Summary of Contents for Fanimation Old Havana FPH210
Page 1
Series Fans Motor Ass'y with Ceiling Fan Ac ces so ry Weight 22 lbs Motor As sem bly #FPH210 Weight 19 lbs Motor Ass'y with Wall Accessory Weight 27 lbs Motor Ass'y with Pedestal Ac ces so ry Weight 29 lbs...
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation. 7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
Page 3
Fanimation. or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. 1. Check to see that you have received the following parts: •...
Page 4
Fanimation. or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. 1. Check to see that you have received the fol low ing...
Page 5
How to Assemble the Ceiling Accessory NOTE: Proceed to page 8 for Assembly Instructions if you have purchased a Floor/Desk Model, page 10 for Pedestal Model Assembly Instructions and page 12 for Wall Mount Model Assembly Instructions. Prior to assembly, set aside and save the hardware bag packed in the upper foam packing.
Page 6
How to Assemble the Ceiling Accessory (cont'd) 10. Remove the ¼˝ rod and thread the third ¼-20 x 1½˝ allen head bolt into this hole. 11. Tighten the 3 allen head bolts. 12. Pass the Downrod / Hanger Ball Assembly through the top of the ceiling canopy and push the bell shaped motor coupling cover onto the downrod as shown.
Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 6 depicts different structural configurations that may be used for mounting the outlet box.
How to Hang Your Ceiling Fan (cont'd) 3. Carefully lift the fan and seat the downrod/hanger ball assembly on the hanger bracket that was just attached to the outlet box (Fig. 8). Be sure the groove in the ball is lined up with tab on the hanger bracket (Fig. 8). 4.
Page 9
How to Wire Your Ceiling Fan (cont'd) ▲WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. operate fan until all parts are assembled. Noise and fan damage could result.
Page 10
Fanimation. or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. 1. Remove Floor / Desk base from carton.
Page 11
How to Assemble Your Floor / Desk Fan 1. After removing the Floor/Desk base from the carton, place it on the floor with the flat surface resting on the floor. Floor / Desk Base Fig. 13 2. Install Hex Bolt and washer in Floor / Desk base. 3.
Page 12
Fanimation. or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. NOTE: Column is not included and is sold seperately.
How to Assemble Your Pedestal Fan 1. Assemble Column to floor base using 15/16˝-18 x 1½˝ bolt and washer (Fig. 18). Do not overtighten. 2. After you assembly the column to the floor base, you will proceed to mounting your Motor Assembly to the column.
Page 14
Fanimation. or accessories not designated for use with this product by Fanimation could result in personal injury or property damage. Contact your retail store for missing or damaged parts. 1. Check to see that you have received the fol low ing parts: •...
Page 15
Mounting Wall Bracket to Wall 1. Determine approximate position of fan. 2. Locate stud in your wall. 3. For stud installation the top and bottom holes on wall bracket will be used. These holes are on 11” centers. 4. Position wall bracket on dry wall and mark hole locations.
Page 16
Using Your Wall Fan 1. Your fan is now ready to operate. 2. Plug the fan into a U.L. approved 120 volt outlet. Fig. 25 Operating Your Wall Fan 1. Check the operation of the fan by turning the speed control to “high”. 2.
Maintenance Periodic cleaning of your fan is the only main te nance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Page 18
MOTOR ASSEMBLY MODEL # FPH210_ _ Item # Description Motor Assembly CEILING FAN ACCESSORY MODEL # FPH81_ _ Item # Description Ceiling Canopy / Hanger Bracket Assembly Hanger Bracket Ceiling Canopy Knurled Knobs (2) 5/32˝ Threaded Rods (2) 5/32˝ External Lockwasher (2) Motor Coupling Cover 6˝...
Page 20
MOTOR ASSEMBLY MODEL # FPH210_ _ Item # Description Motor Assembly FLOOR / DESK ACCESSORY MODEL # FPH41_ _ Item # Description Floor / Desk Base Standard Hardware Bag 5/16˝-18 x 2½˝ Bolt 5/16˝ Flat Washers (3) Special Hex Bolt 5/16˝-18 x 1½˝...
Page 21
MOTOR ASSEMBLY MODEL # FPH210_ _ Item # De scrip tion Motor Assembly PEDESTAL ACCESSORY MODEL # FPH21_ _ Item # Description Floor Base Pedestal Column (optional) Standard Hardware Bag 5/16˝-18 x 2½˝ Bolt 5/16˝ Flat Washers (3) Special Hex Bolt 5/16˝-18 x 1½˝...
Page 22
MOTOR ASSEMBLY MODEL # FPH210_ _ Item # Description Motor Assembly WALL MOUNT ACCESSORY MODEL # FPH61_ _ Item # Description Wall Bracket Standard Hardware Bag 5/16˝-18 x 2 ½˝ Bolt 5/16˝ Flat Washers (3) Special Hex Bolt 5/16˝-18 x 1½˝ Bolt (for use with Pedestal Accessory only) Wall Unit Hardware Bag #12 x 3˝...
Page 23
Changing the Motor Assembly Position These instructions apply to all four fan models. 1. Loosen 5/16-18 x 2½˝ bolt (Item #22) on Motor Assembly. Position Motor Assembly to desired po si tion and retighten bolt (Fig. 27) Fig. 27 2. The fans will not os cil late. To swivel the direction of the Mo tor As sem bly follow the in struc tions be low.