Assembly - EINHELL GH-BC 43 AS Original Operating Instructions

Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method.
It may change according to how the equipment
is used and may exceed the specifi ed value in
exceptional circumstances.
The specifi ed vibration value can be used to com-
pare the equipment with other power tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Assembly

5.1 Mounting the blade guard hood
The cutting blade guard hood must be fi tted if you
wish to work with the cutting blade. The guard
hood for the cutting blade must be installed as
shown in Figures 10-11.
5.2 Joining the drive rod mechanism to the
connecting piece (Fig. 4-7)
Fit the handle screw (Item 10) as shown in Fig.
4. Open the handle screw and push the drive rod
mechanism (Item 4) into the connecting piece
Anl_SA_GH_BC_43_AS_SPK8.indb 42 Anl_SA_GH_BC_43_AS_SPK8.indb 42
GB
(Item 5). Make sure that the centering lever (Item
R) latches in the guide hole (Item H). Tighten the
handle screw. To take apart, undo the handle
screw. Press the centering lever and simultane-
ously pull the drive rod mechanism out of the
connecting piece.
5.3 Fitting / Replacing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figures 12-18. To dismantle, proceed in
reverse order.
•
Fit the carrier plate 30) onto the spline shaft
(Fig. 13)
•
Secure the cutting blade (1) on the carrier
plate (Fig. 14)
•
Place the pressure plate (31) over the thread
of the spline shaft (Fig. 15)
•
Plug on the cover of the pressure plate (32)
(Fig. 16)
•
Look for the hole in the carrier plate, line up
with the notch underneath and lock with the
supplied Hexagon key (22) in order to now
tighten the nut (24) (Fig. 17/18) Important:
Left-hand thread
5.4 Fitting the cutting line guard hood to the
blade guard hood
The cutting line guard hood must be fi tted in addi-
tion if you want to work with the cutting line.
The procedure for fi tting the guard hood for the
cutting line is shown in Figures 19-20. A blade
(Fig. 19/ Item F) on the underside of the guard
hood automatically cuts the cutting line to the
optimum length. It is covered by a guard (Fig.
19/Item G). Remove the guard before you start
working and replace it when you have fi nished
working.
5.5 Fitting the handle
Fit the handle as shown in Fig. 8-9.
5.6 Fitting / Replacing the line spool
The procedure for fi tting the line spool is shown in
Figure 21. To dismantle, proceed in reverse order.
Look for the hole in the carrier plate, line up with
the notch underneath and lock with the supplied
Hexagon key (22) in order to now screw the line
spool onto the thread. Notice! Left-hand thread.
- 42 -
06.02.2017 13:21:24 06.02.2017 13:21:24