Panasonic TH-65PB1U Operating Instructions Manual page 57

Item
Locks the input switch operation.
Off
*1 "SLOT INPUT" is displayed when an optional Terminal Board is installed.
*2 "COMPONENT" may be displayed as "RGB" depending on the setting of "COMPONENT/RGB-IN SELECT".
Input lock
Notes:
• Only the adjusted signal is displayed (see page 18).
• Input switch can be used when this is set to "Off".
Off
Off: All the buttons on main unit can be used.
MENU&ENTER: Locks
On: Locks all the button on main unit.
Button lock
Sets Button lock with the unit buttons in the following procedure.
Off: Press
MENU&ENTER: Press
On: Press
Off
Off:
User1: You can only use
Remocon User level
User2: You can only use
User3: Locks all the buttons on remote control.
Enable:
Disable: Disables the "Off-timer function".
Off-timer function
Note: When "Disable" is set, the Off-timer is cancelled.
Normal
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Initial Power Mode
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Remote ID" or "Serial ID".
Set value range: 0 - 100
ID select
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off:
On:
Remote ID
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and
Sets the panel ID Control.
Off:
Serial ID
On:
Adjusts the image display size on screen.
Off:
On:
Notes:
Display size
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (Video)
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when digital zoom, Multi display or Portrait display is selected.
• When "Display size" is set to "On", "H-POS" and "V-POS" in "POS./SIZE" can be adjusted.
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
SLOT INPUT* 1 VIDEO
When a Terminal Board with dual input terminals is installed, "SLOT INPUT A" and "SLOT INPUT B" are displayed.
(see page 52)
MENU&ENTER
and
MENU
four times Press
four times Press
ENTER/
four times Press
User1 User2
You can use all of the buttons on the remote control.
,
Enables the "Off-timer function".
Standby
Power returns in power On. (Power Indicator : green)
Disables ID remote control functions. You can use normal remote control operations.
Enable ID remote control functions.
display unit. About the setting method, please refer to "ID Remote Control Function" (see page 49)
and "ID select" (above-mentioned).
Disables external control by the ID.
Enables the external control by the ID.
Sets the normal image display size on screen.
Sets the image display size approximately 95 % of the normal image display.
Off
Adjustments
COMPONENT*
On
buttons on main unit.
ENTER/
four times Press
INPUT
four times Press
four times Press
ENTER/
User3
, , , buttons on the remote control.
button on the remote control.
On
On
Options Adjustments
2 HDMI DVI PC
four times Press
ENTER/
four times Press
INPUT
four times Press
ENTER/
NETWORK
ENTER/
57