Campbell Hausfeld PW2575 Product Manual page 6

Pressure Washers
Operation (Continued)
When pulling the
starter rope, make
sure to keep your hand and arm clear
of the engine and cart components.
Never let the starter
rope return by itself.
Doing so could jam the recoil system.
8. If the engine does not start after two
or three pulls or if the rope is hard to
pull, squeeze the gun trigger to
Figure 12 - Narrow high impact stream
release the pressure that has built up
in the high pressure hose. Repeat
Steps 7 and 8 until the engine starts.
3. Initial High Pressure Rinse
Spray the cleaning surface with water to
clear off any dirt or grime that may have
collected on the surface. Doing so allows
the detergent to attack the deep down
dirt that has worked its way into the
cleaning surface. Before triggering the
Figure 13 - Wide fan pattern
gun, adjust the nozzle to a wide fan
pattern and slowly adjust it to the desired
ANGLE TO THE CLEANING SURFACE
spray pattern. Using a wide fan pattern
When spraying water against a surface,
helps you avoid applying too much
you can generate maximum impact by
concentrated spray to the surface which
striking the surface head on. However,
can cause damage.
this type of impact can cause dirt
ADJUSTING FAN PATTERN
particles to embed in the surface and
Adjust the angle of spray coming out of
can prevent the desired cleaning action.
the lance by rotating the nozzle. The
The optimum angle for spraying water
spray pattern will vary from a 0˚ narrow
against a cleaning surface is 45 degrees.
high impact stream to a 60˚ wide fan
Spray water against a surface at a 45
spray (See Figure 11 ).
degree angle to achieve the most
beneficial impact force and to efficiently
remove debris.
Nozzle
Figure 11 - Adjusting nozzle for fan
pattern
A narrow stream has high impact force
on the cleaning surface and results in
maximum deep cleaning in a
concentrated area. However, this
Figure 14 - Optimum angle to cleaning
narrow high impact spray can damage
surface
some surfaces so use it cautiously.
DISTANCE FROM CLEANING SURFACE
A wide fan pattern will distribute the
The distance between the spray nozzle
impact of the water over a larger area
and the cleaning surface is another
resulting in excellent cleaning action
factor that affects the impact force of
with a reduced risk of surface damage.
the water. The impact force of the water
Clean large surface areas quickly using
increases as the nozzle is moved closer to
a wide fan pattern.
the surface.
www.chpower.com
HOW TO AVOID DAMAGING SURFACES
Damage to cleaning surfaces occurs
because the impact force of the water
exceeds the durability of the surface.
You can vary the impact force by
controlling the nozzle's fan pattern,
the nozzle's angle to the cleaning
surface, and the nozzle's distance from
the cleaning surface. Never use a
narrow high impact stream or a
Turbo/rotary nozzle on a surface that is
susceptible to damage. Avoid spraying
windows with a narrow high impact
stream or turbo nozzle. Doing so may
break the window. The most sure way
to avoid damaging surfaces is to follow
these steps:
1. Before triggering the gun, adjust the
nozzle to a wide fan pattern.
2. Place the nozzle approximately 4-5
feet away from the cleaning
surface. Then hold the nozzle at a
45 degree angle to the cleaning
surface. Trigger the gun.
3. Vary the fan pattern spray angle
and the distance to the cleaning
surface until optimum cleaning
efficiency is achieved without
damaging the surface.
TURBO LANCE (NOT INCLUDED WITH
ALL MODELS)
A turbo lance is equipped with a
permanently attached nozzle . This
nozzle, sometimes referred to as a
rotary nozzle, can significantly reduce
cleaning time. The turbo nozzle
combines the power of a narrow high
impact stream with the efficiency of a
25 degree fan pattern. The turbo
nozzle swirls a narrow high impact
stream into a cone shape to clean a
larger area.
Since a turbo nozzle
uses a narrow high
impact stream, only use a turbo lance in
applications where the cleaning surface
cannot be damaged by narrow high
impact spray. The turbo nozzle is NOT
adjustable and cannot be used to apply
detergent.
6
Lavadoras a Presión
Bombas
38*
4
1
3
2
6
Para ordenar repuestos, sírvase lla-
mar al 1-800-330-0712 (En los Estados
Unidos, o llame a su distribuidor
local)
Puede escribirnos a:
Campbell Hausfeld
Sirvase darnos la siguiente información:
Attn: Customer Service
- Número del Modelo
100 Production Drive
- Número de serie (de haberlo)
Harrison, OH 45030 - Descripción y número del repuesto según la lista
No. de Número del
Descripción
Ref. repuesto
I
-1 Anillo para el polvo
I
2 Cubierta de la bomba
I
3 Anillo para sellar el sistema de lubricación
I
4 Cojinete
I
5 Placa oscilante
6 Valvula de relieve térmico PM005405SV
G
7 Ensamble del cuerpo de la válvula de descarga
G
8 Ensamble de la guía del cuerpo
G
9 Ensamble del cuerpo de la válvula de retención
G
10 Resorte de la válvula de retención
11 Tornillo PM007500SV
N
12 Sello del sistema de lubricación
M
13 Separador del anillo del sistema de lubricación
M
14 Anillo para sellar el asiento
M
15 Anillo anti-extrusión
L
16 Anillo para sellar el agua
L L I I
17 Anillo en o
L L
18 Válvula de succión
19 Perno de la culata PM025100AV
20 Culata, 12 mm PM255240SV
JUEGOS DE PIEZAS PARA EL SERVICIO
ESPECIFICACIONES DE TORQUES
I Ensamblaje de la cubierta (Incluye 1 de c/u de las piezas #1-5)
(kg-cm)
G Ensamblaje del descargador (Incluye 1 de c/u de las piezas #7-10 y 26)
N Juego de anillos para sellar el sistema de lubricación (Incluye 3 piezas #12)
Ref. No. Descripción Torque M Juego de la guía del pistón (Incluye 3 de c/u de las piezas #13-15)
L Juego de anillos para sellar el agua (Incluye 3 piezas #16)
# Juego de válvulas de entrada (Incluye 3 piezas #17 y 18)
6 Valvula de relieve
L L
Juego de válvulas de salida (Incluye 3 piezas #21 y 22)
térmico 126,8 N N
Juego de tapas de válvulas (Incluye 3 piezas #23)
I I
11 Tornillo 110,7 Juego de anillos en o (Incluye 3 piezas #17 y 21 y 1 de c/u de las piezas #25 y 33) PM058000SV
G G
Juego de inyector de detergentes (Incluye 1 de c/u de las piezas #27-29)
19 Perno de la culata 110,7
M M
Juego de pistónes (Incluye 3 piezas #32 y 34)
23 Tapa de la válvula 276,7
# #
Juego de cojinetes de aguja (Incluye 1 de c/u de las piezas #35-37)
PM341000SJ
29
10
36 9
26
28
5 27
23
37
35
33 30
31
34
25
24
8
32
17
7
13 16
12 15
11
39 14
No. de Número del
Ctd. Descripción
Ref. repuesto
– 21 Anillo en o
– 22 Ensamblaje de la válvula de salida
23 Tapa de la válvula
–
24 Tapón PM064301SV
–
25 Anillo en o
– PM041870SV
26 G Ensamble del inyector de productos químicos PM341015SV
1
– 27 Resorte
– 28 Bola
– 29 Anillo en o y conector de mangueras
1 30 Tornillo PM064302SV
2 31 Cuerpo del pistón PM341020SV
– 32 Resorte del pistón
– 33 Anillo en o, 85 x 2.5
– 34 Pistón
35 Zapata de presión
–
36 Cojinete de agujas
–
– 37 Disco de cojinetes
– 38* Perno MJ101211AV
4 39 Ensamble de pivote de bronce PM041360SJ
1 Notas
* Se venden por separado
Capacidad de Aceite: 118 mL
Tipo de Aceite: SAE 30W (sin detergente)
NÚMERO DE PIEZA
PM255230SV
PM341011SJ
PM256500SV
PM344905SV
PM344910SV
PM064740SV
PM064304SV
PM064750SV
PM064305SV
PM344920SV
PM041840SV
27 Sp
22
21
20
19
18
Ctd.
#
I I
–
#
–
N N –
1
1
1
G G
–
G G
–
G G
–
1
1
M M
–
I I
–
M M
–
# #
–
# #
–
# #
–
3
1
CTD.
1
1
1
1
1
1
1
1
1
1
1
1