Advertisement
Step 75:
Hammer (2) Ground Stakes (DD01) into the ground next to the Tower Legs (L05) and
(L01) as shown. Secure each Ground Stake using (1) Screw (B1).
Step 76:
Hammer (2) Ground Stakes (DD01) into the ground next to the Tower Legs (L05) and
(L01) as shown. Secure each Ground Stake using (1) Screw (B1).
50
IMPORTANT SAFETY INFORMATION
ONLY REPLACE DAMAGED OR DEFECTIVE PRODUCT PARTS ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
MAINTENANCE
At the beginning of each play season:
• Tighten all hardware, but do not over-tighten to prevent splintering.
• Lubricate all metallic moving parts per manufacturer's instructions.
• Check that swing hanger bolts are secure and tight. Quick clips should be
completely closed and threaded clips screwed tight. Ropes should be
secure at both ends so they cannot loop back and create an entrapment.
• Check all protective coverings on bolts, pipes, edges and corners. Replace
if they are loose, cracked or missing.
• Check for sharp edges or protruding screw threads. Add washers if
required.
IF BOLT PROTRUDES
BEYOND T-NUT
USE AN EXTRA
FLAT WASHER
• Check ground stakes for looseness, damage or deterioration. Ensure soil
conditions are adequate to rmly hold the stakes. Firmly anchor unit to
the ground during use. Re-secure or replace if necessary.
• Check all moving parts including swing seats, ropes, cables, and chains
for wear, rust or other deterioration. Replace as needed.
• Check metal parts for rust. If found, sand and repaint using a non-lead
based paint which complies with 16 CFR 1303.
• Check all wood pieces for deterioration and splinters. Sand down
splinters and replace deteriorating wood.
• Reinstall any plastic parts, such as swing seats or any other items that
were removed for the cold season.
• Rake and check depth of loose ll protective surfacing materials to
prevent compaction and to maintain appropriate depth. Replace as
necessary.
At the end of each play season:
* Or when the temperature falls below 32º F
• Remove plastic swing seats and other items as speci ed by the
manufacturer and take indoors. Plastic components may become more
brittle in cold conditions.
• Rake and check depth of loose ll protective surfacing materials to
prevent compaction and to maintain appropriate depth. Replace as
necessary.
Owners MUST maintain the legibility of the warning labels.
THIRD PARTY ASSEMBLY
Should you elect to use a third party person or service to assemble this product, the manufacturer assumes no responsibility or liability for any
charge incurred for any assembly services. Please see our warranty for more information about damaged and missing part replacement
coverage. Little Tikes will not reimburse the customer for the price of parts purchased.
WOOD WEATHERING
Although the manufacturer has taken great care in selecting premium lumber, wood is a product of nature and is susceptible to weathering.
As the climate changes, moisture moves in and out of the wood, causing tension which can result in checking and warping.
• Checking: Surface cracks in the wood along the grain.
• Warping: Distortion from the original plane of the board. This usually happens from wetting and drying of the wood.
• Fading: A natural change in the wood color as it is exposed to sunlight. Wood may turn gray over time.
The factory-applied coating will decrease over time due to water absorption and sunlight. Apply a water repellent or stain on a yearly basis.
Most weathering is a normal result of nature and will not a ect safe and enjoyable play on this unit. If you have any concerns about
weathering, contact consumer service.
Twice a month during play season:
• Tighten all hardware, but do not over-tighten to prevent splintering.
• Check all protective coverings on bolts, pipes, edges and corners.
Replace if they are loose, cracked or missing. Check bolt covers for
sharp edges. Replace as needed.
• Check for sharp edges or protruding screw threads. Add washers if
required.
• Rake and check depth of loose ll protective surfacing materials to
prevent compaction and to maintain appropriate depth. Replace as
necessary.
• Check all moving parts including swing seats, ropes, cables, and chains
for wear, rust or other deterioration. Replace as needed.
• Lubricate all metallic moving parts per manufacturer's instructions.
Additional Maintenance:
• Check the swing beam and hardware every two weeks due to wood
expansion and contraction. It is particularly important that this
procedure be followed at the beginning of each season.
• Inspect wood parts monthly. The grain of the wood sometimes will lift
in the dry season causing splinters to appear. Light sanding may be
necessary to maintain a safe play environment. Treat your unit with
stain regularly to help prevent severe splitting and other damage.
• A waterborne transparent stain has been applied to your unit. This is
done for color only. Once or twice a year, depending on your climate
conditions, you must apply some protection (sealant) on your unit.
Prior to the application of the sealant, lightly sand any rough spots on
your unit. Please note this is a requirement of your warranty.
• Assembling and maintaining the unit on a level surface is very
important. As your children play, your unit will slowly dig its way into
the soil, and it is very important that it settles evenly. Make sure the
unit is level once each year or at the beginning of each play season.
DISPOSAL
Once you no longer desire to play with or keep the unit, it
should be disassembled and disposed of in such a way
that no unreasonable hazards exist at the time the unit is
discarded. Follow local waste ordinances.
7
Advertisement
