Advertisement
Quick Links
Wiring Diagram
The MVX-2004 gauges will work on
2004-2013 models except 2011-up
Softail or 2012-up Dyna. It is a direct
plug in on these models and requires
no additional wiring. Auxiliary
indicators can be wired to the gauge.
IMPORTANT NOTE!
100 miles (160km) of operation. See "preset odometer" for instructions.
Mounting:
The MVX-2004 is designed to fit in the "Fat Bob" style five inch diameter dash mount gauge openings.
For all models except Deuce
NOTE: The supplied ABS mounting ring is not used for these applications and can be discarded
L-Bracket (supplied)
TANK MOUNT SPEEDOMETER/TACHOMETER
This gauge has an odometer preset option that is only available for the first
Dakota Digital Gauge
MVX-2004
Factory Gasket
1
MODEL MVX-2004
Factory Dash Panel
#8 Lock Washer
8-32 x ½" Screw
MAN#650477:D
Advertisement
Related Manuals for Dakota Digital MVX-2004
Summary of Contents for Dakota Digital MVX-2004
- Page 1 100 miles (160km) of operation. See “preset odometer” for instructions. Mounting: The MVX-2004 is designed to fit in the “Fat Bob” style five inch diameter dash mount gauge openings. For all models except Deuce NOTE: The supplied ABS mounting ring is not used for these applications and can be discarded...
- Page 2 Since the Deuce gauge mounts from under the dash, mounting requires use of the supplied ABS bracket. Factory Dash Mounting Tabs (cast in Panel dash) Factory Bezel Gasket Dakota Digital Gauge MCL-2004 (-R) New Mounting Bracket (supplied) #8 Lock Washer 8-32 x ½” Screw MAN#650477:D...
- Page 3 Remove the rubber gasket from the factory gauge bezel. • Fit the gasket over the bezel of the Dakota Digital gauge. The gasket doesn’t cover the entire bezel; there should be some bezel showing on the front as well as the rear.
- Page 4 OPTIONAL OIL PRESSURE Dakota Digital part number SEN-1039 must be used. The sensor red wire connects to the gauge white/red wire, the sensor white wire connects to the gauge gray wire, and the sensor black wire connects to the gauge black wire.
-
Page 5: Function Switch
FUNCTION SWITCH The factory speedometer push button switch is used as the main function switch. The function switch allows access to all of the mileage, RPM, and performance information. Pressing and releasing the function switch toggles through the different displays. Pressing and holding the switch for about two seconds will switch the focus between the speed message display and tach message display. - Page 6 GAUGE SETUP AND CALIBRATION The function switch is used to enter setup mode for all of the gauges. All of the setup is done from the speedometer message display. To get into setup, press and hold the function switch while turning the key on. Press and release the switch to advance through the menus below, when on the desired option press and hold the switch to select setup for that particular gauge/function.
- Page 7 Press and hold the switch while turning the key on. The speedometer will show the current revision code. Release the switch. Press and release the switch to move through the different setup menus. Press and hold the switch to select a menu option. Diag code Diagnostics mode for checking/clearing trouble codes •...
- Page 8 tach Tachometer warning setup • Press and release the switch until “tach” is displayed, then press and hold the switch until the display blanks. • Release the switch. The display will show “hi”, the current rpm warning (2200 – 8200), and “warning”. •...
- Page 9 • Release the switch. The display will show “LO”, the current warning (9.0 – 12.1), and “warning”. • Press and release the switch to change the value, press and hold the switch to select it. MAN#650477:D...
- Page 10 oil psi Engine oil temperature setup menu • Press and release the switch until “oil psi” is displayed, then press and hold the switch until the display blanks. • Release the switch. The display will show “ON” or “OFF” depending on whether the reading is currently enabled. •...
-
Page 11: Troubleshooting Guide
Any action for breach of any warranty hereunder, including any implied warranty of merchantability, must be brought within a period of 24 months from date of original purchase. No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with the sale of this product.