Fostex D-1624 Reference Manual page 101

D824/D1624 Reference Manual (Changing the Initial Settings <SETUP mode>)
Changing the Initial Settings (SETUP mode)
The SETUP mode offers the Changing the initial settings menus to configure the operating environment
of the recorder, a "Check" menu that enables you to check the number of events of each track and the
"Execution" menus to execute certain operations such as save/load and disk formatting.
The "Changing the initial settings" menus include 21 parameters as shown in <Table-1> below. These
parameters were set before the recorder was shipped from the factory and are called the initial settings.
By modifying these settings, you can change the operating environment of your recorder. The "Check"
menu provides two parameters as shown in <Table-2> : Checking the number of events and Checking
the current drive information.
The "Execution" menus in <Table-3> include six items: Title Edit?, Delete. PGM?, Load PGM?, Save PGM?,
Disk Optimize, and Disk Format?, which you can execute by selecting the corresponding SETUP menu.
In this chapter we will explain procedures only on <Table-1> "Changing the initial settings" menu (except
setting the internal clock) and <Table-2> "Check" menu. To learn how to set the internal clock, refer to
the "Quick operation guide," and on the "Execution" menu, the "Reference page" written in <Table-3>.
Parameters
Setting a time signature
Setting a Tempo
Setting the metronome function
Setting a preroll time
Setting MIDI sync output signal
Setting an MTC frame rate
Setting an MTC offset value
Setting Offset mode
Setting a reference time code
Setting the slave type
Setting the record protect function
Setting digital input tracks
Setting digital output tracks
Setting BAR/BEAT resolution mode
Setting the MIDI device ID number
Setting the operating clock
Setting the SYNC preset
Setting the Virtual LTC display
Setting the chase offset display
Setting the drive
Setting the internal clock
Check item
Check of the Event number on the track
Check of the current drive status
Execution item
Editing a program title
Deleting a program
Loading song data
Saving song data
Optimizing a Disk
Formatting a Disk
<Table-1> "Changing the initial settings" menu
Display
Signature Set ?
Tempo Map Set ?
Click ?
Preroll Time ?
Midi Sync Out ?
Frame Rate ?
MTC OFFSET
Offset Mode ?
Ref. TC ? Void!
Slave Type ?
Rec Protect ?
D. in?
D. out ?
Resolution ?
Device ID ?
Clock Sel ?
Sync Preset ?
Virtual LTC ?
Offset Disp ?
Drive Sel. ?
Date & Time Set ?
: Modes applicable program by program. They can be saved/loaded.
: Modes applicable to all programs. They cannot be saved/loaded.
<Table-2> "Check" menu
Display
NOs Of Event ?
Drive Info ?
<Table-3> "Execution" menu
Display
Title Edit PGM** ?
Delete PGM** ?
Load PGM ?
Save PGM ?
Disk Optimize ?
Disk Format ?
101
Default setting Refer page
001bar 4/4
001bar 1 120
Off
00s
MTC
25 frame
00h 59m 57s 00f 00sf
ABS
Available with option Model 8345 (Refer to APPENDIX)
Vari
Off
Analog
adat
Off
00
Int.
Available with option Model 8345 (Refer to the APPENDIX)
Available with option Model 8345 (Refer to the APPENDIX)
Available with option Model 8345 (Refer to the APPENDIX)
IDE
Please refer to the "Quick Operation Guide."
Refer page
118
119
Refer page
37
36
84
84
30
30
Community
103
105
107
108
109
109
110
111
112
112
113
114
115
116
117
121 -
Community
-
-
Community
-
-
-
-
-
-