Control Panel - Epson Stylus Pro 7000 Series Product Information

EPSON Stylus Pro 7000 series

Control Panel

Control Panel Buttons and Functions
Button Function
Power Turns the printer on and off.
Cleaning Runs print head cleaning when pressed for
3 seconds.
Pause (Reset 3 Sec.) Stops printing temporarily. Press a second time
to resume printing.
Clears print data in the printer memory if
pressed and held for three seconds.
Returns the printer to READY status, when
pressed in SelecType mode.
SelecType Causes the printer to enter SelecType mode
when pressed in READY status.
In SelecType mode, this button can be used to
select a desired menu.
Paper Source (Item) Selects the paper source:
Cutter Off
during the ink drying process, you will need to
press Enter
In SelecType mode, this button can be used to
select an item in a menu.
Paper Feed L (+)
Feeds paper in reverse.
In SelecType mode, a desired parameter can be
selected for the item (forward order).
M
Paper Feed (–) Feeds paper forward.
In SelecType mode, a desired parameter can be
selected for the item (reverse order).
Cut/Eject (Enter) Ejects the cut sheet when the
Feeds the roll paper before cutting it when the
Roll Auto Cut
Feeds the roll paper a small amount when the
Roll Cutter Off
Feeds the roll paper and then prints a page line
below the document when the
light and
In SelecType mode, sets the selected parameter
for an item as the default value.
6 - EPSON Stylus Pro 7000 series
,
Roll Auto Cut
, or . If you press this button
Sheet
to make your setting.
light is on.
Sheet
light is on.
light is on.
Roll Cutter Off
option are on.
Print Page Line
Control Panel Lights and Messages
Normal printer operation
Message/Light
/
READY Operate
/
PRINTING Operate
flashing
INK DRY <number> MIN
light flashing
Pause
INK CHARGING
/
<number> % Operate
Pause lights flashing
TRANSPORT PREP
<number> % /
flashing
/ all lights flash briefly
RESET
PRESS PAUSE BUTTON
light on
Pause
WAIT / Pause light on or
flashing
PAUSE/ Pause
Error conditions
Message/Light
COVER OPEN /
light on
Pause
/
INK LOW Ink Out
light(s) flashing
/
INK OUT Ink Out
Roll
light(s) on
LOAD PAPER /
light on
Paper Out
LOAD ROLL
PAPER
LOAD SHEET
/
PAPER Paper
Out light on
MAINTENANCE
REQ. <error
number>
MAINTENANCE
REQ. 0100
NO INK
/
CARTRIDGE Ink
light(s) on
Out
OPTION I/F
ERROR
/
PAPER JAM
light
Paper Out
flashing
PAPER NOT CUT
light
Paper Out
flashing
8/00
Explanation
light on Printer is ready to print.
light Printer is receiving data.
/ Printer is paused to let ink dry. Wait for
the number of minutes shown.
Printer is charging the ink delivery
and system. Do not interrupt this process.
Printer is draining the ink lines to prepare
Operate light
for transportation.
Printer is resetting.
/ Press the Pause
Printer is warming up, initializing, or
charging ink.
light on Printer is paused. To resume printing,
press the
Pause
Explanation
Lower cover is open.
Ink cartridge(s) are
nearly empty (printing
continues).
Ink cartridge(s) are
empty (printing stops).
Paper set lever is down
while loading paper.
Paper source setting in
print options is different
from control panel.
A printer part will need
to be replaced soon.
The waste ink system is
almost full.
Ink cartridge(s) not
installed.
Wrong interface card
installed.
Paper has jammed in the
printer.
/ Roll paper was not cut
completely.
Cut paper did not fall off.
button to continue.
button.
Response
Close the lower cover.
Replace ink cartridge(s)
indicated by
Ink Out
light(s). See page 8.
Replace ink cartridge(s)
indicated by Ink Out
light(s). See page 8.
Pull the paper set lever up
after you load the paper.
Make sure the right
paper is loaded and the
paper source setting is
the same on the control
panel and print options.
Note the error number
and contact EPSON.
Contact EPSON to
schedule service.
Install ink cartridges as
indicated by the lights.
See page 8.
Turn off the printer and
remove the card.
Remove the jammed
paper.
Cut the paper manually,
then remove the cut
paper from the printer.
Reload paper.
Remove the cut paper
from the printer. Reload
paper.