EINHELL GH-BC 43 AS Original Operating Instructions
  1. Manuals
  2. Brands
  3. EINHELL Manuals
  4. Power Tool
  5. GH-BC 43 AS
  6. Original operating instructions

EINHELL GH-BC 43 AS Original Operating Instructions

Petrol power scythe
Hide thumbs Also See for GH-BC 43 AS:
Table of Contents

Advertisement

Quick Links

Download this manual
GB
Original operating instructions
Petrol Power Scythe
7
Art.-Nr.: 34.019.73
GH-BC 43 AS
I.-Nr.: 11013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GH-BC 43 AS and is the answer not in the manual?

Questions and answers

Related Manuals for EINHELL GH-BC 43 AS

Summary of Contents for EINHELL GH-BC 43 AS

  • Page 1 GH-BC 43 AS Original operating instructions Petrol Power Scythe Art.-Nr.: 34.019.73 I.-Nr.: 11013...
  • Page 2 - 2 -...
  • Page 3 18 20 - 3 -...
  • Page 4 28 22 - 4 -...
  • Page 5 - 5 -...
  • Page 6 - 6 -...

  • Page 7: Table Of Contents

    Table of contents 1. Safety regulations 2. Layout and items supplied 3. Intended use 4. Technical data 5. Assembly 6. Before starting 7. Operation 8. Working with the petrol power scythe 9. Maintenance 10. Cleaning, storage, transport and ordering of spare parts 11.

  • Page 8: Safety Regulations

    12. Add a little grease (gear grease) after every Important! 20 hours in operation! When using the equipment, a few safety pre- cautions must be observed to avoid injuries and damage. Please read the complete operating 2. Layout and items supplied instructions and safety regulations with due care.

  • Page 9: Intended Use

    • Remove the packaging material and any The equipment is allowed to be used only for its packaging and/or transportation braces (if prescribed purpose. Any other use is deemed to available). be a case of misuse. The user/operator and not •...

  • Page 10: Assembly

    Reduce noise generation and vibration to a fi tted in addition if you want to work with the cut- minimum! ting line. • Use only equipment that is in perfect condi- The procedure for fi tting the guard hood for the tion.

  • Page 11: Operation

    6.2 Fuel mixing table 7.2 Starting with a warm engine Mixing procedure: 40 parts petrol to 1 part oil (The equipment has been idle for less than 15-20 min.) Petrol 2-stroke oil 1. Set the equipment down on a hard, level sur- 1 liter 25 ml face.

  • Page 12: Working With The Petrol Power Scythe

    8. Working with the petrol power Cutting along fences/foundations Approach wire mesh fences, lath fences, natural scythe stone walls and foundations slowly so that you can cut close to them without striking the obstac- Extending the cutting line le with the line. If, for example, the line strikes Caution! Do not use any kind of metal wire or stones, stone walls or foundations, it will wear or metal wire encased in plastic in the line spool.

  • Page 13: Maintenance

    Preventing recoil 9.2 Grinding the safety hood blade When you work with the blade, there is a risk of The safety hood blade can become blunt over recoil if it strikes solid objects such as tree trunks, time. When you notice this, undo the screw hol- branches, tree stumps, stones or the like.

  • Page 14: Cleaning, Storage, Transport And Ordering Of Spare Parts

    10. Cleaning, storage, transport and 9.6 Setting the throttle cable If the maximum speed of the equipment drops ordering of spare parts over time and you have ruled out all the other possible causes listed in section 12 „Troubleshoo- 10.1 Cleaning ting“, it may be necessary to adjust the throttle •...

  • Page 15: Disposal And Recycling

    Putting the equipment back into operation 1. Remove the spark plug (see section 9.4). 2. Quickly tug on the starter cord to remove ex- cess oil from the combustion chamber. 3. Clean the spark plug and check that the electrode gap is correct, or insert a new spark plug with the correct electrode gap.

  • Page 16: Troubleshooting Guide

    12. Troubleshooting guide The table below contains a list of fault symptoms and explains what you can do to remedy the problem if your equipment fails to work properly. If the problem still persists after working through the list, please contact your nearest service workshop.
  • Page 17 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH. Subject to technical changes - 31 -...
  • Page 18 Warranty provisions iSC GmbH or the DIY store where you made you purchase guarantees the repair of defects or replace- ment of the equipment in accordance with the overview below. Statutory guarantee claims are unaff ec- ted. Category Example Warranty Defect with regard to material or 24 months construction...
  • Page 19 Warranty certifi cate Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
  • Page 20 EÚ a noriem pre výrobok Lýsir uppfyllingu EU-reglna og annarra staðla vöru a cikkekhez az EU-irányvonal és Normák szerint a következő konformitást jelenti ki Benzin-Motorsense GH-BC 43 AS (Einhell) 87/404/EC_2009/105/EC 2006/42/EC Annex IV 2005/32/EC_2009/125/EC Notifi ed Body: 2006/95/EC Notifi...
  • Page 21 - 169 -...
  • Page 22 - 170 -...
  • Page 23 - 171 -...
  • Page 24 EH 06/2013 (01)

Table of Contents