on the right into the slot on the right, insert the
9
rigid water pipe into the L2 and L4 layer on the left according to the same steps, and
then put the water pipe into the water tank.(Fig16.17 )
Amounting the wall mount holder in screw hole at the top of the cross member.
(Fig18.19 )
Add 8 gallons (90% full) of water to the tank.(Fig20 )
11
Attach the control box to the marked position and insert the pump power supply.(Fig21.22)
12
Connect the main power supply and start the switch.(Fig23.24)
13
Chart I: Control Box Mode
Fuction Status Light Time(On/Off) Fuction Status
Auto 12H/12H Auto
O N 24H/0H ON
LED High 18H/6H Pump High
Low 6H/18H Low
OFF 0H/24H OFF
* Most plants can de grown using the AUTO mode.
* a. When Power On, press hold POWER button until 1 beep sound (Less than 2 second) to turn off the power.
b.When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset timeline to auto power on
(On/Off 16H/8H).
* a.When Power Off, press hold POWER button until 1 beep sound (Less than 2 second) to turn off the power.
b.When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset timeline to auto power off
(On/Off 8H/16H).
Ribbon x10pc Hose x 1 Tube(1) x 4 Tube(2) x 1 Base Standx2
Planting tray x5pcs Wall Mount Brackets x 2pcs Pump x 2pcs
(Backup pump x 1)
x2pcs Grow Sponge 4 x 60pk Grow Sponge 3x60pk Grow Sponge 3 x60pk
(OASP001) (OASS001 For Green Lettuce) (OASS002 For Red Leaf Lettuce)
NT-Adjuster 20gx15pcs
pH+ 2.2gx15pcs
(OANT008 for 40L)
3. Remote Controller x 1pc 4.Cleaning s 5. Screwdriver Cross-
Head x1pc
ponge x1pc
(Fig6) (Fig7)
(Fig5)
(Fig4)
(Fig17)
(Fig16)
(Fig3)
2
(Fig2)
1
(Fig1)
(Fig10) (Fig11)
1
Light Time(On/Off)
12 cycles/day ( 30 mins/cycle )
24 cycles/day ( 30 mins/cycle )
4 cycles/day
( 30 mins/cycle )
2 cycle/day
( 30 mins/cycle )
0 cycle/day
9
8 gallons （30L）
Please read and follow every steps to avoid any malfunction.
B. Seedling
B1. Sprout Stage
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)
3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray
(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and
ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
4. Place the seedling tray with cover in the shade.(Fig3)
5. Suggest use watering can spray water to sponges and keep them wet everyday.
6. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and move them into product (make
maple plank x6 Lifting rod x6
sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.
7. Discard unsprouted sponges after regular germination time.
* Different plant may have different germination time, please check before plant.
Expansion Anchor Bolts x4pcs
Wall-Mount Screws x4pcs
Chart II: Plant Stage
Basil, Lemon Balm
Grow Sponge 3x60pk
(OASS006 For Basil)
Sprout Stage
Young Plant Stage
pH- 6gx15pcs
Growing Stage
* Please keep the seeds in refrigerator if you don't use it, recommended temperture is 41
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
Manual
* If you need more planting information, please vist to www.opcomfarm.com and read "Plant Q&A".
Warranty Card Quick Guide Manual
Grow Wall3
Hydroponics Green Wall3
Quick Guide Manual
(Fig18) (Fig19)
Status
NT-Adjuster
(Fig14)
(Fig15)
Satus
(Fig21)
pH+
pH-
(Fig22)
B3. Growing Stage
p a l n s t
. 1 W h e n
1
2. After 4-6 weeks, harvest the larger plants for consumption and keep smaller plants growing.
(Fig12)
3. For time saving, sow the new seeds in sprout tray one week before you start next planting process.
(Fig13)
C. Sprouts and Microgreens.
1. Before you start next seedling, take advantage of the seedling tray for sprouts and microgreens it takes 7-10 days to harvest.
(Fig8)
2. Put seeds in warm water(recommeded temperature is 95
3. Cover the sponges with wet paper towels.
(Fig9)
4. Place the seedling tray with cover in the shade or cover it with black cloth.
5. After germination, during the growing stage, keep green sprout under the light and white sprout in the shade or cover it
with black cloth; in 7-10 days, you can harvest.
(Fig20) (Fig23) (Fig24)
Planting Time LED Mode Pump Mode Nourishment T
( )
Day 0~7 N/A N/A N/A 68 - 77
59 - 86
Day 3~14 ON ON NT-Starter
After Day 14 Auto Auto NT-Adjuster 59 - 86
50.
-
0.0-0.5 0.5-1.0 1.0-1.5
(Add 2pc) (Add 1pc) Standard range
4.0-4.5 4.5-5.0 5.0-5.5 5.5-6.5 6.5-7.0
Add 3pc Add 2pc Add 1pc Standard range
Standard range Add 1pc
g o r w o t o v r e 2 n i h c s e h e g i t h s , w t i h c o c n r t l o box to auto mode. Please refer to Chart II.
F , not over 104 ) for 24 hours.
Day 0 Day 1
(Fig1）
This side up!
(Fig2）
(Fig3)
(Fig4)
RH EC pH Notes
Be sure each sponge is fully wet in
80% 0.5-1.0 5.5-6.5
seedling tray.
45%-70% 1.0-2.0 5.5-6.5
45%-70% 1.0-2.0 5.5-6.5
Plant Size Small
Sponge Number 175
Planting number 123 (70%)
How to Set up x 5 Layer
over 2.0
Plant Size Medium-Large
Add water
Sponge Number 88
Planting number 62 (70%)
How to Set up x 5 Layer
7.0-7.5
Add 2pc
1 week
Harvest
4-6 weeks
Keep
Cut off Large leaf for regrow
F
Day 7-10
Green sprout White sprout