Nominal Data; Technical Description; Mounting Data; Transport And Storage Conditions - ebm-papst W4S200-HK04-01 Operating Instructions Manual

W4S200-HK04-01

3.2 Nominal data

Motor M4S068-BF
Phase 1~
Nominal voltage / VAC 230
Frequency / Hz 50
Method of obtaining
fa
data
Valid for approval/ CE
standard
-1
Speed / min 1370
Power consumption / W 30
Current draw / A
0.21
Max. back pressure / Pa 50
Min. ambient -25
temperature / °C
Max. ambient 70
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Technical description

Weight 2.0 kg
Fan size
200 mm
Rotor surface Painted black
Blade material Sheet steel, painted black
Housing material Die-cast aluminum
Number of blades 7
Airflow direction
"V"
Direction of rotation Counterclockwise, viewed toward rotor
Degree of protection IP44; installation- and position-dependent
Insulation class "B"
Moisture (F) / H0 - dry environment
Environmental (H)
protection class
Installation position Any
Condensation None
drainage holes
Mode S1
Motor bearing Ball bearing
Touch current < 0.75 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection Thermal overload protector (TOP)
internally connected
with cable Variable
Protection class I (with customer connection of protective
earth)
Conformity with EN 60335-1; CE
standards
Approval
CCC; CSA C22.2 No. 77; EAC; UL
2111; VDE
Item no. 11272-5-9970 · ENU · Change 89188 · Approved 2016-04-18 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
1~
230

3.4 Mounting data

60
For screw clearance, see Chapter 3.1 Product drawing
fa
; Secure the screws against unintentional loosening (e.g. use self-
CE
Strength class of
screws
1590
Any further mounting data required can be taken from the product drawing.
26
0.18

3.5 Transport and storage conditions

50
-25
; Use the device in accordance with its degree of protection.
Max. permitted
80
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)

4. CONNECTION AND STARTUP

4.1 Mechanical connection

; Check the device for transport damage. Damaged devices are not to
; Install the undamaged device in accordance with your application.

4.2 Electrical connection

With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
locking screws).
8.8
+ 80 °C
- 40 °C
CAUTION
Cutting and crushing hazard when removing device
from packaging
Blades can bend
→ Carefully remove the device from its packaging, by the fan
housing. Strictly avoid shocks.
→ Wear safety shoes and cut-resistant safety gloves.
be installed.
CAUTION
Possible damage to the device
If the device slips during installation, serious damage can result.
→ Ensure that the device is securely positioned at its place of
installation until all fastening screws have been tightened.
DANGER
Voltage on the device
Electric shock
→ Always connect a protective earth first.
→ Check the protective earth.