Traveling (Driving); Parking And Stowing; Platform Loading - JLG Commander CM1432 Operators & Safety Service & Maintenance Illustrated Parts Manual

JLGSizzor
SECTION 4 - MACHINE OPERATION
JLGSizzor
Notes
Some machines built before August 1992 and all
machines built after August 1992 are equipped with an
ENABLE switch on the side ofthe platform control box.
This switch must be depressed before activating
DRIVE, LIFT, or STEER functions from the platform
control box.
DRIVE function is cut-out when platform Is raised
above 17 feet (5.2 meters) on Models CM2033 and
CM2046, or when platform is raised above 21 feet (6.4
meters) on Models CM2546 and CM2558. Model
CM1432 is not equipped with a DRIVE cu--out.
b. Traveling Forward:
(1 ). If m.achine is shut down, turn Battery or
Emergency Stop switch at Ground Control
Station to ON position.
(2). Place Platform/Ground Select or Power
Selector switch at ground control to PLAT-
FORM.
(3).
If machine is not equipped with a PQ con-
troller, position Drive Motor Speed switch
to desired position and position Drive
switch to FORWARD and hold for duration
of travel. If machine is equipped with
Enable switch, Enable switch must be
depressed before activating DRIVE func-
tion.
(4). If machine is equipped with a PQ control-
ler, position control handle to FORWARD
and hold for duration of travel. Drive speed
is determined by the distance the control
handle is moved from the center off posi-
tion. If machine is equipped with Enable
switch, Enable switch must be depressed
before activating DRIVE function.
b. Traveling in Reverse.
(1 ).
If machine is shut down, turn Battery or
Emergency Stop switch at Ground Control
Station to ON position.
(2). Place Platform/Ground Select or Power
Selector switch at ground control to PLAT-
FORM.
(3). If machine is not equipped with a PQ con-
troller, position Drive Motor Speed switch
to desired position and position Drive
switch to REVERSE and hold for duration
of travel. If machine is equipped with
Enable switch, Enable switch must be
depressed before activating DRIVE func-
tion.
(4).
If machine is equipped with a PQ control-
ler, position control handle to REVERSE
and hold for duration of travel. Drive speed
is determined by the distance the control
handle is moved from the center off posi-
tion. If machine is equipped with Enable
switch, Enable switch must be depressed
before activating DRIVE function.
4-8. PARKING AND STOWING.
Note
When parking battery-powered units overnight, bat-
teries should be charged in accordance with Instruc-
tions in Section 2 to ensure readiness for the following
workday.
Park and stow machine as follows:
a. Drive machine to a reasonably well-protected
and well-ventilated area. ·
b.
Ensure platform is fully lowered.
c.
Position Battery or Emergency Stop switch to
OFF position.
d. If necessary, cover the instruction placards,
caution and warning decals so that they will be
protected from. hostile environment.
e.
Chock at least two wheels when parking
machine for an extended period of time.
f.
Turn Platform/Ground Select or Power Selector
switch to OFF and remove key to disable
machine from unauthorized use.
4-9. PLATFORM LOADING.
CAUTION.
MACHINE IS . EQUIPPED WITH . OVERLOAD
PROTECTION SYSTEM THAT CUTS OUT ALL
MACHINE FUNCTIONS WHEN PLATFORM IS
LOADED TO 120% OF RATED CAPACITY.
MACHINE FUNCTIONS ARE RESTORED WHEN
OVERLOAD CONDITION IS CORRECTED.
a. The platform maximum rated load capacity is
shown on a placard located on the platform and
is based upon the following criteria.
(1). Machine is positioned on a smooth, firm
and level surface.
(2). All braking devices are engaged.
(3). Maximum capacity for each model is as
follows:
CM1432- 500 lb. (227 kg)
CM2033 - 750 lb. (340 kg)
CM2046 - 1,000 lb. (454 kg)
CM2546 - 750 lb. (340 kg)
CM2558 - 1,000 lb. (454 kg)
4-4
- JLG Sizzor -