Page 6
Insert wooden dowel (A) into parts (2,12) ,then secure cam bolt (B) into parts (1,19,25) with Philips head screwdriver as per diagram.
Page 7
Insert wooden dowel (A) into parts (3,6,7,9) ,then secure cam bolt (B) into parts (4,6,7,9) with Philips head screwdriver as per diagram.
Page 8
Pick up the slider (AA) and separate the slider arm and slider bracket for the following steps. Extend the Slide .Runner all the way forward,press the plastic release lever of the slider bracket and pull out the Slider bracket complete.
Page 9
Using screw (Q) secure drawer slider (AA) to parts (17,18,23,24) with Philips head screwdriver as per diagram.
Page 10
Using screw (Q) secure drawer slider (AA) to parts (6,9) with Philips head screwdriver as per diagram.
Page 11
Using Cam lock(C) secure part (4) to part (3) ,part (7) to part (6) with Philips head screwdriver as per diagram.
Page 12
Attach part (2) to part (7),then using Cam lock(C) secure part (12) to part (6) with Philips head screwdriver as per diagram.
Page 13
Using Cam lock(C) secure parts (2,12) to part (9) ,parts (3,2) to part (3) with Philips head screwdriver as per diagram.
Page 14
Using screw (F) attach part (27) to part (13) with Hex Key (H) as per diagram.
Page 15
Using screw (F) attach part (13) to parts (3,6,9) with hex key (H) as per diagram.
Page 16
Using bolt (G) secure plastic wedge (S) into parts (14,15,16) with Hex key (H) as per diagram.
Page 17
Using bolt (G) secure plastic wedge (S) into part(16) with Hex key (H) as per diagram.
Page 18
Using bolt (G) secure plastic wedge (S) into part (13) with Hex key (H)as per diagram.
Page 19
Using bolt (U) secure Pulley (T) into part (11) ,and using bolt (K) secure Handle (J) into parts (11) with Philips head screwdriver as per diagram.
Page 20
Pick up the door (11), and fit the pulley over the slider rails on part (2) as per diagram.
Page 21
Place the plate (V) into the slider rail on the bottom panel,using screw (R) attach plate (V) to part (11) with Philips head screwdriver as per diagram. Slide the door to the left and right to make sure the door slide smoothly. If necessary adjust the screws for the door sliding smoothly.
Page 23
Using Cam lock (C) secure part (1) into parts (2,3,6,9) with Philips head screwdriver as per diagram.
Page 24
Using screw (L) secure plastic wedge (M) with Philips head screwdriver as per diagram.
Page 25
Using screw (N) attach parts (17,18) to part (20) with Philips head screwdriver ,then put part (21) as per diagram.
Page 26
Using screw (N) attach part (20) to part (22) ,then using cam lock (D) secure part (19) to parts(17,18,22) with Philips head screwdriver as per diagram.
Page 29
Place sticker (E) cover the holes as per diagram .
Page 30
Insert the assembled drawers into the unit frame, extend the Ball Bearing Slide Tracks (AA) on the pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does not go in smoothly, please take it out and repeat the step.
Page 31
Insert shelf support pin (P) into parts (3,6) as per diagram. Make sure you place the shelf support pins (P) in the same level. So the shelf is not titled .Put part (10) into unit as per diagram. Tilt and rest the adjustable shelf(10) onto the shelf support pins .
Page 32
Using screw (R) attach Velcro strap (Y) into part (1) with Philips head screwdriver as per diagram.
Page 33
Using screw (X) attach Velcro strap (Y) into Nut (Z) to wall with Philips head screwdriver as per diagram.