Putting Into Operation; Energy Saving Tips - Bonnet Neve MULTIFROZEN PLUS User Instructions

Modello - Modèle - Model
Modell - Modelo
Fabbricante - Constructeur
Manufacturer - Hersteller
Fabricante

14. PUTTING INTO OPERATION

If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand
for at least three hours before being started to allow the lubricating oil to settle in the compressor.
Failure to do so can cause total destruction of the compressor refrigerating system.
Check that the voltage on the identification plate is the same as that of the network.
THE ELECTRICAL SUPPLY LINE TO WHICH THE REFRIGERATOR WILL
HAVE TO BE CONNECTED IS TO BE PROTECTED BY A VERY SENSITIVE
DIFFERENTIAL SWITCH (Rc=16A,Dc=30mA); IT IS ALSO TO BE LINKED
TO THE GENERAL EARTHING PLANT.
Earthing is necessary and compulsory by law.
Absolutely never use reduction units, patch cords, adapters or multiple socket
outlets to connect the counter. DIRECTLY connect the equipment to the mains.
The cable should be fully extended and located where it is unilikely to be struck, caught or stepped on, away from water
and the other liquids and heat sources and must not be damaged. In case of breakage of the power cable of the cabinet,
it must be replaced by the manufacturer or by instruction it change of it.
Follow the manufacturer's instructions to install the unit, using qualified personnel and complying with the electrical
regulations for the specific country.
Incorrect installation may cause injury and damage; the manufacturer is not liable for this.
The manufacturer disclaims all responsability for any damage to people or things due to
incorrect observance of this rule.
15. SEPARATE LIGHTS POWER SUPPLY
(OPTIONAL)
ON REQUEST, THE COUNTER CAN BE
EQUIPPED WITH A SEPARATE LIGHTS
POWER SUPPLY.

16. ENERGY SAVING TIPS

• Install the appliance in a dry, well-ventilated room away from heat sources (radiator, cooking surface and so on) and in a position
out of direct sunlight.
• Follow the installation instructions to ensure adequate ventilation. Insufficient ventilation to the back of the appliance causes an
increase in energy consumption and reduces cooling efficiency.
• The internal temperature of the appliance depends on the room temperature, how often the doors are opened and where the
appliance is placed. These factors have to be taken into account when setting the thermostat. Only open the doors when strictly
necessary.
• Let hot food and drink cool down before placing them in the appliance.
• The positioning of the shelves in the fridge has no effect on energy efficiency.
• The fridge compartment light system uses a LED light, which at the same time ensures more efficient lighting and reduced energy
consumption.
17. OUTER CLEANING
WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
For a good preservation of the cabinet's body a periodical cleaning is necessary.
1. EXTERNAL BODY: When necessary, the external body should be cleaned with a cloth and a neutral soap and water solution.
Use also mop for cleaning under the unit and vacuum cleaner for removing dirt or dust.
2. STAINLESS STEEL SURFACES: Wash with warm water and mild detergent, rinse well and dry with soft cloth. Avoid
scouring pads etc. which will spoil the finish of the stainless steel.
3. SURFACES IN PLASTIC MATERIAL: Wash with warm water and mild detergent, rinse well and dry with soft cloth; under
no circumstances should alcohol, methylated spirits or solvents be used.
4. GLASS SURFACES: Only use products specifically designed for glass cleaning; It is not advisable to use ordinary water
which can leave a film of calcium on the surface of the glass.
MULTIFROZEN PLUS
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
2 0 / 6 0
PAGE
UM000487
N° DOC