Canon MP970 Service Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Printer
  5. PIXMA MP970
  6. Service manual

Canon MP970 Service Manual

Hide thumbs Also See for MP970:
Table of Contents

Advertisement

Quick Links

MP970
Service Manual
Revision 0
QY8-13BP-000
COPYRIGHT©2007 CANON INC. CANON MP970 082007 XX 0.00-0
Scope
This manual has been issued by Canon Inc., to provide the service technicians of this product with the information necessary for
qualified persons to learn technical theory, installation, maintenance, and repair of products. The manual covers information
applicable in all regions where the product is sold. For this reason, it may contain information that is not applicable to your region.
This manual does not provide sufficient information for disassembly and reassembly procedures.
Refer to the graphics in the separate Parts Catalog.
Revision
This manual could include technical inaccuracies or typographical errors due to improvements or changes made to the product. When
changes are made to the contents of the manual, Canon will release technical information when necessary. When substantial changes
are made to the contents of the manual, Canon will issue a revised edition.
The following do not apply if they do not conform to the laws and regulations of the region where the manual or product is used:
Trademarks
Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders.
Copyright
All rights reserved. No parts of this manual may be reproduced in any form or by any means or translated into another language
without the written permission of Canon Inc., except in the case of internal business use.
Copyright © 2007 by Canon Inc.
CANON INC.
Inkjet Device Quality Assurance Div. 1
451, Tsukagoshi 3-chome, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8530, Japan

Advertisement

Table of Contents
loading

Related Manuals for Canon MP970

Summary of Contents for Canon MP970

  • Page 1 COPYRIGHT©2007 CANON INC. CANON MP970 082007 XX 0.00-0 Scope This manual has been issued by Canon Inc., to provide the service technicians of this product with the information necessary for qualified persons to learn technical theory, installation, maintenance, and repair of products. The manual covers information applicable in all regions where the product is sold.

  • Page 2: Table Of Contents

    MP970 TABLE OF CONTENTS 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer 1-2. Customer Maintenance 1-3. Special Tools 1-4. Serial Number Location 2. LIST OF ERROR DISPLAY / INDICATION 2-1. Operator Call Errors 2-2.

  • Page 3: Maintenance

    MP970 TABLE OF CONTENTS 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer (1) Adjustment Approx. Adjustment Timing Purpose Tool time EEPROM - At logic board replacement To initialize settings None. 1 min. initialization Perform in the service mode.
  • Page 4 Platen glass - At protection sheet To maintain scanning accuracy, None. 1 min. protection sheet replacement hold the sheet with the long side (document - At protection sheet frame down, then fit its lower right pressure plate replacement corner to the platen glass sheet) position - At scanner unit replacement reference mark (back left).

  • Page 5: Customer Maintenance

    1-2. Customer Maintenance Approx. Adjustment Timing Purpose Tool time Automatic print - At print head replacement To ensure accurate dot - Machine buttons 4 min. head alignment - When print quality is not satisfying (uneven placement. - Computer (MP printing, etc.) driver) Manual print - At print head replacement...

  • Page 6: Special Tools

    1-3. Special Tools Name Tool No. Application Remarks To the carriage shaft sliding portions, lift cam bushing, and Easy- In common with the FLOIL KG-107A QY9-0057-000 Scroll Wheel base. MP600, etc. 1-4. Serial Number Location On the carriage flexible cable holder (visible on the right of the carriage after the machine is turned on, the scanning unit is opened, and the carriage stops at the ink tank replacement position) The serial number for the scanning unit: On the right side of the unit (visible on the right side when the scanning unit is opened)

  • Page 7: List Of Error Display / Indication

    MP970 TABLE OF CONTENTS 2. LIST OF ERROR DISPLAY / INDICATION Errors and warnings are displayed by the following ways: 1. Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD in text and by icon.
  • Page 8 the same color following color is installed. (s). installed. Ink tank in a wrong [1680] U072 Some ink tanks are not installed in Install the ink tank(s) in the correct position. position. place. Warning: The ink [1700, 1701] Contact the support center or Replace the ink absorber, and reset its counter.

  • Page 9: Service Call Errors

    2-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs) Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code with the message, "Printer error has occurred. Turn off power then back on again. If problem persists, see the manual." is displayed on the LCD.

  • Page 10: Other Error Messages

    - Paper feed motor - Logic board 19 times Ink tank position sensor [6502] None of the ink tank position is detected. - Platen unit error - Logic board 22 times Scanner home position [5010] The scanner unit cannot detect the home - Scanner unit error position, or the scanner unit warming-up is...
  • Page 11 8.5"x11"(215x279). available only with A4 or Letter size paper is returns to the display before the error selected, but the paper size is not set to A4 or occurrence. Letter. Cannot specify "stickers" and "half- The selected layout on the handwriting sheet A temporary error.

  • Page 12: Warnings

    2-4. Warnings Warning Message on the LCD Solution Low ink "!" is indicated for an applicable ink tank icon in No special solution. the Status Monitor. Since the ink will be used up soon, prepare for a new ink tank. Print head temperature If the print head temperature does not fall, the When the print head temperature falls, the error is...
  • Page 13 Paper feed problems (multi-feeding, - Examine the inside to confirm that no parts are damaged, skewed feeding, no feeding). and the rollers are clean. - Remove foreign material. - Adjust the paper guide properly. - Set the paper properly. - Confirm the following: - selected paper source - attachment of the rear cover - connection of each harness and the logic board...
  • Page 14 - Clean the paper path with a cotton swab or cloth. - Clean the paper feed rollers. The back side of paper gets smeared. - Clean the platen rib (clean the paper path with a cotton swab or cloth). - Confirm that the platen ink absorber fits in place properly.
  • Page 15 - Replace the - scanning unit, - logic board, or - document pressure plate sheet. Streaks or smears on the image scanned - Clean the platen glass and the FAU lamp. from film, or no image at all. - Replace the - logic board, or - scanning unit.

  • Page 16: Repair

    MP970 TABLE OF CONTENTS 3. REPAIR 3-1. Notes on Service Part Replacement (and Disassembling / Reassembling) Service part Adjustment / settings Operation check Notes on replacement Logic board ass'y - Before removal of the logic - EEPROM information print After replacement: board ass'y, remove the power 1.

  • Page 17: Notes On Service Part Replacement

    Input carriage lift gear portions. [See 3-3. Adjustment / Easy-Scroll Wheel base Settings, (3) Grease application, for details.] Document pressure plate After replacement: unit 1. Confirm the document pressure plate sheet position. [See 3-3. Adjustment / Document pressure plate Settings, (2) Document sheet pressure plate sheet replacement, for details.]...
  • Page 18 MP970 TABLE OF CONTENTS 3-2. Special Notes on Repair Servicing (Click on the image to enlarge it.) Be sure to protect the machine from static electricity in repair servicing, especially the LCD, operation panel board, scanner unit, logic board, card board, and IrDA board.
  • Page 19 How to remove the side cover R 1. Basic idea 2) Slide the cover horizontally. 1) Move 2.5mm upward 2. Details (The scanner, front door, and cassette are not described to provide a better A: Release this part from the boss on the main case.
  • Page 20 3) Remove the document cover (document pressure plate unit). <While slightly pushing the left and right hinges toward the center, pull the cover upward to remove it. The cover will not be removed just by pulling it.> <Remove the scanner unit FFC> <Disconnect the 3 connectors and the ground wire of the operation panel harness (fastened to the chassis).>...
  • Page 21 5) Remove the scanner unit. <Disconnect the scanner motor cable connector from the logic board. (Be cautious of the rib of the main case.)> <Disengage the scanner lock arm from the scanner unit.> <While rotating the scanner unit slightly toward the outside, release the scanner lock arm from the scanner unit.> Photo up: Scanner unit 6) Remove the main case unit.
  • Page 22 Photo down: The claw of the main case (on the upper side Photo down: View from the bottom side. of the card board). View from the above. 20 / 45...
  • Page 23 (2) Operation panel removal 1) Remove the FAU protective sheet, then remove the screws from the bottom of the document cover (8 screws). <Remove the top cover from the base, while exercising caution not to break the claws.> 2) Remove the panel frame from the bottom cover (5 screws - one screw fastens the panel harness ground wire to the chassis).
  • Page 24 3) Remove the LCD and panel board from the panel frame. <Hold the LCD hinge by inserting the both noses of a long-nose plier into the holes in the hinge. Then, slide the hinge against the spring to remove the LCD from the panel frame.> <Remove the panel chassis, and panel board (8 screws).>...
  • Page 25 4) Remove the Easy-Scroll Wheel from the panel board. <Be cautious not to touch the grease between the wheel and the wheel base.> 3-3. Adjustment / Settings, (3) Grease application. (3) Cable wiring and connection 1) Wiring on the right side <The cables are fit in the bottom case>...
  • Page 26 2) Seen from the back side of the machine (Notice the DC 3) Right side of the machine (AC adapter and bottom case harness position.) removed) (4) Emblem removal Push the emblem top to remove from the double-sided adhesive tape. 24 / 45...
  • Page 27 (5) Printer unit separation from the bottom case (how to remove the screw under the purge unit) 1) Rotate the purge unit gear toward the rear side of the machine to unlock the carriage. 2) Slide the carriage to the opposite of the home position (to the left). 3) Remove the screw.

  • Page 28: Adjustment / Settings

    MP970 TABLE OF CONTENTS 3-3. Adjustment / Settings (1) Paper feed motor adjustment 1) When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by the blue arrow in the photo below).
  • Page 29 (3) Grease application 1) Printer unit Grease / Number of Drawing Part name Where to apply grease / oil Grease / oil oil amount drops x (mg) locations 1 Chassis ass'y Entire surface the carriage slider contacts Floil KG107A 27 to 54 3 x 1 2 Adjust plate L Carriage shaft cam L sliding portion...
  • Page 30 28 / 45...
  • Page 31 2) Operation panel / Easy-Scroll Wheel Grease / Number of Drawing Part name Where to apply grease / oil Grease / oil oil amount drops x (mg) locations Easy-Scroll Wheel Easy-Scroll Wheel sliding portions (15) Floil KG107A 9 to 18 1 x 4 base Joint of the ring keys (up / down / right /...
  • Page 32 MP970 TABLE OF CONTENTS (5) User mode Function Procedures Remarks Nozzle check pattern printing Perform via the machine operation panel, or from Set a sheet of plain paper (A4 or Letter) in the MP driver Maintenance tab. the rear tray or the cassette which is selected on the Paper Feed Switch button.
  • Page 33 Alarm LED.) 4) When the Power LED lights in blue (and "Service Mode CANON Idle" is displayed on the LCD), press the Stop/Reset button the specified number of time(s) according to the function listed in the table below, then press the ON/OFF button. (Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in blue, starting with Alarm LED.)
  • Page 34 0 times Blue (Power) No change of the destination 1 time Orange (Alarm) Japan Supported 2 times Blue (Power) Korea No sales of the MP970 3 times Orange (Alarm) Not supported 4 times Blue (Power) Europe Supported 5 times Orange (Alarm)
  • Page 35 <Ink absorber counter resetting> Reset the ink absorber counter (to 0%) when the ink absorber is replaced, or when necessary after the logic board is replaced. 1) In the service mode, press the Stop/Reset button 4 times, then press the ON/OFF button. The ink absorber counter value of the EEPROM is reset to 0%.
  • Page 36 3 times HP BrightWhite 4 times Canon Extra, STEINBEIS - Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in blue. - If the Stop/Reset button is NOT pressed, and only the ON/OFF button is pressed, the machine remains in the LF / Eject correction mode.
  • Page 37 3) In the printout, select the Pattern No. in which streaks or lines are the least noticeable. 3-1) LF correction value Press the Stop/Reset button the same number of time(s) as the selected Pattern No., then press the ON/OFF button. Selected pattern number Number of times the Stop/Reset button is pressed (M) 1 time 0 times...
  • Page 38 L = 1 HR-101 L = 2 GF-500 / Office Planner L = 3 HP Bright White Canon Extra, L = 4 STEINBEIS 1 sheet of paper is printed. No（L>=5） - LF correction pattern on the left LF / Eject correction...
  • Page 39 <Left margin correction> Adjust the left margin for duplex printing or printing from the cassette. 1) Duplex printing from the rear tray and cassette In the left margin correction mode, press the Stop/Reset button 1 time, then press the ON/OFF button 1 time. Duplex printing is performed from the rear tray and cassette.
  • Page 40 Left margin correction flowchart: 38 / 45...
  • Page 41 39 / 45...
  • Page 42 <Button and LCD test> Confirm the operation after replacement of the operation panel unit, board, or LCD unit. 1) In the button and LCD test mode, press the Stop/Reset button. The LCD turns blue, waiting for a button to be pressed. 2) Press each button of the operation panel.
  • Page 43 4-4) When the Easy-Scroll Wheel is rotated counterclockwise 1 round (24 steps, and all the segments are in blue), press the OK button. The color pattern is displayed on the LCD. If there is any segment that is not in blue when the OK button is pressed, the display remains unchanged. 5) Adjust the transparent color and LCD flicker, as follows: 5-1) Press the OK button.
  • Page 44 MP970 TABLE OF CONTENTS 3-4. Verification Items (1) Service test print <Service test print sample> 43 / 45...
  • Page 45 START Reading of the VrefPWM value from the EEPROM From 01h to 1Fh (hexadecimal)? Initial VrefPWM value: 72h (3.6 inch model) VrefPWM register setting "WANG50.bmp" pattern, with the VrefPWM value (hexadecimal) at the bottom of the LCD. VrefPWM= 16 Adjustment end? Press [OK].
  • Page 46 (2) Ink absorber counter value print <Print sample> <3-4. Verification Items> 44 / 45...
  • Page 47 MP970 TABLE OF CONTENTS 4. MACHINE TRANSPORTATION This section describes the procedures for transporting the machine for returning after repair, etc. 1) In the service mode, press the ON/OFF button to finish the mode, and confirm that the paper lifting plate of the rear tray is raised.
  • Page 48 MP970 / 120V(CA) 2181B006AA MP970 / 220V-240V(EUM) 2181B007AA MP970 / 220V-240V(EMB) 2181B008AA MP970 / 220V-240V(GB) 2181B009AA MP970 / 220V-240V(FR) 2181B011AA MP970 / 220V-240V(AU) 2181B012AA MP970 / 220V-240V(ASA) JUL. 2007 QY8-31D4-000 COPYRIGHT © 2007 CANON INC. CANON MP970 0707 N 0.00-0...
  • Page 49 Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period. Canon will issue a new editions of this manual.
  • Page 50 ABOUT THIS MANUAL A. ILLUSTRATION INDEX For illustration index, the parts layout illustrations in this parts catalog are listed in abbreviated form in order of illustration number to identify the pages they appear on. To find an illustration of a part, see the ILLUSTRATION INDEX. B.
  • Page 51 Contents A. ILLUSTRATION INDEX B. PARTS LAYOUT & PARTS LIST FIGURE 1 PACKING CONTENTS & PRINT HEAD FIGURE 2 AC ADAPTER FIGURE 3 EXTERNAL COVERS & SCANNER UNIT FIGURE 4 DOCUMENT PRESSURE PLATE UNIT FIGURE 5 OPERATION PANEL UNIT FIGURE 6 MAIN CASE UNIT & FRONT DOOR UNIT FIGURE 7 CARD BORAD ASS'Y &...
  • Page 52 ILLUSTRATION INDEX PACKING CONTENTS & PRINT HEAD AC ADAPTER FIGURE 1 FIGURE 2 EXTERNAL COVERS & SCANNER UNIT DOCUMENT PRESSURE PLATE UNIT FIGURE 3 FIGURE 4 OPERATION PANEL UNIT MAIN CASE UNIT & FRONT DOOR UNIT FIGURE 5 FIGURE 6...
  • Page 53 CARD BOARD ASS'Y & IrDA BOARD ASS'Y LOGIC BOARD ASS'Y FIGURE 7 FIGURE 8 BOTTOM CASE UNIT & INK ABSORBER KIT SHEET FEED UNIT FIGURE 9 FIGURE 10 CARRIAGE UNIT PLATEN UNIT FIGURE 11 FIGURE 12...
  • Page 54 PURGE UNIT PAPER FEED & CARRIAGE LIFT PART FIGURE 13 FIGURE 14 OPTION & CONSUMABLES TOOL FIGURE 15 FIGURE 16...
  • Page 55 PARTS LAYOUT & PARTS LIST FIGURE 1 PACKING CONTENTS & PRINT HEAD...
  • Page 56 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QA4-1117-000 TRAY, CD SUB W/ CDR PRINTING QL2-1449-000 CDR TRAY ASS'Y W/ CDR PRINTING QY6-0062-010 PRINT HEAD QH2-2716-000 CORD, POWER 220V-240V(EUM, EMB, ASA, MY) QH2-2719-000 CORD, POWER 100V-120V QK1-0776-000 CORD, POWER 220V-240V(AU) QK1-3761-000 CORD, POWER...
  • Page 57     FIGURE 2 AC ADAPTER...
  • Page 58 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QK1-3670-000 AC ADAPTER: 100V-240V 50/60Hz...
  • Page 59     FIGURE 3 EXTERNAL COVERS & SCANNER UNIT...
  • Page 60 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC1-9023-000 EMBLEM FOR JAPAN QC1-9024-000 EMBLEM FOR OTHER REGIONS QC2-4900-000 EMBLEM FOR FRANCE QM3-2220-000 SCANNER UNIT QM3-2216-000 PAPER SUPPORT UNIT QM3-2218-000 CASSETTE UNIT QC2-4666-000 DOOR, CARD QM3-2215-000 SIDE COVER L UNIT QM3-2213-000 SIDE COVER R UNIT QM3-2212-000...
  • Page 61     FIGURE 4 DOCUMENT PRESSURE PLATE UNIT...
  • Page 62 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QM3-2225-000 DOCUMENT PRESSURE PLATE UNIT QC2-4705-000 FRAME, DOCUMENT PRESSURE PLATE QC2-1799-000 SHEET, DOCUMENT PRESSURE PLATE QM3-2233-000 FILM GUIDE UNIT QC2-4703-000 COVER, TOP QC2-4633-000 COVER, FLAPPER QC2-4634-000 SPRING, TORSION QC2-4635-000 SPRING, TORSION QM3-2228-000 HINGE UNIT QM3-2445-000...
  • Page 63     FIGURE 5 OPRATION PANEL UNIT...
  • Page 64 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC2-4711-000 FRAME, PANEL QM3-2238-000 PANEL BOARD ASS'Y QC2-4629-000 COVER, PANEL BOARD QC2-4724-000 COVER, LCD FRONT QC2-4725-000 COVER, LCD TOP QC2-4726-000 WINDOW, LCD QK1-3926-000 CORE, RING QC2-4867-000 HINGE, LCD QC2-4868-000 SPRING, HINGE QC2-4756-000 COVER, FUNCTION KEY QC2-4718-000...
  • Page 65     FIGURE 6 MAIN CASE UNIT & FRONT DOOR UNIT B-11...
  • Page 66 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QM3-2210-000 MAIN CASE UNIT QM3-2211-000 FRONT DOOR UNIT QC1-6573-000 DAMPER, DOOR B-12...
  • Page 67     FIGURE 7 CARD BOARD ASS'Y & IrDA BOARD ASS'Y B-13...
  • Page 68 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC1-9987-000 COVER, GAP W/O CDR PRINTING QM3-2219-000 INNER COVER UNIT QC2-0424-000 ARM, RELEASE QM3-2240-000 IRDA BOARD ASS'Y QM3-2239-000 CARD BOARD ASS'Y QM3-2469-000 PICTBRIDGE HARNESS ASS'Y QM3-2475-000 CARD GND HARNESS ASS'Y QM3-2470-000 CARD HARNESS ASS'Y B-14...
  • Page 69     FIGURE 8 LOGIC BOARD ASS'Y B-15...
  • Page 70 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QM3-2237-000 LOGIC BOARD ASS'Y B-16...
  • Page 71     FIGURE 9 BOTTOM CASE UNIT & INK ABSORBER KIT B-17...
  • Page 72 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QY5-0181-000 ABSORBER KIT QM3-2217-000 BOTTOM CASE UNIT B-18...
  • Page 73     FIGURE 10 SHEET FEEDER UNIT B-19...
  • Page 74 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QM3-0259-000 DC CONNECTOR ASS'Y QM3-0296-000 MOTOR MULTI HARNESS ASS'Y QM3-2471-000 ENCODER MULTI HARNESS ASS'Y QC2-5978-000 COVER, PAPER FEED GUIDE QM3-2230-000 SHEET FEEDER UNIT B-20...
  • Page 75     FIGURE 11 CARRIAGE UNIT B-21...
  • Page 76 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC1-6526-000 FILM, TIMING SLIT STRIP QC1-6201-000 SPRING, LEAF QC2-0080-000 CLIP, SHAFT R QC2-4426-000 CAM, CARRIAGE SHAFT R QC2-0083-000 CLIP, SHAFT L QK1-1500-000 MOTOR, CARRIAGE QC2-4425-000 CAM, CARRIAGE SHAFT L QM3-2231-000 CARRIAGE UNIT QC2-0414-000 SHAFT, CARRIAGE...
  • Page 77     FIGURE 12 PLATEN UNIT B-23...
  • Page 78 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC2-4888-000 ABSORBER, INK QM3-2242-000 PLATEN UNIT QC1-6619-000 SPRING, TENSION QC2-4881-000 FILM, TIMING SLIT DISK EJECT B-24...
  • Page 79     FIGURE 13 PURGE UNIT B-25...
  • Page 80 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QM3-0033-010 PURGE UNIT QC2-0089-000 TUBE, INK QC2-0030-000 COVER, INK TUBE QC2-0085-000 TUBE, INK JOINT B-26...
  • Page 81     FIGURE 14 PAPER FEED & CARRIAGE LIFT PART B-27...
  • Page 82 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QC1-9941-000 CAM, SWING ARM LOCK QL2-1450-000 PR LIFT SHAFT ASS'Y QC1-6232-000 SPRING, TENSION QM2-3890-000 PAPER GUIDE UNIT QC1-9937-000 SPRING, TORSION QM2-3886-010 PRESSURE ROLLER ASS'Y QM3-1273-000 CARRIAGE LIFT SENSOR UNIT QC2-4433-000 CARRIAGE LIFT GEAR BASE UNIT QC2-1873-000 GEAR, INPUT CARRIAGE LIFT...
  • Page 83 OPTION & CONSUMABLES FIGURE 15 OPTION & CONSUMABLES...
  • Page 84 FIGURE & PART RANK QTY DESCRIPTION REMARKS KEY No. NUMBER 15 - BLACK INK TANK BCI-7eBK CONSUMABLES PHOTO CYAN INK TANK BCI-7ePC CONSUMABLES BLACK INK TANK BCI-9BK CONSUMABLES MAGENTA INK TANK BCI-7eM CONSUMABLES CYAN INK TANK BCI-7eC CONSUMABLES PHOTO MAGENTA INK TANK BCI-7ePM CONSUMABLES YELLOW INK TANK BCI-7eY CONSUMABLES...
  • Page 85 SCREW & WASHER LIST   FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. XB4-7300-809 SCREW, TAP, BINDING HEAD, M3X8 XB1-2300-605 SCREW, MACHINE, M3X6 XB4-7300-805 SCREW, TP, BH3X8 XB1-2300-405 SCREW, MACH.BH, M3X4 XA9-1752-000 SCREW, TAP, WASHER HEAD, M3X12 XB2-4300-605 SCREW, W/WASHER, M3X6 XA9-1754-000 SCREW, BIND, M2.6X4(RED)
  • Page 86 TOOL     FIGURE 16 TOOL...
  • Page 87 FIGURE & PART NUMBER RANK QTY DESCRIPTION REMARKS KEY No. QY9-0057-000 LUBE, FLOIL KG107A, OIL...
  • Page 88 NUMERICAL INDEX   FIGURE FIGURE PART NUMBER & DESCRIPTION PART NUMBER & DESCRIPTION KEY No. KEY No. QA4-1117-000 TRAY, CD SUB QC2-4888-000 ABSORBER, INK QC1-6201-000 SPRING, LEAF QC2-4900-000 EMBLEM QC1-6202-000 11 SPRING, COIL QC2-5978-000 COVER, PAPER FEED GUIDE QC1-6212-000 10 GEAR, IDLER CARRIAGE LIFT QH2-2716-000 CORD, POWER QC1-6225-000...

Table of Contents