Related Manuals for Curtis G4TBS
Summary of Contents for Curtis G4TBS
- Page 1 USER GUIDE G4 Digital Iced Tea Brewing System (Short Version) READ AND SAVE THESE INSTRUCTIONS NOTICE TO INSTALLER: Please leave this booklet with the machine.
-
Page 2: Table Of Contents
..................IP21 ..............................ES11 ....................................................................................................................EC1 ..............................Contact Information Wilbur Curtis Co., Inc. 6913 Acco Street | Montebello, CA 90640 US Phone: 323-837-2300 | Toll Free: 800-421-6150 Email: csrassistance@wilburcurtis.com | Web: www.wilburcurtis.com . - 4:00 . PT Email: techsupport@wilburcurtis.com 070120A... -
Page 3: Fs7
27.36” 10.11” 22.82” 41.0 lbs 6.28 cu. ft. 20 - 90 psi 1.0 gpm G4TBS [69.5 cm] [25.7 cm] [58.0 cm] [18.6 kg] [0.18 m [138 - 620 kPa] [3.8 lpm] • • • • G4TBS, KEY FEATURES/SPECS/SYSTEM REQUIREMENTS 092419B... -
Page 4: Is2
INSTRUCTIONS could result in personal injury or void the warranty. • This appliance is designed for commercial use. Any service other than cleaning and preventive maintenance should be performed by an authorized Wilbur Curtis service technician. • serviceable parts inside. - Page 5 IMPORTANT SAFEGUARDS CE Requirements • This appliance must be installed in locations where it can be overseen by trained personnel. • • This appliance is not suitable for outdoor use. • • • This appliance must not be cleaned by water jet. •...
-
Page 6: Ii2
INSTALLATION INSTRUCTIONS WARNING: WARNING: Improper electrical connection may result in an electric shock hazard or damage the unit. This appliance must be properly grounded. NOTICE: DO NOT connect this appliance to a hot water supply. The water inlet valve is not rated for hot water. -
Page 7: Ii8
INSTALLATION INSTRUCTIONS Installation Leveling WARNING: Use the leveling legs to level the brewer only. Do not use them to adjust brewer height. Do not extend them higher than necessary. Position the brewer on the countertop. Level it left to right and front to back by turning the bottom of the legs. - Page 8 INSTALLATION INSTRUCTIONS Connect the Brewer Wiring (cont.) 11 If the power cord will be connected directly to the junction box, connect the power cable wires to the terminals in the junction box. See the ELECTRICAL SCHEMATIC for the power supply requirements. WARNING: Turn off power to the junction box at the circuit breaker panel before connecting the power cable to the brewer.
- Page 9 INSTALLATION INSTRUCTIONS Power Up the Brewer (cont.) 16 Make sure that the circuit breaker supplying power to the unit is on. 17 Turn the toggle switch on the back of the brewer to the 18 When the water in the tank rises to the correct level, the heating elements will turn on automatically.
-
Page 10: Oi4
OPERATING INSTRUCTIONS Brewing Instructions WARNING - TO AVOID SCALDING, AVOID SPLASHING. WARNING - The G4 Tea Brewer is factory preset for optimal performance. DISPENSER The brewer should be ON. Remove/open the lid from an empty tea dispenser and the brew basket. Fill with the switch. -
Page 11: Ci1
CLEANING INSTRUCTIONS WARNING: HOT SURFACES - To avoid injury, allow the brewer and dispenser(s) to cool before cleaning. NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives. USE OF THESE PRODUCTS WILL VOID THE WARRANTY. Cleaning The Brewer - Daily WARNING: DO NOT immerse the brewer in water or any other liquid. -
Page 12: Ci6
CLEANING INSTRUCTIONS Cleaning the Tea Dispenser (Daily) The following cleaning process requires a mild solution of dish-washing detergent and warm water, and One-Pro Handle Bonnet Container Remove the dispenser from the brewer and remove the Seat cup Wash Faucet the detergent solution and a soft bristled brush to wash Rinse Sanitize Disassemble the faucet - Unscrew the faucet assembly... - Page 13 Brew Button Control symbols - all symbols may not be present at the same time Home Undo Curtis logo Scroll Return to previous left/right Manual Programming Mode The ACCESS CODE screen will appear. The The MAIN MENU screen contains a series of sub- default pass code is 1 2 3 4.
- Page 14 PROGRAMMING GUIDE PG36 Manual Programming Mode (cont.) Tea Recipes Control Settings Brew Settings Model Select Settings Summary Exit Coffee Combo Temperature Settings By Volume Quality Timer By Time Standard-Purple Energy Savings Dilution by Volume Standard-Gray Sounds Dilution by Time Standard-Amber Diagnostics Tea/IC-1Batch Dilution Delay...
- Page 15 PROGRAMMING GUIDE PG36 Recipes Menu (cont.) Recipe Default Brew Settings Tea-Sweet and Dual-Sweet, Full Batch Temperature Tea by Volume Tea by Time Tea Dilution Volume Tea Dilution Time Tea Dilution Delay Tea Dilution Stir Standard Purple 204°F/96°C 128 oz./3.8 L 5 min.
- Page 16 PROGRAMMING GUIDE PG36 Control Settings Menu (cont.) Preventive Maintenance • Maintenance Interval - • Service Telephone Number - Brew Counter - Passwords • Programming Password - default is 1234. • Brew Password - turns the brew access password feature on and off and is used to create the brew pressed.
- Page 17 PROGRAMMING GUIDE PG36 Brew Settings Menu (cont.) Tea Dilution Stir - turns the dilution stir feature On and Off. See the Recipes settings. Tea Fast Brew - Tea Pulse Brew - routines. Tea Drip-Out - sets the Tea Drip-Out time. Drip-out allows additional time for tea to drain from the brew Sweetener Time (units equipped for brewing sweet tea only) - are 2 minutes for full batch and 1 minute for half batch.
- Page 18 PROGRAMMING GUIDE PG36 Automatic Programming - USB IMPORTANT: starting the following process. Uploading the Software to the Flash Drive as desired. Downloading the Software to the Brewer from the Flash Drive a second. Once the download is complete, the UCM will reboot so that the changes take effect. USB File Transfer FILE TRANSFER Upload...
- Page 19 ROUGH-IN DRAWINGS G4TBS - Tea Brewer 18.39 in [46.7 cm] 16.61 in 9.11 in [42.2 cm] [23.1 cm] 27.36 in [69.5 cm] 17.02 in 15.73 in 15.41 in [43.2 cm] [39.9 cm] [39.1 cm] 13.41 in [34.1 cm] 5.73 in [14.6 cm]...
- Page 20 ILLUSTRATED PARTS/RECOMMENDED PARTS Supplies and Accessories - All Models WC-29025 - Spray Head CAB-1 - Cleaning Brush Sold by the case G4TBS - Main Chassis - Exploded View See section IP21 *Orientation varies with date of manufacture G4TBS, ILLUSTRATED PARTS/RECOMMENDED PARTS 061418B...
-
Page 21: Ip7
ILLUSTRATED PARTS/RECOMMENDED PARTS G4TBS - Main Chassis - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION COVER, TOP ALPGT/D500GT/D60GT TLP/TCTS/CBS/ WC-10008 UNIVERSAL HOST ADAPTER USB WC-58117 GEMSS WC-37255 KIT, DUAL VALVE WATER INLET TRANSFORMER,120VAC-24V 4.8A W/ LEADS &... -
Page 22: Ip21
ILLUSTRATED PARTS/RECOMMENDED PARTS IP21 WC-6277/WC-75236[-20] - Tank Assembly WC-6277/WC-75236[-20] - Tank Assembly - Parts List ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION TANK, COMPLETE 1600W 120V D500GT/TCTS/ WC-5528K* KIT, WATER LEVEL PROBE, SILICONE WC-6277 PTT/CBS KIT, PROBE, ASSY WATER LEVEL W/HEX FITTING, WC-5502-01* TANK, ASSY D500GT/H/TCTS/PTT3/ CBS W/WC- O-RING &... -
Page 23: Es11
ELECTRICAL SCHEMATICS ES11 G4 TEA BREWERS (UPM) Pin Assignments 120V Hot Input 120V Hot Input Brew Valve Not Used 120V Neut ral Inlet Valve Not Used Not Used Triac Gate 10 Triac A2 11 Not Used 12 Not Used 13 Dilut ion Valve Right 14 Dilut ion Valve Left 15 Sweetner Pump 16 Sweetner Pump... - Page 24 TROUBLESHOOTING GUIDE WARNING: Electric Shock Hazard - Scald and Burn Hazard - IMPORTANT: always check all Valve Test Procedure Troubleshooting Guidelines • • • • Valve Test Procedure in either direction Water Not Hot Enough replace the temperature sensor Water Heats More Slowly Than Usual During Brewing...
- Page 25 TROUBLESHOOTING GUIDE No Power - Display Not Lit Water Tank Does Not Fill Brewer Does Not Start When Brew Button is Pressed Brewing Brewing Sensor Error Message...
- Page 26 TROUBLESHOOTING GUIDE Water Tank Does Not Fill IMPORTANT: Coffee/Tea Too Strong Dispenser Not Filled To Normal Level During Brewing Dispenser Not Filled To Normal Level During Brewing sure that the spray head is correctly aligned and that the tubing is routed properly to allow for maximum water All Of The Time...
- Page 27 TROUBLESHOOTING GUIDE No Water/Tea Flows From Brewer During Brewing Water Tank Does Not Fill Low Water Flow Warning Water Level Error Message Water Level Error Message “Internal Error 1” Message on Display “Internal Error 2” Message on Display PROGRAMMING GUIDE...
- Page 28 TROUBLESHOOTING GUIDE Water Does Not Heat At All Check to see if the water level in the tank is in contact with the water level probe. If not, see Tank Does Not Fill. • The water will not heat unless it is in contact with the probe. If the water heats, but is not hot enough, see Water Not Hot Enough.
- Page 29 Display view varies Using the Diagnostics with model The MAIN MENU Control Settings. Diagnostics Auto Test to test all circuits. If a button is highlighted green the Curtis logo DIAGNOSTICS Left Auto Test Right Dump Vavle Inlet Valve Dump Vavle Cone Lock...
-
Page 30: Ec1
ERROR CODES Warning Messages - Allows Brewer to Continue Brewing MESSAGE DISPLAY WARNING DESCRIPTION CAUSE Brew count “Gallons Since Reset” exceeds programmed Maintenance Required Maintenance Required preventative maintenance period. If the Inlet valve remains on longer than XX seconds (during the brew cycle only) and repeats TWICE during that brew Low Water Flow Low Water Flow... - Page 31 Return Merchandise Authorization (RMA): All returned equipment must be properly re-packaged in the original carton and received by Curtis within 45 days following the issuance of a RMA. NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA).