Montageanleitung S. 3/34 1. Montage Vorbereitung Lesen Sie diese Montageanleitung gut durch und bewahren Sie sie in der Nähe der Sauna auf. So können Sie jederzeit Produktinformationen nachlesen. Sie finden diese Montageanleitung auch im Downloadbereich unserer Webseite auf www.sentiotec.com/downloads. Wichtige Hinweise: ●...
Montageanleitung S. 4/34 1.1. Benötigtes Werkzeug ● Hammer und Beilageholz oder einen Gummihammer ● Akkuschrauber mit Bits für Kreuzschrauben und Torx ● Rollmaßband ● Bohrer mit Durchmesser 3 mm, 10 mm, 20 - 30 mm (für Stromkabel Saunaofen) ● Wasserwaage ●...
Montageanleitung S. 5/34 1.2. Wartung und Reinigung ● Die Sauna sollte mit einem feuchten Tuch gereinigt werden. Verwenden Sie nur warmes Wasser - keine Reinigungsmittel. ● Wird die Sauna längere Zeit nicht benutzt, empfehlen wir, die Kabine einmal im Monat aufzuheizen. Harzgallen sind kein Reklamationsgrund.
Montageanleitung S. 6/34 1.4. Stückliste ALASKA MINI INFRA+ Az Bezeichnung Maß Bodenrahmen 1 Bodenrahmen 156 x 9 x 4 cm 1 Bodenrahmen 108 x 9 x 4 cm 1 Bodenrahmen 102 x 9 x 4 cm 1 Bodenrahmen 64 x 9 x 4 cm Wandelemente 1 Wandelement A/B mit Strahlerausschnitt 193 x 48 x 4 cm...
Page 7
Montageanleitung S. 7/34 Az Bezeichnung Maß Inneneinrichtung 1 Bank 147 x 62 x 9 cm 1 Fußauftrittplatte 80 x 35 x 9 cm 2 Fußauftritt Füße 43 x 33 x 4 cm 2 Fußauftritt Strebe, 2 x 45º schräg 49,5 x 8 x 2 cm 2 Rückenlehne 58 x 25,5 x 4 cm 1 Banksichtblende...
Montageanleitung S. 8/34 2. Montage der Kabine Die Kabine kann „rechts“ oder „links“ aufgebaut werden, beachten Sie dazu die Grundrisspläne auf Seite 30 und Seite 31. 2.1. Montage des Bodenrahmens 156 cm Grundriss „rechts“ 64 cm Bohrer 3mm, 3 Stk. Schrauben 4 x 70 mm 156 cm Grundriss „links“...
Montageanleitung S. 9/34 2.2. Montage der Wandelemente Die Ecksteher werden mittels „Multiclips“ mit den Wandelementen verbunden. Die weiteren Wandelemente sind mit Nut und Feder verbunden und werden miteinander verschraubt. A bezeichnet immer die Sichtseite, dies ist auf der Oberseite der Wand- elemente gekennzeichnet.
Page 10
Montageanleitung S. 10/34 Montage Ecksteher mit Wandelement Montieren Sie die Wandelemente mit den Eckstehern am Boden vor und setzen Sie diese Ecken dann auf den Bodenrahmen auf. Stecken Sie den Ecksteher von oben nach unten auf die Wandelemente. Achten Sie dabei auf die korrekte Ausrichtung der „Multiclips“ (siehe unten). Der Eck- steher muss bündig mit den Wandelementen sein.
Page 11
Montageanleitung S. 11/34 Montage Wandelemente Das Elektroelement hat Bohrungen zum Verlegen der Kabel. Position siehe Grundrisspläne auf Seite 30 und Seite 31. Elektroelement...
Page 12
Montageanleitung S. 12/34 Verschrauben der Wandelemente Überprüfen Sie die rechten Winkel, bevor Sie die Wandelemente verschrauben. Beachten Sie den Tipp auf Seite 4. Bohrer 3 mm, 4 Stk. Schrauben 4 x 70 mm...
Page 13
Montageanleitung S. 13/34 Ecksteher und Steher für Glas...
Page 14
Montageanleitung S. 14/34 Glaselement Element oberhalb der Tür Das Element für Grundriss rechts auswählen...
Page 15
Montageanleitung S. 15/34 Bohrer 3 mm, 2 Stk. Schrauben 4 x 70 mm...
Montageanleitung S. 18/34 2.4. Montage Lüftungsschieber Bohrer 3 mm, 4 Stk. Schrauben 3 x 40 mm 2.5. Montage Inneneinrichtung Bankauflageleisten Bohrer 3 mm, 3 Stk. Schrauben 5 x 70 mm 2 Stk. Schrauben 4 x 60 mm...
Page 19
Montageanleitung S. 19/34 Bohrer 3 mm, 3 Stk. Schrauben 5 x 70 mm Schrauben 4 x 60 mm...
Page 20
Montageanleitung S. 20/34 Banksichtblende 4 Stk. Schrauben 4 x 60 mm Bank...
Page 21
Montageanleitung S. 21/34 Fußauftritt 6 Stk. Schrauben 4 x 70 mm...
Page 22
Montageanleitung S. 22/34 4 Stk. Schrauben 3,5 x 35 mm...
Page 23
Montageanleitung S. 23/34 Infrarot-Strahler und Rückenlehnen Anschlussbox oben Beschriftung lesbar 4 Stk. Schrauben 4 x 60 mm 4 Stk. Schrauben 3 x 20 mm Bohrer 3mm, 4 Stk. Schrauben 4 x 70 mm...
Montageanleitung S. 24/34 2.6. Montage Zubehör Saunaleuchte Leuchtmittel einsetzen (nicht im Lieferumfang enthalten) Bohrer 3mm, 2 Stk. Schrauben 4 Stk. Schrauben 3 x 40 mm...
Page 25
Montageanleitung S. 25/34 Ofenschutzgitter Bohren Sie vor der Montage des Ofenschutzgitters den Auslass für das Ofenkabel im Elektroelement. 12 Stk. Schrauben 3 x 40 mm Ofenschutzgitter individuell kürzbar...
Montageanleitung S. 26/34 2.7. Montage Glastür Die untere Bohrung des Türgriffs ist in 92,4 cm Höhe. Die Ausrichtung der Beschläge wird durch die Justierung / Drehung der beiden Kunststoffeinlagen vorgenommen.
Page 27
Montageanleitung S. 27/34 Türgriff und Überschubblech Silikonring in Bohrungen einlegen Kunststoff Beilagscheibe bei Niro- Griff beilegen...
Montageanleitung S. 28/34 2.8. Montage Dachkranz Montieren Sie den Dachkranz erst nachdem Sie die Kabel zum Saunaofen und zur Saunasteuerung eingezogen haben. Möglicherweise muss die Leiste beim Elektroelement ausgeschnitten werden. Bohrer 3 mm, 9 Stk. Schrauben 3 x 40 mm...
Montageanleitung S. 29/34 2.9. Montage Dachabdeckleiste Montieren Sie die Dachabdeckleiste erst nachdem Sie die Kabel zum Saunaofen und zur Saunasteuerung eingezogen haben. Möglicherweise muss die Leiste beim Elektroelement ausgeschnitten werden. 12 Stk. Schrauben 3 x 40 mm...
Gebrauchsanweisung für den Anwender S. 32/34 3.3. Änderungen bei Montage Grundriss „links“ Für die Montage von Ecksteher und Steher für das Glas (Seite 14) Entfernen Sie die Muliclips vom Ecksteher und dem Steher für Glas. Verwenden Sie die beiliegende Schablone für die neue Positionierung der Mulitclips.
Page 34
GmbH | Division of Harvia Group | Oberregauer Straße 48, A-4844 Regau T +43 (0) 7672/277 20-567 | F -801 | info@sentiotec.com | www.sentiotec.com...
Page 35
Solid wood sauna ALASKA MINI INFRA+ 160 x 110 x 204 cm INSTRUCTIONS FOR INSTALLATION AND USE English ALASKA-MN-IR+ Version 07/18 Ident. no. 1-030-245...
Page 36
Table of Contents 1. Preparing for installation 1.1. Tools required 1.2. Maintenance and cleaning 1.3. Disposal 1.4. ALASKA MINI INFRA+ parts list 2. Cabin installation 2.1. Base frame installation 2.2. Wall element installation 2.3. Ceiling installation 2.4. Ventilation slit installation 2.5.
Instructions for installation and use p. 3/34 1. Preparing for installation Read these installation instructions carefully and keep them within reach when using the sauna, so that you can look up product information at any time. These installation instructions can also be found in the downloads section of our website: www.sentiotec.com/downloads.
Instructions for installation and use p. 4/34 1.1. Tools required ● Hammer with a wooden head or a mallet ● Cordless screwdriver with bits for cross-head screws and Torx ● Roller tape measure ● Drill bits with a diameter of 3 mm, 10 mm, 20 - 30 mm (for sauna heater power cable) ●...
Instructions for installation and use p. 5/34 1.2. Maintenance and cleaning ● The sauna should be cleaned with a damp cloth. Only use warm water – no cleaning products. ● We recommend heating the cabin once a month if the sauna is not used for a long time.
Instructions for installation and use p. 6/34 1.4. ALASKA MINI INFRA+ parts list No. of items Name Dimensions Base frame 1 Base frame 156 x 9 x 4 cm 1 Base frame 108 x 9 x 4 cm 1 Base frame 102 x 9 x 4 cm 1 Base frame 64 x 9 x 4 cm...
Page 41
Instructions for installation and use p. 7/34 No. of items Name Dimensions Interior fittings 1 Bench 147 x 62 x 9 cm 1 Foot step panel 80 x 35 x 9 cm 2 Foot step feet 43 x 33 x 4 cm 2 Foot step struts, 2 x 45°...
Instructions for installation and use p. 8/34 2. Cabin installation The cabin can have a right or left set up, please note the corresponding floor plans on Page 30 and Page 31. 2.1. Base frame installation 156 cm Right floor plan 64 cm 3 mm drill bit, 3 screws 4 x 70 mm 156 cm...
Instructions for installation and use p. 9/34 2.2. Wall element installation The corner posts are connected to the wall elements using Multiclips. The other wall elements are connected by tongue and groove and are screwed together. A always refers to the visible side. This is labelled on the top side of the wall elements.
Page 44
Instructions for installation and use p. 10/34 Installing corner posts with wall elements Pre-assemble the wall elements with the corner posts on the floor and then place these posts on the base frame. Insert the corner post on the wall elements, moving it downwards. When doing this, ensure that the Multiclips are correctly aligned (see below).
Page 45
Instructions for installation and use p. 11/34 Installing wall elements The electrical element has drill holes for laying cables. For the position, see floor plans on Page 30 and Page 31. Electrical element...
Page 46
Instructions for installation and use p. 12/34 Screwing wall elements together Check the right angle before screwing the wall elements together. Observe the tip on page 4. 3 mm drill bit, 4 screws 4 x 70 mm...
Page 47
Instructions for installation and use p. 13/34 Corner post and post for glass...
Page 48
Instructions for installation and use p. 14/34 Glass element Element above the door Select the element for the right floor plan...
Page 49
Instructions for installation and use p. 15/34 3 mm drill bit, 2 screws 4 x 70 mm...
Instructions for installation and use p. 18/34 2.4. Ventilation slit installation 3 mm drill bit, 4 screws 3 x 40 mm 2.5. Installing interior fittings Bench support slats 3 mm drill bit, 3 screws 5 x 70 mm 2 screws 4 x 60 mm...
Page 53
Instructions for installation and use p. 19/34 3 mm drill bit, 3 screws 5 x 70 mm Screws 4 x 60 mm...
Page 54
Instructions for installation and use p. 20/34 Bench screen 4 screws 4 x 60 mm Bench...
Page 55
Instructions for installation and use p. 21/34 Foot step 6 screws 4 x 70 mm...
Page 56
Instructions for installation and use p. 22/34 4 screws 3.5 x 35 mm...
Page 57
Instructions for installation and use p. 23/34 Infrared radiator and backrests Connection box, top Label legible 4 screws 4 x 60 mm 4 screws 3 x 20 mm 3 mm drill bit, 4 screws 4 x 70 mm...
Instructions for installation and use p. 24/34 2.6. Installing accessories Sauna lamp Insert lamp (not included in the scope of delivery) 3 mm drill bit, 2 screws 4 screws 3 x 40 mm...
Page 59
Instructions for installation and use p. 25/34 Heater protection grille Before installing the heater protection grille, drill the outlet for the heater cable in the electrical element. 12 screws 3 x 40 mm Heater protection grille can be shortened to length...
Instructions for installation and use p. 26/34 2.7. Installing glass door The bottom drill hole of the door handle is 92.4 cm high. The alignment of the fittings is achieved by adjusting / rotating both plastic inserts.
Page 61
Instructions for installation and use p. 27/34 Door handle and sleeve plate Insert silicone ring in the drill holes Attach plastic washers on the stainless steel handle...
Instructions for installation and use p. 28/34 2.8. Installing roof trim Install the roof trim only after you have inserted the cable to the sauna heater and to the sauna control unit. The slat on the electrical element may possibly have to be cut out. 3 mm drill bit, 9 screws 3 x 40 mm...
Instructions for installation and use p. 29/34 2.9. Installing ceiling cover slat Install the ceiling cover slat only after you have inserted the cable to the sauna heater and to the sauna control unit. The slat on the electrical element may possibly have to be cut out. 12 screws 3 x 40 mm...
Instructions for use for the user p. 32/34 3.3. Changes to the left floor plan installation For installing corner posts and posts for the glass (page 14) Remove the Multiclips from the corner posts and the post for the glass. Use the supplied template for the new positioning of the Multiclips.
Page 68
GmbH | Division of Harvia Group | Oberregauer Straße 48, A-4844 Regau Phone +43 (0) 7672/277 20-567 | Fax -801 | info@sentiotec.com | www.sentiotec.com...
Page 69
Sauna en bois massif ALASKA MINI INFRA+ 160 x 110 x 204 cm INSTRUCTIONS DE MONTAGE ET MODE D’EMPLOI Français ALASKA-MN-IR+ Version 07/18 d’ident. 1-030-245...
Page 70
Table des matières 1. Préparation du montage 1.1. Outils requis 1.2. Entretien et nettoyage 1.3. Élimination 1.4. Nomenclature ALASKA MINI INFRA+ 2. Montage de la cabine 2.1. Montage du cadre de plancher 2.2. Montage des éléments muraux 2.3. Montage du toit 2.4.
Instructions de montage et mode d‘emploi p. 3/34 1. Préparation du montage Lisez attentivement les présentes instructions de montage et gardez-les à proximité de l’appareil. Vous avez ainsi accès à tout moment aux informations sur le produit. Vous trouverez également ces instructions de montage dans la rubrique de téléchargement de notre site Internet www.sentiotec.com/downloads.
Instructions de montage et mode d‘emploi p. 4/34 1.1. Outils requis ● Marteau et cales ou maillet en caoutchouc ● Visseuse électrique avec bits pour vis en croix et Torx ● Ruban de mesure ● Foret de 3 mm de diamètre, 10 mm, 20-30 mm (pour câble électrique poêle de sauna) ●...
Instructions de montage et mode d‘emploi p. 5/34 1.2. Entretien et nettoyage ● Le sauna doit être nettoyé au moyen d’un chiffon humide. N’utilisez que de l’eau chaude, pas de détergent. ● Si le sauna n’est pas utilisé pendant une période prolongée, nous recom- mandons de chauffer la cabine une fois par mois.
Instructions de montage et mode d‘emploi p. 6/34 1.4. Nomenclature ALASKA MINI INFRA+ Nb Désignation Dimensions Cadre de plancher 1 Cadre de plancher 156 x 9 x 4 cm 1 Cadre de plancher 108 x 9 x 4 cm 1 Cadre de plancher 102 x 9 x 4 cm 1 Cadre de plancher 64 x 9 x 4 cm...
Page 75
Instructions de montage et mode d‘emploi p. 7/34 Nb Désignation Dimensions Équipement intérieur 1 Banc 147 x 62 x 9 cm 1 Plaque de marchepied 80 x 35 x 9 cm 2 Marchepied pieds 43 x 33 x 4 cm 2 Marchepied étais, inclinaison 2 x 45°...
Instructions de montage et mode d‘emploi p. 8/34 2. Montage de la cabine La cabine peut être montée « à droite » ou « à gauche ». Référez-vous aux plans Page 30 et Page 31. 2.1. Montage du cadre de plancher 156 cm Plan «...
Instructions de montage et mode d‘emploi p. 9/34 2.2. Montage des éléments muraux Fixez les montants d’angle aux éléments muraux au moyen des « multiclips ». Les autres éléments muraux sont reliés pas des rainures et des languettes, et sont vissés les uns aux autres. A désigne toujours le côté...
Page 78
Instructions de montage et mode d‘emploi p. 10/34 Montage des montants d’angle sur les éléments muraux Prémontez les éléments muraux et les montants d’angle au sol, puis placez ces angles sur le cadre de plancher. Placez le montant d’angle du haut vers le bas sur les éléments muraux. Assurez-vous que l’orientation des «...
Page 79
Instructions de montage et mode d‘emploi p. 11/34 Montage des éléments muraux Des trous sont prévus sur l’élément électrique afin de poser le câble. Pour la position, consultez Page 30 et Page 31. Élément électrique...
Page 80
Instructions de montage et mode d‘emploi p. 12/34 Vissage des éléments muraux Contrôlez les angles droits avant de visser les éléments muraux. Consul- tez le conseil page 4. Foret de 3 mm, 4 vis 4 x 70 mm...
Page 81
Instructions de montage et mode d‘emploi p. 13/34 Montant d’angle et montant pour verre...
Page 82
Instructions de montage et mode d‘emploi p. 14/34 Élément en verre Élément au-dessus de la porte Sélection de l’élément pour le plan à droite...
Page 83
Instructions de montage et mode d‘emploi p. 15/34 Foret de 3 mm, 2 vis 4 x 70 mm...
Instructions de montage et mode d‘emploi p. 18/34 2.4. Montage du registre d’aération Foret de 3 mm, 4 vis 3 x 40 mm 2.5. Montage de l’équipement intérieur Baguettes d’appui de banc Foret de 3 mm, 3 vis 5 x 70 mm 2 vis 4 x 60 mm...
Page 87
Instructions de montage et mode d‘emploi p. 19/34 Foret de 3 mm, 3 vis 5 x 70 mm Vis 4 x 60 mm...
Page 88
Instructions de montage et mode d‘emploi p. 20/34 Écran de banc 4 vis 4 x 60 mm Banc...
Page 89
Instructions de montage et mode d‘emploi p. 21/34 Marchepied 6 vis 4 x 70 mm...
Page 90
Instructions de montage et mode d‘emploi p. 22/34 4 vis 3,5 x 35 mm...
Page 91
Instructions de montage et mode d‘emploi p. 23/34 Radiateur infrarouge et dossiers Boîtier de raccordement en haut Inscription lisible 4 vis 4 x 60 mm 4 vis 3 x 20 mm Foret de 3 mm, 4 vis 4 x 70 mm...
Instructions de montage et mode d‘emploi p. 24/34 2.6. Montage des accessoires Éclairage de sauna Mise en place des ampoules (non compris dans la livraison) Foret de 3 mm, 2 vis 4 vis 3 x 40 mm...
Page 93
Instructions de montage et mode d‘emploi p. 25/34 Grille de protection du poêle Avant le montage de la grille de protection du poêle, percez la sortie pour le câble du poêle dans l’élément électrique. 12 vis 3 x 40 mm Grille de protection du poêle pouvant être raccourcie individuellement...
Instructions de montage et mode d‘emploi p. 26/34 2.7. Montage de la porte en verre L’alésage inférieur de la poignée de porte se trouve à une hauteur de 92,4 cm. L’orientation des ferrures est effectuée en ajustant/tournant les deux armatures en plastique.
Page 95
Instructions de montage et mode d‘emploi p. 27/34 Poignée de porte et tôle extérieure Introduction de la bague en Pose des rondelles de calage en silicone dans les alésages plastique pour poignée inox...
Instructions de montage et mode d‘emploi p. 28/34 2.8. Montage de la couronne Ne montez la couronne qu’après avoir inséré les câbles vers le poêle de sauna et la commande de sauna. La baguette au niveau de l’élément électrique doit éventuellement être coupée. Foret de 3 mm, 9 vis 3 x 40 mm...
Instructions de montage et mode d‘emploi p. 29/34 2.9. Montage de la baguette couvre-joint Ne montez la baguette couvre-joint qu’après avoir inséré les câbles vers le poêle de sauna et la commande de sauna. La baguette au niveau de l’élément électrique doit éventuellement être coupée. 12 vis 3 x 40 mm...
Mode d‘emploi pour l‘utilisateur P. 32/34 3.3. Modifications lors du montage selon le plan « à gauche » Pour le montage de montants d’angle et de montants pour le verre (page 14) Retirez les multiclips pour montant d’angle et montant pour le verre. Utilisez les gabarits fournis pour le nouveau positionnement des multiclips.
Page 102
GmbH | Division of Harvia Group | Oberregauer Straße 48, A-4844 Regau T +43 (0) 7672/277 20-567 | F -801 | info@sentiotec.com | www.sentiotec.com...
Page 103
Sauna in legno massiccio ALASKA MINI INFRA+ 160 x 110 x 204 cm ISTRUZIONI DI MONTAGGIO E D’USO Italiano ALASKA-MN-IR+ Versione 07/18 N. ident. 1-030-245...
Page 104
Indice 1. Preparazione per il montaggio 1.1. Attrezzi necessari 1.2. Manutenzione e pulizia 1.3. Smaltimento 1.4. Elenco dei pezzi ALASKA MINI INFRA+ 2. Montaggio della cabina 2.1. Montaggio del telaio di base 2.2. Montaggio degli elementi parete 2.3. Montaggio del tetto 2.4.
Istruzioni di montaggio e d’uso P. 3/34 1. Preparazione per il montaggio Leggere con attenzione le presenti istruzioni di montaggio e conservarle in pros- simità della sauna. In questo modo è possibile controllare in qualsiasi momento le informazioni relative al prodotto. Le presenti istruzioni di montaggio si trovano anche nella sezione download del nostro sito web all’indirizzo: www.sentiotec.com/downloads.
Istruzioni di montaggio e d’uso P. 4/34 1.1. Attrezzi necessari ● Martello e pezzo di legno oppure martello in gomma ● Avvitatore elettrico con punte per viti con testa a croce e viti Torx ● Metro a nastro avvolgibile ● Punte per trapano da 3 mm, 10 mm, 20-30 mm (per cavo elettrico della stufa per sauna) ●...
Istruzioni di montaggio e d’uso P. 5/34 1.2. Manutenzione e pulizia ● La sauna deve essere pulita con un panno umido. Utilizzare solo acqua calda senza detergenti. ● Se la sauna non viene utilizzata per un tempo prolungato, si consiglia di riscaldare la cabina una volta al mese.
Istruzioni di montaggio e d’uso P. 6/34 1.4. Elenco dei pezzi ALASKA MINI INFRA+ Pz. Denominazione Dimensioni Telaio di base 1 Telaio di base 156 x 9 x 4 cm 1 Telaio di base 108 x 9 x 4 cm 1 Telaio di base 102 x 9 x 4 cm 1 Telaio di base...
Page 109
Istruzioni di montaggio e d’uso P. 7/34 Pz. Denominazione Dimensioni Allestimento interno 1 Panca 147 x 62 x 9 cm 1 Poggiapiedi 80 x 35 x 9 cm 2 Piedini poggiapiedi 43 x 33 x 4 cm 2 Sostegni poggiapiedi, 2x inclinati a 45° 49,5 x 8 x 2 cm 2 Schienale 58 x 25,5 x 4 cm...
Istruzioni di montaggio e d’uso P. 8/34 2. Montaggio della cabina La cabina può essere montata “a destra” o “a sinistra”; consultare le piante a Pagina 30 e Pagina 31. 2.1. Montaggio del telaio di base 156 cm Pianta “a destra” 64 cm Punta per trapano da 3 mm, 3 viti 4 x 70 mm 156 cm...
Istruzioni di montaggio e d’uso P. 9/34 2.2. Montaggio degli elementi parete I montanti angolari vengono collegati agli elementi parete mediante “multiclip”. Gli altri elementi parete vengono collegati con scanalatura e linguetta e avvitati tra loro. A: indica sempre il lato a vista ed è riportata sulla parte superiore degli elementi parete.
Page 112
Istruzioni di montaggio e d’uso P. 10/34 Montaggio del montante angolare con elemento parete Assemblare sul pavimento gli elementi parete con i montanti angolari e successivamente montarli sul telaio di base. Innestare i montanti angolari dall’alto verso il basso sugli elementi parete. Nel far- lo, prestare attenzione all’orientamento corretto delle “multiclip”...
Page 113
Istruzioni di montaggio e d’uso P. 11/34 Montaggio degli elementi parete L’elemento per cavi elettrici ha dei fori per la posa dei cavi. Per la posi- zione, vedere le piante a Pagina 30 e Pagina 31. Elemento per cavi elettrici...
Page 114
Istruzioni di montaggio e d’uso P. 12/34 Collegamento a vite degli elementi parete Verificare l’ortogonalità degli elementi parete prima di avvitarli tra loro. Seguire l’indicazione a pagina 4. Punta per trapano da 3 mm, 4 viti 4 x 70 mm...
Page 115
Istruzioni di montaggio e d’uso P. 13/34 Montante angolare e montante per vetro...
Page 116
Istruzioni di montaggio e d’uso P. 14/34 Elemento in vetro Elemento sopraporta Selezionare l’elemento per pianta “a destra”...
Page 117
Istruzioni di montaggio e d’uso P. 15/34 Punta per trapano da 3 mm, 2 viti 4 x 70 mm...
Istruzioni di montaggio e d’uso P. 18/34 2.4. Montaggio del pannello scorrevole di aerazione Punta per trapano da 3 mm, 4 viti 3 x 40 mm 2.5. Montaggio dell’allestimento interno Listelli di supporto panca Punta per trapano da 3 mm, 3 viti 5 x 70 mm 2 viti 4 x 60 mm...
Page 121
Istruzioni di montaggio e d’uso P. 19/34 Punta per trapano da 3 mm, 3 viti 5 x 70 mm Viti 4 x 60 mm...
Page 122
Istruzioni di montaggio e d’uso P. 20/34 Pannello di rivestimento panca 4 viti 4 x 60 mm Panca...
Page 123
Istruzioni di montaggio e d’uso P. 21/34 Poggiapiedi 6 viti 4 x 70 mm...
Page 124
Istruzioni di montaggio e d’uso P. 22/34 4 viti 3,5 x 35 mm...
Page 125
Istruzioni di montaggio e d’uso P. 23/34 Irradiatore a infrarossi e schienale Scatola di connessione superiore Scritta leggibile 4 viti 4 x 60 mm 4 viti 3 x 20 mm Punta per trapano da 3 mm, 4 viti 4 x 70 mm...
Istruzioni di montaggio e d’uso P. 24/34 2.6. Montaggio accessori Lampada Inserire una lampadina (non compresa nella fornitura) Punta per trapano da 3 mm, 2 viti 4 viti 3 x 40 mm...
Page 127
Istruzioni di montaggio e d’uso P. 25/34 Griglia di protezione stufa Prima del montaggio della griglia di protezione della stufa eseguire il foro di uscita per il cavo della stufa nell’elemento per cavi elettrici. 12 viti 3 x 40 mm Griglia di protezione stufa accorciabile...
Istruzioni di montaggio e d’uso P. 26/34 2.7. Montaggio della porta in vetro Il foro inferiore della maniglia porta è a un’altezza di 92,4 cm. L’orientamento delle guarnizioni viene eseguito regolando / ruotando i due inserti in plastica.
Page 129
Istruzioni di montaggio e d’uso P. 27/34 Maniglia porta e lamierino di battuta Inserire un anello di silicone nei fori Applicare rondelle di plastica nelle maniglie Nirosta...
Istruzioni di montaggio e d’uso P. 28/34 2.8. Montaggio del coronamento tetto Montare il coronamento tetto solo dopo aver inserito i cavi per la stufa della sauna e per il comando della sauna. Se possibile, ritagliare il listello dell’elemento per cavi elettrici. Punta per trapano da 3 mm, 9 viti 3 x 40 mm...
Istruzioni di montaggio e d’uso P. 29/34 2.9. Montaggio del listello di copertura del tetto Montare il listello di copertura del tetto solo dopo aver inserito i cavi per la stufa della sauna e per il comando della sauna. Se possibile, ritagliare il listello dell’elemento per cavi elettrici.
Istruzioni d’uso per l’utilizzatore P. 32/34 3.3. Differenze di montaggio per la pianta “a sinistra” Per il montaggio di montante angolare e montante per il vetro (pagina 14) Rimuovere le multiclip dal montante angolare e dal montante per il vetro. Utilizzare la dima in dotazione per il nuovo posizionamento dei multiclip.
Instrukcja montażu S. 3/34 1. Przygotowanie montażu Przeczytaj uważnie niniejszą instrukcję montażu. Przechowuj ją w pobliżu sauny. Dzięki temu możliwe będzie w każdej chwili przeczytanie informacji o produkcie. Niniejsza instrukcja montażu jest również dostępna do pobrania na naszej stronie internetowej www.sentiotec.com/downloads. Ważne wskazówki: ●...
Instrukcja montażu S. 4/34 1.1. Wymagane narzędzia ● Młotek i przekładka z drewna lub młotek gumowy ● Wkrętarka akumulatorowa z bitami do wkrętów krzyżowych i Torx ● Taśma miernicza ● Wiertło o średnicy 3 mm, 10 mm, 20–30 mm (do przewodu zasilającego piec sauny) ●...
Instrukcja montażu S. 5/34 1.2. Konserwacja i czyszczenie ● Sauna powinna być czyszczona wilgotną ściereczką. Używaj tylko ciepłej wody – żadnych detergentów. ● Jeśli sauna nie jest używana przez dłuższy czas, zaleca się rozgrzewanie kabiny raz w miesiącu. Pęcherze żywiczne nie są podstawą do reklamacji. W drewnie świerko- wym często zdarzają...
Instrukcja montażu S. 6/34 1.4. Lista części ALASKA MINI INFRA+ Nazwa Wymiar Rama podłogi 1 Rama podłogi 156 x 9 x 4 cm 1 Rama podłogi 108 x 9 x 4 cm 1 Rama podłogi 102 x 9 x 4 cm 1 Rama podłogi 64 x 9 x 4 cm Elementy ścienne...
Page 143
Instrukcja montażu S. 7/34 Nazwa Wymiar Urządzenie wnętrza 1 Ławka 147 x 62 x 9 cm 1 Płyta podnóżkowa 80 x 35 x 9 cm 2 Podnóżek na stopy 43 x 33 x 4 cm 2 Podnóżek z podporą, 2 x 45° ukośną 49,5 x 8 x 2 cm 2 Tylne oparcie 58 x 25,5 x 4 cm...
Instrukcja montażu S. 8/34 2. Montaż kabiny Kabina może zostać zamontowana „na prawą stronę lub „na lewą stronę”, należy sprawdzić plany rzutu poziomego na Strona 30 oraz Strona 31. 2.1. Montaż ramy podłogowej 156 cm Rzut poziomy „na prawą stronę” 64 cm Wiertło 3 mm, 3 szt.
Instrukcja montażu S. 9/34 2.2. Montaż elementów ściennych Stojaki narożne są łączone za pomocą „multiklipów” z elementami ściennymi. Pozostałe elementy ścienne są łączone na pióro i wpust i są połączone śrubami. A wskazuje zawsze na stronę widoczną, jest ona oznaczana na górze elementów ściennych.
Page 146
Instrukcja montażu S. 10/34 Montaż stojaka narożnego z elementem ściennym Zamontuj elementy ścienne ze stojakami narożnymi na podłodze, a na- stępnie umieść te stojaki na ramie podłogi. Nasuń stojak narożny z góry na dół na elementy ścienne. Upewnij się, że mul- tiklipsy są...
Page 147
Instrukcja montażu S. 11/34 Montaż elementów ściennych Element elektryczny ma otwory do układania przewodów. Sprawdź położenie na planie rzutów poziomych na Strona 30 i Strona 31. Element elektryczny...
Page 148
Instrukcja montażu S. 12/34 Łączenie śrubami elementów ściennych Sprawdź kąt prosty przed połączeniem elementów ściennych śrubami. Postępuj zgodnie ze wskazówką na stronie 4. Wiertło 3 mm, 4 szt. śrub 4 x 70 mm...
Page 149
Instrukcja montażu S. 13/34 Stojak narożny i stojak na szkło...
Page 150
Instrukcja montażu S. 14/34 Element szklany Element powyżej drzwi Wybierz element z rzutu poziomowego na prawą stronę...
Page 151
Instrukcja montażu S. 15/34 Wiertło 3 mm, 2 szt. śrub 4 x 70 mm...
Instrukcja montażu S. 18/34 2.4. Montaż zasuwki do wentylacji Wiertło 3 mm, 4 szt. śrub 3 x 40 mm 2.5. Montaż urządzenia wnętrza Listy nakładane na ławkę Wiertło 3 mm, 3 szt. śrub 5 x 70 mm 2 szt. śrub 4 x 60 mm...
Page 155
Instrukcja montażu S. 19/34 Wiertło 3 mm, 3 szt. śrub 5 x 70 mm Śrubki 4 x 60 mm...
Page 156
Instrukcja montażu S. 20/34 Osłona ławki 4 szt. śrub 4 x 60 mm Ławka...
Page 157
Instrukcja montażu S. 21/34 Podnóżek 6 szt. śrub 4 x 70 mm...
Page 158
Instrukcja montażu S. 22/34 4 szt. śrub 3,5 x 35 mm...
Page 159
Instrukcja montażu S. 23/34 Promiennik podczerwieni i oparcie dla pleców Skrzynka przyłączeniowa na górze Czytelne oznaczenie 4 szt. śrub 4 x 60 mm 4 szt. śrub 3 x 20 mm Wiertło 3 mm, 4 szt. śrub 4 x 70 mm...
Instrukcja montażu S. 24/34 2.6. Montaż akcesoriów Lampa do sauny Zamontuj lampę (nie wchodzi w zakres dostawy) Wiertło 3 mm, 2 szt. śrub 4 szt. śrub 3 x 40 mm...
Page 161
Instrukcja montażu S. 25/34 Krata ochronna pieca Przed montażem kraty ochronnej pieca wywierć w elemencie elektrycz- nym wylot na przewód pieca. 12 szt. śrub 3 x 40 mm Można indywidualnie przyciąć kratę ochronną pieca...
Instrukcja montażu S. 26/34 2.7. Montaż drzwi szklanych Dolny otwór uchwytu drzwiowego znajduje się na wysokości 92,4 cm. Ustawienie okuć wykonuje się poprzez wyrównanie/obrót obu wkładek wykonanych z tworzywa sztucznego.
Page 163
Instrukcja montażu S. 27/34 Uchwyt drzwiowy i blacha nakładana z góry Włóż pierścień silikonowy do otworów Włóż podkładkę z tworzywa sztucznego do uchwytu Niro...
Instrukcja montażu S. 28/34 2.8. Montaż występu dachu Zamontuj występ dachu dopiero po przeprowadzeniu przewodu do pieca sauny i sterowania sauną. Listwa może wymagać wycięcia w elemencie elektrycznym. Wiertło 3 mm, 9 szt. śrub 3 x 40 mm...
Instrukcja montażu S. 29/34 2.9. Montaż listwy zakrywającej dach Zamontuj listwę zakrywającą dach dopiero po przeprowadzeniu przewo- du do pieca sauny i sterowania sauną. Listwa może wymagać wycięcia w elemencie elektrycznym. 12 szt. śrub 3 x 40 mm...
Gebrauchsanweisung für den Anwender S. 32/34 3.3. Zmiany w przypadku montażu „na lewą stronę“ W przypadku montażu stojaka narożnego i stojaka na szkło (strona 14) Usuń multiklipy ze stojaka narożnego i stojaka na szkło. Użyj dołączonego szablonu do nowego ustawienia multiklipów. Element powyżej drzwi (strona 15) Wybierz element z rzutu poziomowego na lewą...
Page 170
GmbH | Division of Harvia Group | Oberregauer Straße 48, A-4844 Regau T +43 (0) 7672/277 20-567 | F -801 | info@sentiotec.com | www.sentiotec.com...
Page 171
Sauna maciça ALASKA MINI INFRA+ 160 x 110 x 204 cm MANUAL DE MONTAGEM Português ALASKA-MN-IR+ Versão 07/18 N.º artigo 1-030-245...
Page 172
Índice 1. Preparação para a montagem 1.1. Ferramentas necessárias 1.2. Manutenção e limpeza 1.3. Eliminação 1.4. Lista de peças do ALASKA MINI INFRA+ 2. Montagem da cabina 2.1. Montagem da armação do chão 2.2. Montagem dos elementos de parede 2.3. Montagem do teto 2.4.
Manual de montagem P. 3/34 1. Preparação para a montagem Leia atentamente o manual de montagem e guarde-o nas proximidades da sauna. Poderá, assim, ler as informações sobre o produto a qualquer momento posteriormente. Este manual de montagem também está disponível na área de downloads da nossa página web em www.sentiotec.com/downloads.
Manual de montagem P. 4/34 1.1. Ferramentas necessárias ● Martelo e madeira suplementar ou um martelo de borracha ● Aparafusadora sem fios com pontas para parafusos em cruz e Torx ● Rolo de fita métrica ● Brocas com um diâmetro de 3 mm, 10 mm, 20–30 mm (para o cabo de alimentação do aquecedor de sauna) ●...
Manual de montagem P. 5/34 1.2. Manutenção e limpeza ● A sauna deverá ser limpa com um pano húmido. Utilize apenas água quente. Não utilize qualquer produto de limpeza. ● Se a sauna não for utilizada por um longo período, recomendamos que aqueça a cabina uma vez por mês.
Manual de montagem P. 6/34 1.4. Lista de peças do ALASKA MINI INFRA+ Quant. Designação Medida Armação do chão 1 Armação do chão 156 x 9 x 4 cm 1 Armação do chão 108 x 9 x 4 cm 1 Armação do chão 102 x 9 x 4 cm 1 Armação do chão 64 x 9 x 4 cm...
Page 177
Manual de montagem P. 7/34 Quant. Designação Medida Equipamento interior 1 Banco 147 x 62 x 9 cm 1 Placa do degrau 80 x 35 x 9 cm 2 Pés do degrau 43 x 33 x 4 cm 2 Escora do degrau, inclinação 2 x 45° 49,5 x 8 x 2 cm 2 Encosto 58 x 25,5 x 4 cm...
Manual de montagem P. 8/34 2. Montagem da cabina A cabina pode ser montada “à direita” ou “à esquerda”. A este respeito, tenha em atenção os planos nas páginas Página 30 e Página 31. 2.1. Montagem da armação do chão 156 cm Plano “à...
Manual de montagem P. 9/34 2.2. Montagem dos elementos de parede Os suportes de canto são ligados aos elementos de parede através de “multicli- pes”. Os outros elementos de parede são ligados por meio de ranhuras e molas e aparafusados uns aos outros. A designa sempre o lado visível.
Page 180
Manual de montagem P. 10/34 Montagem dos suportes de canto com os elementos de parede Monte previamente os elementos de parede com os suportes de canto no chão e coloque depois esses cantos sobre a armação do chão. Insira o suporte de canto nos elementos de parede, de cima para baixo. Ao fa- zê-lo, tenha em atenção o alinhamento correto dos “multiclipes”...
Page 181
Manual de montagem P. 11/34 Montagem dos elementos de parede O elemento elétrico dispõe de orifícios para passar os cabos. Consulte a posição nos planos, nas páginas Página 30 e Página 31. Elemento elétrico...
Page 182
Manual de montagem P. 12/34 Aparafusamento dos elementos de parede Verifique os ângulos direitos antes de aparafusar os elementos de parede. Tenha em atenção a dica na página 4. Broca de 3 mm, 4 parafusos de 4 x 70 mm...
Page 183
Manual de montagem P. 13/34 Suportes de canto e suportes para vidro...
Page 184
Manual de montagem P. 14/34 Elemento de vidro Elemento por cima da porta Selecionar o elemento para o plano à direita...
Page 185
Manual de montagem P. 15/34 Broca de 3 mm, 2 parafusos de 4 x 70 mm...
Manual de montagem P. 18/34 2.4. Montagem da corrediça de ventilação Broca de 3 mm, 4 parafusos de 3 x 40 mm 2.5. Montagem do equipamento interior Barras de apoio para o banco Broca de 3 mm, 3 parafusos de 5 x 70 mm 2 parafusos de 4 x 60 mm...
Page 189
Manual de montagem P. 19/34 Broca de 3 mm, 3 parafusos de 5 x 70 mm Parafusos de 4 x 60 mm...
Page 190
Manual de montagem P. 20/34 Anteparo do banco 4 parafusos de 4 x 60 mm Banco...
Page 191
Manual de montagem P. 21/34 Degrau 6 parafusos de 4 x 70 mm...
Page 192
Manual de montagem P. 22/34 4 parafusos de 3,5 x 35 mm...
Page 193
Manual de montagem P. 23/34 Radiador de raios infravermelhos e encostos Caixa de ligação em cima Inscrição legível 4 parafusos de 4 x 60 mm 4 parafusos de 3 x 20 mm Broca de 3 mm, 4 parafusos de 4 x 70 mm...
Manual de montagem P. 24/34 2.6. Montagem dos acessórios Luz da sauna Colocar a lâmpada (não incluída no volume de fornecimento) Broca de 3 mm, 2 parafusos 4 parafusos de 3 x 40 mm...
Page 195
Manual de montagem P. 25/34 Grelha de proteção do aquecedor Antes de montar a grelha de proteção do aquecedor, faça um furo para a saída do cabo do aquecedor no elemento elétrico. 12 parafusos de 3 x 40 mm Grelha de proteção do aquecedor encurtável individualmente...
Manual de montagem P. 26/34 2.7. Montagem da porta de vidro O furo inferior do puxador da porta encontra-se a 92,4 cm de altura. O alinhamento das ferragens é efetuado através do ajuste/rotação de ambas as inserções de plástico.
Page 197
Manual de montagem P. 27/34 Puxador da porta e chapa de transferência Colocar o anel de silicone nos orifícios Inserir a anilha plana de plástico no puxador de aço inoxidável...
Manual de montagem P. 28/34 2.8. Montagem do friso do teto Monte o friso do teto só depois de ter puxado os cabos para o aquecedor da sauna e para o controlo da sauna. A barra poderá ter de ser cortada junto do elemento elétrico.
Manual de montagem P. 29/34 2.9. Montagem da barra de cobertura do teto Monte a barra de cobertura do teto só depois de ter puxado os cabos para o aquecedor da sauna e para o controlo da sauna. A barra poderá ter de ser cortada junto do elemento elétrico.
Manual de instruções para o utilizador P. 32/34 3.3. Alterações na montagem do plano “à esquerda” Para a montagem dos suportes de canto e dos suportes para vidro (página 14) Remova os multiclipes do suporte de canto e do suporte para vidro. Utilize o molde fornecido para o reposicionamento dos multiclipes.
Need help?
Do you have a question about the sentiotec ALASKA MINI INFRA+ and is the answer not in the manual?
Questions and answers