Safety Approvals; Control Panel - Epson Stylus Photo 900 Product Information Manual

Safety Approvals

Safety standards UL 60950, CSA C22.2 No. 60950
EMC FCC part 15 Subpart B Class B
CSA C108.8 Class B
Paper
Paper Type
Single Plain, bond,
sheets and and special ink
roll paper jet papers
distributed by
EPSON
Envelopes Plain, bond, or
air mail paper
Printable area
Normal
A
B-L
Envelopes
B-L
C
A The minimum top margin is 0.12" (3.0 mm).
B-L The minimum left margin is 0.12" (3.0 mm).
B-R The minimum right margin is 0.12" (3.0 mm).
C The minimum bottom margin is 0.55" (14 mm).
* You can extend the minimum bottom margin to 0.12" (3 mm)
using the maximize (Windows) or minimize (Macintosh) margins
feature; however, print quality may decline in the expanded area.
Before printing large jobs using an extended margin setting, print
a single sheet to confirm printout quality.
** When printing with the borderless feature, print quality may
decline in the expanded area. Before printing large jobs using the
borderless setting, print a single sheet to confirm printout quality.
Note: Always load paper into the sheet feeder with the short
edge first. Load envelopes flap edge left with the flap side down.
Thickness Weight
0.003 to 0.051 inch 17 to 24 lb
(0.08 to 1.3 mm) (64 to 90 g/m
for plain bond for plain bond
paper paper
0.006 to 0.02 inch 12 to 20 lb
(0.16 to 0.52 mm) (45 to 75 g/m
Borderless**
B-R
C
A
B-R

Control Panel

To diagnose problems, check the printer's control panel, as
described below, or run a nozzle check (described on page 11).
Lights
Green power light
flashes
2
)
Red paper light
is on
Red paper light
flashes
2
)
Red paper light
flashes quickly
Red ink light
flashes
Red ink light is on
Green power light
and red ink light are
on
Green power light
is off; red paper and
red ink lights are
flashing alternately
Green power light is
off; red paper and
red ink lights are
flashing
5/03
EPSON Stylus Photo 900
Explanation
The printer is receiving a print job, replacing
an ink cartridge, charging ink, or cleaning the
print head.
Your paper ran out. Load more paper and
press the paper button.
Paper is jammed in the printer.
Press the paper button to eject the jammed
paper. If the light is still flashing, open the
cover and remove all paper, including any
jammed or torn pieces. Then reload paper and
press the paper button to continue printing.
You can also set the paper thickness lever to
the position, pull the jammed paper out,
then return the lever to the position.
If you're using roll paper, press the
paper button. If the roll paper is jammed, you
may need to remove the paper, then reload it
to continue printing (see page 7).
The paper thickness lever is set incorrectly.
Set the paper thickness lever to the correct
setting for the paper that you loaded in the
printer. See your Printer Basics book for
instructions.
One of the cartridges is low on ink. Check the
message that appears on your screen to
determine which cartridge is low or follow the
instructions on page 5. Make sure you have a
replacement cartridge.
One of the cartridges is out of ink or not
installed. Make sure you have a replacement
cartridge, then follow the steps on page 5 to
install it.
If you have just installed a new cartridge, it
may be incompatible with the printer or
incorrectly installed. Reinstall it or replace it
with the correct cartridge, as described on
page 5.
One or both of the ink cartridges is not
installed correctly. Reinstall it as described on
page 5.
Paper may be blocking movement of the print
head. Turn off the printer, then open the
cover and remove any jammed paper or other
foreign objects. Turn the printer back on
again. If the lights are still on, contact your
dealer or EPSON as described in your Printer
Basics book.
The printer may have an internal error. Turn
off the printer, wait a few seconds, and turn it
on again. If the lights are still flashing, contact
your dealer or EPSON as described in your
Printer Basics book.
EPSON Stylus Photo 900
roll
- 3