Default Setting Values - Emerson XR75CX Installation And Operation Manual

19 Default Setting Values

Label
SEt Setpoint
rtc* Real time clock menu
Hy Differential
LS Minimum setpoint
US Maximum setpoint
ot Thermostat probe calibration
P2P Evaporator probe presence
oE Evaporator probe calibration
P3P Third probe presence
o3 Third probe calibration
P4P Fourth probe presence
o4 Fourth probe calibration
Ods Outputs delay at start up
Ac Anti-short cycle delay
rtr P1-P2 percentage for regulation
CCt Continuous cycle duration
CCS Setpoint for continuous cycle
Con Compressor ON time with faulty probe
CoF Compressor OFF time with faulty probe
CF Temperature measurement unit
rES Resolution
Lod Probe displayed
X-REP display
2
Red
dLy Display temperature delay
dtr P1-P2 percentage for display
EdF* Kind of interval for defrost
tdF Defrost type
dFP Probe selection for defrost termination
dtE Defrost termination temperature
IdF Interval between defrost cycles
MdF (Maximum) length for defrost
dSd Start defrost delay
dFd Displaying during defrost
dAd MAX display delay after defrost
Fdt Draining time
dPo First defrost after start-up
dAF Defrost delay after fast freezing
Table 19-1 - Default Setting Values (
MODBUS Termination Blocks
Name
*
Only for models with real time clock (RTC),
Range
LS to US
-
0.1 to 25.5°C/ 1 to 255°F
-100°C to SEt/-58°F to SEt
SEt to 110°C/ SEt to 230°F
-12 to 12°C /-120 to 120°F
n = not present; Y = present
-12 to 12°C /-120 to 120°F
n = not present; Y = present
-12 to 12°C /-120 to 120°F
n = not present; Y = present
-12 to 12°C /-120 to 120°F
0 to 255 min
0 to 50 min
0 to 100 (100 = P1, 0 = P2)
0.0 to 24.0 hr
(-100 to 150.0°C) (-67 to 302°F)
0 to 255 min
0 to 255 min
°C to °F
in = integer; dE = decimal point
P1; P2
P1 – P2 – P3 – P4 – SEt – dtr
0 to 20.0 min (10 sec)
1 to 99
rtC to in
EL = electric heater; in = hot gas
nP; P1; P2; P3; P4
-50 to 50°C
1 to 120 hr
0 to 255 min
0 to 99 min
rt, it, SEt, dEF
0 to 255 min
0 to 120 min
n = after IdF; y = immediately
0 to 23 hr and 50'
2
Only for XR75CX with X-REP output)
Value Level
-5.0 ---
- Pr1
2.0 Pr1
-50.0 Pr2
110 Pr2
0.0 Pr1
Y Pr1
0.0 Pr2
n Pr2
0 Pr2
n Pr2
0 Pr2
0 Pr2
1 Pr1
100 Pr2
0.0 Pr2
-5 Pr2
15 Pr2
30 Pr2
°C Pr2
dE Pr1
P1 Pr2
P1 Pr2
0.0 Pr2
50 Pr2
rtC Pr2
EL Pr1
P2 Pr2
8 Pr1
6 Pr1
30 Pr1
0 Pr2
it Pr2
30 Pr2
0 Pr2
n Pr2
0.0 Pr2
Default Setting Values • 27