IDENTEC SOLUTIONS iPOINT Si Hardware User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

IDENTEC SOLUTIONS

Model IDS1001

iPOINT Si

HARDWARE USER MANUAL

Table of Contents

Summary of Contents for IDENTEC SOLUTIONS iPOINT Si

Page 1 IDENTEC SOLUTIONS Model IDS1001 iPOINT Si HARDWARE USER MANUAL...
Page 2 Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without the prior written authorization from IDENTEC SOLUTIONS. Disclaimer and Limitation of Liability IDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents do not make any express or implied warranties or representations with respect to such information including, without limitation, warranties as to non-infringement, reliability, suitability for a particular purpose and accuracy.
Page 3 European Declaration of Conformity according to RED Directive IDENTEC SOLUTIONS AG hereby declares that the device iPOINT is in conformity with the essential requirements of Directive 2014/53/EU. The declaration of conformity can be found at: www.identecsolutions.com...
Page 4 These notes are not sufficient to guarantee complete protection from electrostatic discharges! We recommend the use of suitable protective equipment. IDENTEC SOLUTIONS does not accept the return of products where the regulations concerning the ESD precautions and protective packaging materials were not followed.
Page 5 We recommend that only personnel, original products, spare and replacement parts authorized by IDENTEC SOLUTIONS be used for installation, service and repair. IDENTEC SOLUTIONS does not accept any responsibility for materials used, work carried out or possible consequences from unauthorized third party vendors.
Page 6: Table Of Contents
6. Maintenance ................................23 6.1 Exchanging an iPOINT within the daisy chain ....................23 6.2 Firmware Update ............................24 6.3 Spare Parts ..............................24 6.4 Returns ................................24 7. Technical Specifications ............................25 Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 7: Preface
IDENTEC SOLUTIONS reserves the right to make changes and updates to the content contained herein. It is the user’s responsibility to contact the service department for any possible changes or updates to operating and maintenance procedures.
Page 8: Introduction
The iPOINT can used as a standalone device or in a daisychain of devices. See Section 2.3 for more details. Following is a description of the wireless technologies that are available within the iPOINT Device. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 9: Uhf Interface
The LF Interface uses IDENTEC’s LF Marker technology. Zone location at Low Frequency can be achieved BOOST with a configurable field range up to 5 Meters. This allows Tag detection in a specific area. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 10: Nfc Interface
The NFC Interface is a Near Field Communication interface. The iPOINT can be used as an entry terminal or for other NFC communication. The range to the Tag is around 10-15cm and is compatible with the i-Q355 Series of Tags as well as standard NFC cards. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 11: System Components - Tags
Tracking and Tracing Localization Environmental Data Sensing i-B350 Tags IDENTEC SOLUTIONS' i-B350 tags are designed to be cost effective and easy to implement, while offering maximum flexibility. The beacon ILR ® Tags continually send out their ID at pre-programmed intervals. They do not need to be interrogated in order for them to send their information—...
Page 12: Ports Overview & Topologies
RJ45 RS422 cable connector to the master port of the next i-PORT in the daisy chain. RS422 SLAVE Leave this connector open at the last device in the chain. PoE Power installation: For other system configurations, please contact Identec Solutions Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 13 Make sure power supply can handle all iPOINTs in the system USB Mode (5V) Local USB mode over Mini-USB Connector for debugging, low-power operation and Configuration No Slave mode under USB operation Maximum power consumption of an iPOINT is 7W. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 14: Poe Connector & Pinout
Ethernet compatible.  If devices are powered by the RJ45 cabling of the RS422 Master/Slave, wire gauge must be at least AWG24 (0.25 mm²). View into the connector = crimp/solder side of plug Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 15: Usb Connector & Pinout
A Standard Mini-USB Cable and connector can be used to connect to the iPOINT  Standard 5V power is supplied to the device View into the connector (female, receptacle) Description Colour Data - White Data + Green ID / not Connected None Black Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 16: Usb Only Mode - Function And Specification
There is a feature in the iPOINT where automatic detection of the housing being opened can be communicated to the Host system. This can be used as a safety feature or as a tamper alert. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 17: Initial Operation / Configuration
OK. Blinks red if the voltage is too low or a Hardware issue is detected NFC (top) This is the NFC Card read LED. Is green when access is granted, red when access is denied. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 18: Mechanical Information & Installation
Note: when replacing the lid, be sure that the sealing gasket is correctly in place. Note: The rest of the housing cannot be accessed. There is no settings or modifications to be made there. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 19: Mounting Options
Warning: Don’t screw the mounting plate directly to a metal surface that extends the size of the whole device. This will have an influence on the UHF and LF performance. If a metal fixing surface is required, please use the extension bracket as a standoff. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 20: Optional Extra: Pole Mount Bracket Kit
The bracket can be mounted to a wall with M8 Bolts or via threaded rods (e.g. wall anchors) o The bracket can also be mounted onto vertical or horizontal poles o Refer to “Pole Mount Bracket Kit – Quick Installation Guide” documentation for more details. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 21: Optional Extra: Extension Bracket Kit
The bracket can be mounted to a wall with M8 Bolts or via threaded rods (e.g. wall anchors) o Multiple mounting options, including use of the pole mount bracket o Refer to “Extension Bracket Kit – Quick Installation Guide” documentation for more details. Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 23: Troubleshooting
 Exchange only one unit after another, not several in one step.  Exchange the device with one of the same type.  If necessary, configure the iPOINT in your system software Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.
Page 24: Firmware Update
Tags and iPOINT X devices are complex electronic power units on which the customer can carry out only very limited repairs. Normally the repairs are carried out at IDENTEC SOLUTIONS or possibly at a distributor. Before a part is sent in for repair a short examination should be conducted.
Page 25: Technical Specifications
Si: 1200g Order Code iPOINT Si (IDS1001) 455970 Pole Mount Bracket (kit) 456001 The communication range depends on environmental conditions and national regulation limits Other country frequencies are available, please contact IDENTEC SOLUTIONS Copyright © 2020 IDENTEC SOLUTIONS. All rights reserved.

This manual is also suitable for:

Ids1001

IDENTEC SOLUTIONS iPOINT Si Hardware User Manual

Quick Links

Related Manuals for IDENTEC SOLUTIONS iPOINT Si

Summary of Contents for IDENTEC SOLUTIONS iPOINT Si

This manual is also suitable for:

Table of Contents