Summary of Contents for Primera DX850e
-
Page 1: Table Of Contents
Unpacking and Setup Loading the Label Stock Dispensing the Label Using the Control Panel Label Path Diagram Troubleshooting and Maintenance 13 © 2011 All rights reserved For the most recent version of this manual please Specifications visit http://primera.eu/europe/manuals.html... - Page 2 Notices: The information in this document is subject to change without notice. NO W ARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No liability is assumed for err ors contained herein or for incidental or consequential damages in connectio n with the furnishing, performance, or use of this material.
-
Page 3: Unpacking And Setup
Section 1: Unpacking and Setup Thank you for purchasing the DX850e Label Dispenser (hereafter referred to as “Label Dispenser“). The Label Dispenser includes a Power Cor d, 12 volt Power Adapter and the parts shown in Figure 1-1. The Roll Bar, Roll Guides and Roll Drag Arm are located in the supply box along with the Power Cord. -
Page 4: Loading The Label Stock
Tip! For smaller diameter label roll cores you may need to reverse the Roll Guides so that the bottom of the guides are facing out to allow the uprights to be placed next to the roll. 4 DX850e Label Dispenser... - Page 5 5. Place the removed Roll Guide back on the Roll Bar and slide it close to, but not touching the label stock roll. (Figure 2-4.) Figure 2-4. Tip! Roll Guide Uprights must not pinch the label stock roll. (The label stock roll must have free- play between guides.) DX850e Label Dispenser 5...
- Page 6 Roller should be in the unclamped position. (See Figure 2-10 for a detailed diagram of the Liner Idler Roller positions.) Figure 2-6. Note: This procedure assumes that the first 6 inches of labels will not be dispensed using the Label Dispenser. Of course, you may still peel these labels by hand. 6 DX850e Label Dispenser...
- Page 7 Note: The liner may be fed out the front or back of the Label Dispenser. 10. Push the Liner Idler Roller into the clamped position by pr essing your thumbs on the Liner Idler Roller Tabs on both sides. (Figure 2-8.) Figure 2-8. DX850e Label Dispenser 7...
- Page 8 11. Move the Label Sensor Bracket wher e desired within the width of the label. (Figure 2-9.) Figure 2-9. 12. You are now ready to dispense labels. 8 DX850e Label Dispenser...
-
Page 9: Dispensing The Label
2. To Start dispensing press the Start/Stop button on the Contr ol Panel. (Figure 3-2.) Figure 3-2. Start/ Counter Stop Reset DX850e Label Dispenser 9... - Page 10 5. When you are ready to stop dispensing labels or if you want to stop for another r eason such as adjusting the label sensor position, simply pr ess the Start/Stop Button. 6. To remove the label stock, disengage the Liner Idler Roller by pulling back on the tabs. 10 DX850e Label Dispenser...
-
Page 11: Using The Control Panel
“LED”. Then pr ess the + or – buttons to adjust the LED intensity . 2. Half-Speed Mode: To start system in Half-Speed Mode for wide label stock: Pr ess and hold the – Button during power-up. DX850e Label Dispenser 11... -
Page 12: Label Path Diagram
Section 5: Label Path Diagram Label Path Diagram Label Path Liner Drive Roller Liner Idler Roller Peel Edge Front or Rear Liner Output 12 DX850e Label Dispenser... -
Page 13: Troubleshooting And Maintenance
Liner Drive Roller . Lubricate bearings. Primera recommends oiling the four bearings associated with the Liner Drive Roller and Liner Idler Roller. Oil these four bearings for every 50,000 labels dispensed. They should only be oiled after the first 50,000 labels as they ar e lubricated with a special grease at the factory. -
Page 14: Specifications
2 in/sec. in Half-speed Mode for 6-8“ wide labels See Section 4. Agency certifications: UL, UL-C, CE, FCC Class B Weight: 11.5 lbs (5.2 kg) Dimensions: 13.44“ W x 8.75“ H x 11.25“ D (341mm W x 222mm H x 2876mm D) 14 DX850e Label Dispenser... - Page 16 P/N 511260 - 201011...