Environmental Protection - Swann CURING LIGHT Instruction Manual

Conducted RF 3 Vrms
GB/T 150 kHz to 80
17626.6 MHz
Radiated RF 3 V/m
GB/T 80 MHz to 2.5
17626.3 GHz
NOTE: 1 At 80 MHz end 800 MHz the higher frequency range applies.
NOTE: 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically
with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which the models Curing Light are
used exceeds the applicable RF compliance level above, the model Curing Light should be observed to verify
normal operation. If abnormal performance is observed, additional measures may be necessary, such as reori-
enting or relocating the models Curing Light.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3V/m.
The Rated maximum
output power of
the transmitter
W
0.01
0.1
1
10
100
For the maximum rated output power of the transmitter not listed in the above table, the recommended separa-
tion distance (d) which in meters (m) that can be determined by the formula in the frequency column of the cor-
responding transmitter. The P is the maximum rated output power of the transmitter provided by the transmitter
manufacturer which in watts (W).
Note 1: At 80MHz and 800MHz frequency points, the higher frequency band formula is used.
Note 2: These guidelines may not be suitable for all situations. Electromagnetic propagation is affected by the
absorption and reflection of buildings, objects and human bodies.

10. Environmental protection

Components
Main units
Charging base
Adaptor
Mechanical element (Including screws, nuts, joint rings, etc.)
○: Indicates that the content of this toxic and hazardous substance in all homogeneous materials of this
component is below the limit requirement in SJ/T-11363-2006 "Limit Requirements for Toxic and Hazardous
Substances in Electronic Information Products".
×: It means that the content of this toxic and hazardous substance in at least one of the homogeneous
materials of the part exceeds the limit requirement of SJ/T11363-2006. (This product complies with EU RoHS
environmental protection requirements; currently there is no mature technology in the world that can replace or
reduce the lead content in electronic ceramics, optical glass, steel and copper alloys)
According to the "Administrative Measures for Restricting the Use of Hazardous Substances in Electrical and
Electronic Products", "Regulations for Recycling and Disposal of Waste Electrical and Electronic Products" and
relevant standards, please comply with the safety and use precautions of the products, and recycle or dispose of
the products in appropriate ways according to local laws and regulations after the use of the products.
3 Vrms
3 V/m
The distance between different frequencies of the transmitter
150kHz to 80MHz
d=1.2×P1/2
0.12
0.38
1.2
3.8
12
Portable and mobile RF communications equipment should
be used no closer to any part of the models Curing Light,
including cables, than the recommended separation distance
calculated from the equation applicable to the frequency of the
transmitter.
Recommended separation distance
1/2
d=[3,5/V1]×P
1/2
d=[1.2/E1]×P 80 MHz to 800 MHz
1/2
d=[2.3/E1]×P 800 MHz to 2.5 GHz
Where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and d Is
the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by
an electromagnetic site survey,
pliance level in each frequency range
Interference may occur In the vicinity of equipment marked
with the following symbol:
80MHz to 800MHz
d=1.2×P1/2
0.12
0.38
1.22.3
3.8
12
hazardous substance or element
(Pb)
○
○
○
○
7
a
should be less than the com-
800MHz to 2,5GHz
d=2.3×P1/2
0.23
0.73
2.3
7.3
23
(Hg) (Cd) (Cr6+) (PBB) (PBDE)
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○
○
○
○