1. Manuals
  2. Brands
  3. Tach-It Manuals
  4. Label Maker
  5. Mini-Con
  6. Operation manual

Tach-It Mini-Con Operation Manual

Wipe on labeler
Hide thumbs Also See for Mini-Con:
Table of Contents

Advertisement

Quick Links

Download this manual
Operations Manual for Tach-It Mini-Con and Mini-Con-S
Wipe On Labeler with
Ben Clements and Sons, Inc. / Clements Industries, Inc.
50 Ruta Court, South Hackensack, New Jersey 07606 USA
Tel: 201-440-5500, Toll Free: 800-222-5540, Fax: 201-440-1455
Email: sales@tach-it.com, Website: www.tach-it.com
Clements Industries Japan, Clements Industries, Inc. Korea
Tach-It and Twisters are registered, copyrighted or trademarks of Clements Industries, Inc.
Copyright Ben Clements and Sons, Inc. and Clements Industries, Inc. August 2008
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mini-Con and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Tach-It Mini-Con

Summary of Contents for Tach-It Mini-Con

  • Page 1 Tel: 201-440-5500, Toll Free: 800-222-5540, Fax: 201-440-1455 Email: sales@tach-it.com, Website: www.tach-it.com Clements Industries Japan, Clements Industries, Inc. Korea Tach-It and Twisters are registered, copyrighted or trademarks of Clements Industries, Inc. Copyright Ben Clements and Sons, Inc. and Clements Industries, Inc. August 2008...

  • Page 2: Table Of Contents

    Section #4 Loading of the Labels:———————————————————————Page 5 Section #5 Operation of the Touch Panel Controller:————————————————Page 7 Section #6 Operation of the Tach-It Mini-Con and Mini-Con-S Labeler:————————Page 9 Section #7 Adjustment to the Sensitivity of the Stop Sensor:————————————–-Page 10 Section #8 Trouble Shooting:————————————————————————---Page 10...

  • Page 3: Section #1 Caution

    SECTION #2 SPECIFICATIONS: Electric Power: 115 VAC Machine Length: 57” (145cm) (includes stainless stations) Machine Width for Mini-Con: 18” (47cm) Machine Width for Mini-Con-S: 38” (96 cm) Machine Height for Mini-Con: 36” (93cm) Machine Height for Mini-Con-S: 20”...

  • Page 4: Section #3 Set Up Of The Machine

    Please note that the Mini-Con is Shown but parts are the same on the Mini-Con-S Please Identify, confirm and check each of the below main components of the Mini-Con and Mini-Con-S Labeler.  Main Label Head for Mini-Con shown for purposes of this manual. All loading and functions are the same.  Controller ...

  • Page 5: Section #4 Loading Of The Labels

    Figure #2 SECTION #4 LOADING OF LABELS: Note: In order to ensure consistent label placement unto the product, during the Label Loading process, the labels must be straight and the same distant from the body of the Main Label Head throughout the entire Label Feeding Path.
  • Page 6 SECTION #4 LOADING OF LABELS CONTINUED: 3) Verifying that the labels are feeding off the bottom of the roll, take the leading edge of the labels and bring it over A-10 Tension Roller and then in between Roller #3 and the Urethane Wiper. There is a thumb screw that will allow the Urethane Wiper to swivel out of the way, but once the labels are past this point, replace the Urethane Wiper to its original position.

  • Page 7: Section #5 Operation Of The Touch Panel Controller

    SECTION #5 OPERATION OF THE TOUCH PANEL CONTROLLER: The Touch Panel Controller (B) for the Tach-It Mini-Con and Mini-Con-S allows for full control of all functions of the Labeler. Please note that if at any time the screen of the Touch Panel Controller turns Red, there has been an error with the Labeler and it must be resolved prior to resuming work.
  • Page 8 SECTION #5 OPERATION OF THE TOUCH PANEL CONTROLLER CONTINUED: Figure #9 Using the Labeler Sub Menu: 1) From the Home Screen touch where is says Labeler and Figure #9 will appear. 2) To change the value of either the Start Delay or 2 Label Delay, touch the box which will be showing the present set value.

  • Page 9: Section #6 Operation Of The Tach-It Mini-Con And Mini-Con-S Labeler

    3) Begin to label the packages. When the pre-set Target count is completed, the screen on the Touch Panel Controller will turn Red and no more packages will be labeled. SECTION #6 OPERATION OF THE TACH-IT MINI-CON and MINI-CON-S LABELER: 1) Place the Labeler on a flat dry work surface near the proper voltage electric outlet.

  • Page 10: Section #7 Adjustment To The Sensitivity Of The Stop Sensor

    SECTION #6 OPERATION OF THE LABELER CONTINUED: 7) If any adjustments need to made to the Labeler, make the necessary adjustments. 8) The Labeler is now ready for use. SECTION #7 ADJUSTMENT TO THE SENSITIVITY OF THE STOP SENSOR (A-3): The Stop Sensor (A-3) used on this machine is designed to read the gap (die cut) between the labels.
  • Page 11 SECTION #8 TROUBLE SHOOTING CONTINUED: PROBLEM REMEDY Labels are not feeding or dispensing. Check the loading of the labels. See Section #4. The labels continue to feed after the package has past the The Stop Sensor (A-3) may need to be adjusted. See Start Sensor (A-7) Section #7.

  • Page 12: Section #9 Parts Identification

    SECTION #9 PARTS LIST:...

This manual is also suitable for:

Mini-con-s

Table of Contents