Operation - Campbell Hausfeld PW2575 Product Manual

Lavadoras a Presión
Hidrolavadora de Eje Vertical
1
21
20
2
19
4
3
5
12
13
11
7
10
6
8
9
Para ordenar repuestos, sírvase lla-
mar al 1-800-330-0712 (En los
Estados Unidos, o llame a su dis-
tribuidor local)
Sírvase darnos la siguiente información:
- Número del modelo
- Número de série (de haberlo)
- Descripción y número del repuesto según la lista de repuestos
Puede escribirnos a:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030
16
17
No. Número
14
de Descripción del
Ref. repuesto
1 Tubo del mango PM343715AV
2 * Perno de 6,4 mm (1/4") - 20 (mango) PM001903AV
3 * Arandela plana PM002000AV
4 * Tuerca de seguridad de nilon de
6,4 mm (1/4") - 20 ST073808AV
5 * Perno de 6,4 mm (1/4") - 20 (base) PM001902AV
6 Pata izquierda PM344828BH
7 Pata derecha PM345100BH
8 Defensa de caucho AL062300AV
9 * Tornillo autorrosc. 0,64 cm (1/4")
- 20 x 19,1 mm (3/4") MJ102100AV
10 Rueda WA120100AV
11 Tuerca de presión AL066300AV
12 * Perno de 6,4 mm (1/4") - 20 (Eje) PM001904AV
13 Eje PM344831BH
14 Placa de base GN004530AV
15 Tubo del detergente (not shown) PM013800AV
16 Pistola PM243000AV
17 Anillo en O (pistola) PM245800SV
18 Manguera PM344301AV
19 Lanza turbo (optional) PM243500AV
20 Lanza alta presión PM268500AV
21 Tanque de detergente PM268680AJ
22 Replacement Pump PM341000SJ
* Artículo disponible en ferreterías locales.
28 Sp
Pressure Washers
Pre-Operation (Continued)
7. Attach the lance with nozzle to the gun
(see Figure 7).
TRIGGER SAFETY LATCH
In the engaged position, the trigger
18
safety latch prevents the gun from being
triggered accidentally. Push the latch fully
down to engage it (See Figure 8 and 9).
Always engage the trigger safety latch
when the unit is not in use.

Operation

1. Surface Preparation
Ctd.
The following cleaning procedure will
help you organize your cleaning task
and ensures that you will achieve the
1
best results in the shortest amount of
2
14
time. Remember to use the spraying /
cleaning techniques mentioned in the
7
following section.
3
1 Before starting a pressure washer
1
cleaning job, prepare the surface you
2
intend to clean. Clear furniture from
the area and make sure that all
2
windows and doors are closed tightly.
2
Also, protect all plants and trees near
2
2
the cleaning area with a drop cloth. A
1
covering ensures that your plants won't
1
be sprayed by the detergents.
1
1
1
2. Start Up
1
1
ALWAYS use the following start up
1
procedure to ensure that the unit is
1
1 started safely and properly.
If water has frozen
in the pressure
washer, thaw the pressure washer in a
warm room before starting. DO NOT
pour hot water on or into the pump;
internal parts will be damaged.
1. Check engine oil levels. Add oil as
necessary.
2. Check fuel level. Add unleaded
gasoline (rated 86 octane or higher)
as required
Figure 7– Attach lance to gun
Engaged
Figure 8 - Trigger locked Figure 9 - Trigger unlocked
DO NOT refuel a hot moving the choke ring fully to the
engine. Refueling a
right. Turn the ignition switch to
hot engine could cause a fire. Use only
"ON".
fresh, clean regular or unleaded
7. Start the engine. Unlock the
gasoline. Close the fuel shutoff valve
during refueling.
trigger safety latch on the gun (See
Figure 9). Grasp the starter rope
3. Attach a garden hose to the inlet side
and brace one foot on the chassis.
of the pump and connect it to the
Point the gun in a safe direction.
water supply. Use a hose with an
While squeezing the trigger on the
internal diameter (I.D.) of 5/8 inch (1.58
gun, pull the starter rope rapidly
cm) and a length of 50 ft. (15 m) or less.
and firmly (See Figure 10).
Some local
Continue holding the rope as it
plumbing codes
require backflow prevention when
returns. Repeat these steps until
connecting to a fresh water supply.
the engine starts.
Install a backflow preventer upstream
from the pump if necessary.
a. If inlet water pressure is over 100
psi, install a regulating water valve
at the garden hose connection.
b. Do not exceed 100˚ F (38˚ C) inlet
water temperature.
NOTE: The inlet water supply must have a
minimum flow rate of 5 gpm (19 lpm).
4. Turn the water supply ON.
Never run the unit
dry. Be sure the
water supply is completely turned on
before operating the unit.
5. Trigger the gun until water sprays
smoothly from the tip indicating
that all air is purged from the
system. Lock the trigger safety latch.
6. Open the fuel valve by turning the
knob counterclockwise until it stops.
Figure 10 - Start the engine
Close the choke (if engine is cold) by
5
Disengaged
www.chpower.com