Whelen Engineering Company WAT OR5001V Installation And Service Manual page 30

MODEL 71080 ( ) SERIES LED BEACON
LED Flashing Anti-Collision Light Assembly
(150 eff. Cd) (14 VDC & 28 VDC)
71080 series LED beacons are FAA TSO compliant Self-Contained LED
(Ref. Class I - 150 effective candlepower). They are designed to replace a range of products.
Refer to models and descriptions below.
ELECTRICAL, Models: 01, 04, 05, 14, 15, 20, 51, 55: Ship with 12" Flying Leads
Models: 07, 17, 08, 18: MS3102R10SL-3P Connector
MECHANICAL, Models: 04, 14, 08, 18 are designed to replace existing beacons
utilizing a 5-Hole mounting pattern on a 4.656 diameter bolt circle (Whelen
70285 series/7090501 series or 70900 with A440 adapter).
Models: 05, 15, 07, 17 are 3 ¾" opening designed to fit inside an A440
mounting adapter, mounting holes to fit in place of rotating beacons,
Whelen Model HRCFA, or 7090004, 05 series LED beacons
Model 71080 ( ) LED Rotorcraft Beacon Specifications
Model Part
Numbers Number
7108001 01-0771080-01
7108004 01-0771080-04
7108005 01-0771080-05
7108006 01-0771080-06
7108007 01-0771080-07
7108008 01-0771080-08
7108014 01-0771080-14
Flying Leads, Lower
7108015 01-0771080-15
Flying Leads, Lower
7108017 01-0771080-17
7108018 01-0771080-18
7108020 01-0771080-20
EC120, 130, 135 Adapter,
7108030 01-0771080-30
7108051 01-0771080-51
7108055 01-0771080-55
Operation
The Model 71080 series LED Anti-Collision light assembly meets
the requirements of FAR 91.205(c)(3).
CONTINUED AIRWORTHINESS: The 71080 series LED anti-colli-
sion light assembly is designed with 8 vertical columns consist-
ing of 4 LEDs each. Should any one LED or any vertical column
fail, the unit must be repaired or replaced. Inspect the lens and
replace if there is excessive scratching, discoloration or cracking.
INSTALLATION PROCEDURES: The following information is to
assist in the installation of a Whelen LED Flashing Anti-collision
Light System.
1. The installation procedure described in the following text will
be confined to a single light installation, but is identical for
multiple light installations.
2. Using the "suggested mounting hole pattern" prepare the
aircraft for means to secure the LED Flashing Anti-Collision
Light assembly. Remove any existing mounting adapters.
3. 28 VDC (+) and (-) ground leads equipped with an appropriate
sized breaker to be supplied to the LED Flashing Anti-Collision
Light Assembly System. Both leads must be connected by an
30
Document #05131 Rev. E
LED LIGHT ASSEMBLIES
(Red LED's)
Mount /
Voltage
Hole Pattern
A470A Mount
5 Hole Adapter,
Flying Leads
3.75" Adapter,
Flying Leads
A470A Mount
3.75" Adapter,
MSConn, Lower
5 Hole Adapter,
MSConn
28 VDC
5 Hole Adapter,
3.75" Adapter,
3.75" Adapter,
MSConn, Lower
5 Hole Adapter,
MSConn, Lower
EC120,130,
135 Adapter
MSConn
A470A Mount,
Mate-N-Lock
14 VDC
3.75" Adapter,
Flying Leads
Anti-Collision
lights
Lens /
Approvals
LED Color
FAA TSO-C96a Class I & III (150 ecp)
FAA TSO-C96a Class I
FAA TSO-C96a Class I & III (150 ecp)
FAA TSO-C96a Class I (150 ecp)
FAA TSO-C96a Class I & III (150 ecp)
Clear
FAA TSO-C96a Class I
polycarbonate
hard-coat
LED Red
FAA TSO-C96a Class I & III (150 ecp)
FAA TSO-C96a Class I
FAA TSO-C96a Class I & III (150 ecp)
approved FAA connection. Insure that the wire leads are clear
of any obstructions and ty-wrap as required.
4. Install the light assembly by first removing the lens.
Remove the adapter plate. Attach the adapter plate to
the aircraft mounting holes. Refer to page 2. Reinstall the light
assembly and lens.
5. All inverted (bottom) mounted units shall require waterproof
ing of the flasher base assembly to the aircraft. Note: Drill a
1/8" hole in the center of the lens for bottom mount units.
6. Check all avionics systems for interference from this installa-
tion.
7. A flight check should be performed by a properly certified
pilot.
8. Update aircraft records, as required & obtain FAA field
approval for installation, if not covered under STC eligibility
list.
Model 71080 Series
Class I helicopter beacon (Red only), can now replace Model
70905 beacon, now available with new style mounts and electrical
connections (28 &14 VDC).
Input Current Weight
0.65 lbs. (295gm)
0.80 lbs. (363gm)
0.75 lbs. (340gm)
0.45 amps 2.0 amps
average peak
0.65 lbs. (295gm)
0.87 lbs. (395gm)
0.80 lbs. (363gm)
0.75 lbs. (340gm)
0.45 amps 2.0 amps
0.87 lbs. (395gm)
average peak
0.75 lbs. (340gm)
0.87 lbs. (395gm)
0.65 lbs. (295gm)
0.90 amps 4.0 amps
average peak
0.75 lbs. (340gm)