1. Manuals
  2. Brands
  3. Tach-It Manuals
  4. Label Maker
  5. Mini-Con
  6. Operation manual

Tach-It Mini-Con Operation Manual

Wipe on labeler on stand
Hide thumbs Also See for Mini-Con:
Table of Contents

Advertisement

Quick Links

Download this manual
Operations Manual for Tach-It Mini-Con Wipe On Labeler on Stand
Ben Clements and Sons, Inc. / Clements Industries, Inc.
50 Ruta Court, South Hackensack, New Jersey 07606 USA
Tel: 201-440-5500, Toll Free: 800-222-5540, Fax: 201-440-1455
Email: sales@tach-it.com, Website: www.tach-it.com
Clements Industries Japan, Clements Industries, Inc. Korea
Tach-It and Twisters are registered, copyrighted or trademarks of Clements Industries, Inc.
Copyright Ben Clements and Sons, Inc. and Clements Industries, Inc. August 2008
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mini-Con and is the answer not in the manual?

Questions and answers

Related Manuals for Tach-It Mini-Con

Summary of Contents for Tach-It Mini-Con

  • Page 1 Tel: 201-440-5500, Toll Free: 800-222-5540, Fax: 201-440-1455 Email: sales@tach-it.com, Website: www.tach-it.com Clements Industries Japan, Clements Industries, Inc. Korea Tach-It and Twisters are registered, copyrighted or trademarks of Clements Industries, Inc. Copyright Ben Clements and Sons, Inc. and Clements Industries, Inc. August 2008...

  • Page 2: Table Of Contents

    Section #4 Loading of the Labels:———————————————————————Page 5 Section #5 Operation of the Touch Panel Controller:————————————————Page 7 Section #6 Operation of the Tach-It Mini-Con Labeler:———————————————Page 9 Section #7 Adjustment to the Sensitivity of the Stop Sensor:————————————–-Page 10 Section #8 Trouble Shooting:————————————————————————---Page 10...

  • Page 3: Section #1 Caution

    SECTION #1 CAUTION:  Before operating the machine, read the complete operator manual.  Never have the power on this machine plugged into the power supply when any of the covers of the machine have been removed.  Install and operate this machine only on a flat, level and dry surface. ...

  • Page 4: Section #3 Set Up Of The Machine

    SECTION #3 SET UP OF THE MACHINE: Please Identify, confirm and check each of the below main components of the Mini-Con Labeller.  Main Label Head  Controller Figure #1  Adjustable Height Stand Label Roll Label Head Control Box...

  • Page 5: Section #4 Loading Of The Labels

    Figure #2 SECTION #4 LOADING OF LABELS: Note: In order to ensure consistent label placement unto the product, during the Label Loading process, the labels must be straight and the same distant from the body of the Main Label Head throughout the entire Label Feeding Path.
  • Page 6 SECTION #4 LOADING OF LABELS CONTINUED: 3) Verifying that the labels are feeding off the bottom of the roll, take the leading edge of the labels and bring it over A-10 Tension Roller and then in between Roller #3 and the Urethane Wiper. There is a thumb screw that will allow the Urethane Wiper to swivel out of the way, but once the labels are past this point, replace the Urethane Wiper to its original position.

  • Page 7: Section #5 Operation Of The Touch Panel Controller

    SECTION #5 OPERATION OF THE TOUCH PANEL CONTROLLER: The Touch Panel Controller (B) for the Tach-It Mini-Con allows for full control of all functions of the labeller. Please note that if at any time the screen of the Touch Panel Controller turns Red, there has been an error with the labeller and it must be resolved prior to resuming work.
  • Page 8 SECTION #5 OPERATION OF THE TOUCH PANEL CONTROLLER CONTINUED: Figure #9 Using the Labeller Sub Menu: 1) From the Home Screen touch where is says Labeller and Figure #9 will appear. 2) To change the value of either the Start Delay or 2 Label Delay, touch the box which will be showing the present set value.

  • Page 9: Section #6 Operation Of The Tach-It Mini-Con Labeler

    1) Place the Mini-Con Labeller on a flat dry work surface near the proper voltage electric outlet. 2) Set up the Mini-Con Labeller and load the labels into the Labeller per the instructions in Sections 3 & 4 of this manual.

  • Page 10: Section #7 Adjustment To The Sensitivity Of The Stop Sensor

    SECTION #6 OPERATION OF THE TACH-IT MINI-CON LABELER CONTINUED: 7) If any adjustments need to made to the labeller, make the necessary adjustments. 8) The labeller is now ready for use. SECTION #7 ADJUSTMENT TO THE SENSITIVITY OF THE STOP SENSOR (A-3): The Stop Sensor (A-3) used on this machine is designed to read the gap (die cut) between the labels.
  • Page 11 SECTION #8 TROUBLE SHOOTING CONTINUED: PROBLEM REMEDY Labels are not feeding or dispensing. Check the loading of the labels. See Section #4. The labels continue to feed after the package has past the The Stop Sensor (A-3) may need to be adjusted. See Start Sensor (A-7) Section #7.

  • Page 12: Section #9 Parts Identification

    SECTION #9 PARTS LIST:...

Table of Contents