TYAN S5549 Manual
  1. Manuals
  2. Brands
  3. TYAN Manuals
  4. Motherboard
  5. S5549
  6. Manual

TYAN S5549 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Copyright
Copyright © 2018 MiTAC International Corporation. All rights reserved. No part of
this manual may be reproduced or translated without prior written consent from
MiTAC International Corporation.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
®
TYAN
is a trademark of MiTAC International Corporation.
®
Intel
is a trademark of Intel
AMI, AMI BIOS are trademarks of AMI Technologies.
®
Microsoft
, Windows
®
Winbond
is a trademark of Winbond Electronics Corporation.
Notice
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to printing.
MiTAC assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN
warranties relating to fitness for a particular purpose or merchantability. MiTAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MiTAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.

S5549

Version 1.0
®
Corporation.
®
are trademarks of Microsoft Corporation.
http://www.tyan.com
®
products including liability or
1

Advertisement

Table of Contents
loading

Related Manuals for TYAN S5549

Summary of Contents for TYAN S5549

  • Page 1: S5549

    Corporation and has been reviewed for accuracy and reliability prior to printing. MiTAC assumes no liability whatsoever, and disclaims any express or implied ® warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or merchantability. MiTAC retains the right to make changes to product descriptions and/or specifications at any time, without notice.

  • Page 2: Table Of Contents

    Contents S5549 ......................1 Before you begin… ..................3 Chapter 1: Instruction ................4 1.1 Congratulations ................. 4 1.2 Hardware Specifications ..............4 Chapter 2: Board Installation ..............13 2.1 Board Image ..................14 2.2 Block Diagram ................. 15 2.3 Motherboard Mechanical Drawing ........... 16 2.4 Board Parts, Jumpers and Connectors ...........

  • Page 3: Before You Begin

    The retail motherboard package should contain the following: 1 x S5549 Motherboard 1 x Rear IO shielding 1 x S5549 Quick Installation Guide 2 x SATA Single Cable IMPORTANT NOTE: Sales sample may not come with the accessory listed above.

  • Page 4: Chapter 1: Instruction

    Leveraging advanced technology from ® Intel , the S5549 is capable of offering scalable 32 and 64-bit computing, high- bandwidth memory design, and lightning-fast PCI-E bus implementation. The S5549 not only empowers you in today’s demanding IT environment but also offers a smooth path for future application upgradeability.
  • Page 5 (2) SATA-III connectors + (8) SATA SATA ports by (2) Mini-SAS (4- in-1) connectors SFP+ (4) 10GbE ports Please refer to our TPM TPM (Optional) TPM Support supported list. Chipset Aspeed AST2500 System Monitoring Total (5) 4-pin headers Temperature Monitors temperature for CPU http://www.tyan.com...
  • Page 6 Humidity RoHS RoHS 6/6 Compliant Yes Please refer to our AVL Operating System OS supported list support lists. Motherboard (1) S5549 motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables...
  • Page 7 Connector for (8) SATA ports Controller SATA Speed 6.0 Gb/s RAID Storage (1) 2280/2260/2242 (by Connector PCI-E & SATA (M.2) interface) NVMe Connector (2) SFF-8612 for (2) (OCuLink) NVMe ports Connector type (1) VGA Graphic Resolution Up to 1920x1200 http://www.tyan.com...
  • Page 8 10/100/1000 Mb/s MAC interface Brand / ROM size AMI, 32MB Hardware Monitor, PXE boot support, User Configurable FAN BIOS PWM Duty Cycle, Console Feature Redirection, ACPI sleeping states S4,S5, ACPI 6.1, SMBIOS 3.1/PnP/Wake on LAN Physical Dimension Form Factor Micro ATX http://www.tyan.com...
  • Page 9 Humidity RoHS RoHS 6/6 Compliant Yes Please refer to our AVL Operating System OS supported list support lists. Motherboard (1) S5549 motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables...
  • Page 10 (2) SATA-III connectors + (8) SATA SATA ports by (2) Mini-SAS (4- in-1) connectors SFP+ (4) 10GbE ports Please refer to our TPM TPM (Optional) TPM Support supported list. Chipset Aspeed AST2500 System Monitoring Total (5) 4-pin headers Temperature Monitors temperature for CPU http://www.tyan.com...
  • Page 11 Humidity RoHS RoHS 6/6 Compliant Yes Please refer to our AVL Operating System OS supported list support lists. Motherboard (1) S5549 motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables...
  • Page 12 Maximum Memory 2400MHz 2133MHz 2400MHz Operating Speed 1.3 - Software Specifications ® For OS (operation system) support, please check the TYAN website for the latest information. 1.4 - AST2500 User Guide ® ’s Website at Remember to visit TYAN http://www.tyan.com for AST2500 user guide.

  • Page 13: Chapter 2: Board Installation

    Caution! To avoid damaging the motherboard and associated components, do not use torque force greater than 7kgf/cm (6.09 lb/in) on each mounting screw for motherboard installation. Do not apply power to the board if it has been damaged. http://www.tyan.com...

  • Page 14: Board Image

    2.1 Board Image S5549 This picture is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above picture. http://www.tyan.com...

  • Page 15: Block Diagram

    2.2 Block Diagram S5549 Block Diagram http://www.tyan.com...

  • Page 16: Motherboard Mechanical Drawing

    2.3 Motherboard Mechanical Drawing http://www.tyan.com...

  • Page 17: Board Parts, Jumpers And Connectors

    The board you receive may not look exactly like the above diagram. The DIMM slot numbers shown above can be used as a reference when reviewing the DIMM population guidelines shown later in the manual. For the latest board revision, please visit our web site at http://www.tyan.com. http://www.tyan.com...
  • Page 18 10. ID LED (LED1) 26. ATX Power Connector 24P (PWR1) 11. IPMB Connector (J31) 27. SATA 7-Pin Connector (J29) 12. TYAN Module Header (J37) 28. SATA 7-Pin Connector (J28) 13. XDP Connector (J36) 29. USB2.0/USB3.1 Type-A (U40) 14. SGPIO Connector (J34) 30.
  • Page 19 FP_SMB_CLK FP_ID_BTN_N FP_CHASSIS_ALERT LAN2_ACT_PW FP_NMI_BTN_N LAN2_LED_ACT_N J23: Front USB3.0 Header Signal Signal USB3_INT2_PWR USB3_01_INT_RXN USB3_INT2_PWR USB3_01_INT_RXP USB3_02_INT_RXN USB3_02_INT_RXP USB3_01_INT_TXN USB3_01_INT_TXP USB3_02_INT_TXN USB3_02_INT_TXP USB2_01_INT_DN USB2_01_INT_DP USB2_02_INT_DN NC_INT_FIO_OC USB2_02_INT_DP J27: USB 2.0 Header Signal Signal USB2_IN1_PWR USB2_IN1_PWR USB2_DN1 USB2_DN2 USB2_DP1 USB2_DP2 http://www.tyan.com...
  • Page 20 DBG_HD1: TYAN Module Header (Port80 Debug Header) Signal Signal P3V3 LPC_FRAME_N LPC_LAD0 LPC_LAD1 FM_BDXDE_PLTRST_N_R LPC_LAD2 LPC_LAD3 CLK_33M_TPM LPC_SERIRQ TPM_PRSNT_N P3V3_PSU P3V3 PU_PCH_GPIO55 J31: IPMB Header Signal Signal SMB_IPMB_SDA SMB_IPMB_SCL P5V_STBY J34: SGPIO Header Signal Signal BMC_TEMP_SENSOR_SCL BMC_TEMP_SENSOR_SDA SDATAOUT0 SLOAD SCLOCK...
  • Page 21 3. Move the jumper cap to close Pin_1 and Pin_2 for several seconds to Clear CMOS. 4. Put jumper cap back to Pin_2 and Pin_3 (Default setting). 5. Reconnect power connectors to the motherboard and power on Clear CMOS system. J10: Flash security override Jumper Signal Signal FLASH_OVRD http://www.tyan.com...
  • Page 22 CPRSNTA# GROUND GROUND PERn2 PETn2 PERp2 PETp2 GROUND GROUND PERn3 PETn3 PERp3 PETp3 GROUND GROUND RESERVED P3V3 J43: ME Recovery Jumper Signal Signal TP_ME_RCVR_BOOT FM_ME_RCVR_N PD_ME_RCVR_N Pin 1-2 Closed: Normal Mode (Default) Pin 2-3 Closed: Configure Remove Cap: Recovery http://www.tyan.com...

  • Page 23: Installing The Processor And Heatsink

    2.5 Installing the Processor and Heatsink The types of processors supported by the S5549 are listed in the 1.2 Hardware Specifications section on page 4. Check our website at http://www.tyan.com ® the latest list of validated Intel processors for this specific motherboard.

  • Page 24: Tips On Installing Motherboard In Chassis

    Be especially careful to look for extra stand-offs. If there are any stand-offs present that are not aligned with a mounting hole on the motherboard, it will likely short components on the back of the motherboard when installed. This will cause malfunction and/or damage to your motherboard. http://www.tyan.com...
  • Page 25 Some chassis include plastic studs instead of metal. Although the plastic studs are usable, MiTAC recommends using metal studs with screws that will fasten the motherboard more securely in place. Below is a chart detailing what the most common motherboard studs look like and how they should be installed. http://www.tyan.com...

  • Page 26: Installing The Memory

    Memory Installation Procedure Follow these instructions to install memory modules into the S5549. Unlock a DIMM socket by Press the retaining clip outwardly in the following illustration. Align the memory module with the socket，such that the DIMM NOTCH match the KEY SLOT on the socket.
  • Page 27 Supports up to 256GB RDIMM/ 512GB LRDIMM DDR4 2133/2400 memory w/  Supports single/dual rank memory  All installed memory will automatically be detected and no jumpers or settings need changing  All memory must be of the same type and density DIMM Location http://www.tyan.com...
  • Page 28 - Use the same # of ranks per DIMM 4. Dual-rank DIMMs are recommended over single-rank DIMMs. 5. Un-buffered DIMM can offer slightly better performance than registered DIMM if populating only a single DIMM per channel. 6. Always install with DIMM_B0 Slot first. http://www.tyan.com...
  • Page 29 4GB, 8GB,16GB,32GB,64GB and 128GB Width x4/x8 Ranks Max of 8 logical ranks Channels/DIMMs Up to four channels and two DIMMs per channel Interleaving Interleaving support, within a channel, across channels and across ranks Memory Down Enabled as Statement of Work (SOW) http://www.tyan.com...

  • Page 30: Attaching Drive Cables

    2.8 Attaching Drive Cables The following illustrates how to make Cable connections. If you are in need of SATA/NVMe/Mini SAS cables or power adapters please contact your local sales representative. Attaching SATA Cables Attaching NVMe Cables Attaching Mini SAS Cables http://www.tyan.com...

  • Page 31: Installing Add-In Cards

    Doing so allows air to circulate within the chassis more easily, thus improving cooling for all installed devices. NOTE: You must always unplug the power connector from the motherboard before performing system hardware changes to avoid damaging the board or expansion device. http://www.tyan.com...

  • Page 32: Connecting External Devices

    The implementation is convenient to onsite service technicians that need to press the power button when he/she is at the rear side of the system. Please visit https://www.tyan.com to download the latest BMC firmware release and flash it to your systems.

  • Page 33: Installing The Power Supply

    2.11 Installing the Power Supply There are Two (2) power connectors on your S5549 motherboard. The S5549 supports EPS 12V power supply. PWR1: 24-Pin ATX Power Connector Signal Signal V3P3 V3P3 V3P3 -12V PS_ON# PWROK 5VSB +12V +12V V3P3 PWR2: 8-Pin ATX Power Connector...

  • Page 34: Chapter 3: Bios Setup

    Select the previous or next value/setting of the field <ESC> Exit current menu <F1> General help <F2> Previous values <F3> Load the Optimal default configuration values of the menu <F4> Save and exit <PgUp> / <PgDn> Move cursor to next/previous page http://www.tyan.com...
  • Page 35 BIOS menus are continually changing due to continual BIOS updates over the product lifespan of the motherboard. The BIOS menus provided are current as of the date when this manual was written. Please visit TYAN’s website at http://www.tyan.com for information on BIOS updates available for this specific motherboard.

  • Page 36: Main Menu

    It displays BIOS related information. Memory Information This displays the total memory size. System Date Adjust the system date. MM (Months): DD (Days): YYYY (Years) System Time Adjust the system clock. HH (24 hours format): MM (Minutes): SS (Seconds) Access Level Read only. http://www.tyan.com...

  • Page 37: Advanced Menu

    Trusted Computing Trusted Computing settings. ACPI Settings System ACPI Parameters. Onboard Device Configuration Onboard Device and Function Configuration. PCIe Slot Configuration Onboard PCIe Slot Configuration Hardware Health Configuration Monitor hardware Status AST2500 Super IO Configuration System Super IO Chip Parameters. http://www.tyan.com...
  • Page 38 Configure the iSCSI parameters Intel (R) Virtual RAID on CPU This formset allows the user to manage intel(R) Virtual RAID on CPU Tls Auth Configuration Press <Enter> to select Tls Auth Configuration All Cpu Information Display all cpu information http://www.tyan.com...
  • Page 39 3.3.1 Trusted Computing Security Device Support Enable or disables BIOS support for security device. O.S. will not show Security device. TCG EFI protocol and INT1A interface will not be available. Enabled / Disabled NOTE: Security Device Support Default is [Disabled] http://www.tyan.com...
  • Page 40 Disabled / Enabled NOTE: When Enable ACPI Auto set to [Disabled], the following menu will appear. Enable Hibernation Enable or Disables System ability to Hibernate (OS/S4 Sleep State). This option may not be effective with some operating system. Disabled / Enabled http://www.tyan.com...
  • Page 41 3.3.3 Onboard Device Configuration OnBoard VGA Enable/Disable ASPEED VGA. Disabled / Enabled ICC Clock Spread Spectrum Turn on / off Spread Spectrum Setting for IsCLK Disabled / Enabled NMI Button Enable or Disable NMI button Disabled / Enabled http://www.tyan.com...
  • Page 42 3.3.4 PCIe Slot Configuration Internal OCP Slot Select OCP Slot Bifurcation X4x4 / x8 http://www.tyan.com...
  • Page 43 Auto Fan Control must be set to [Enabled] PWM Minimal Duty Cycle menu will appear. Auto Fan Control Default setting is [Disabled]. PWM Minimal Duty Cycle PWM Minima Duty Cycle BMC Alert Beep Enable/Disable BMC Alert Beep On / Off PMBus Support PMBus Support Enabled / Disabled http://www.tyan.com...
  • Page 44 3.3.5.1 Sensor Data Register Monitoring When you enter the Sensor Data Register Monitoring submenu, you will see the following dialog window pop out. Please wait 8~10 seconds. NOTE 1: SDR can not be modified. Read only. http://www.tyan.com...
  • Page 45 http://www.tyan.com...
  • Page 46 3.3.6 AST2500 Super IO Configuration Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA) Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB) http://www.tyan.com...
  • Page 47 3.3.6.1 Serial Port 1 Configuration Serial Port Enable or disable Serial Port (COM). Enabled / Disabled Device Settings Read only. Change Settings Select an optimal setting for Super IO Device. Auto / IO=3F8h; IRQ=4; / IO=2F8h, IRQ=4; / IO=3F8h; IRQ=4; / IO=2E8h, IRQ=4; http://www.tyan.com...
  • Page 48 3.3.6.2 Serial Port 2 Configuration Serial Port Enable or disable Serial Port (COM). Enabled / Disabled Device Settings Read only. Change Settings Select an optimal setting for Super IO Device. Auto / IO=3F8h; IRQ=3; / IO=2F8h, IRQ=3; / IO=3E8h; IRQ=3; / IO=2E8h, IRQ=3; http://www.tyan.com...
  • Page 49 When set to [Fixed Time] , wake up hour Select 0-23 for example enter 8 for 3am and 15 for 3pm wake up minute Select 0-59 wake up second Select 0-59 When set to [Dynamic Time] , Wake up minute increase http://www.tyan.com...
  • Page 50 NOTE: Console Redirection Settings menu only appear when Console Redirection was set to [Enabled]. Legacy Console Redirection Legacy Console Redirection Settings Serial Port for Out-Of-Band Management/Windows Emergency Services (EMS) Console Redirection Console redirection enable or disable. Disabled / Enabled http://www.tyan.com...
  • Page 51 Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 9600 / 19200 / 38400 / 57600 / 115200 Data Bits 8 / 7 http://www.tyan.com...
  • Page 52 With this mode enabled only text will be sent. This is to capture Terminal data. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400 http://www.tyan.com...
  • Page 53 Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 9600 / 19200 / 38400 / 57600 / 115200 Data Bits 8 / 7 http://www.tyan.com...
  • Page 54 With this mode enabled only text will be sent. This is to capture Terminal data. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400 http://www.tyan.com...
  • Page 55 On Legacy OS, the Number of Rows and Columns supported redirection 80x24 / 80x25 Redirect After POST When Bootloader is selected, then Legacy Console Redirection is disabled before booting to legacy OS. When Always Enable is selected, then Legacy console Redirection is Always Enable / Bootloader http://www.tyan.com...
  • Page 56 VT100 / VT100+ / VT-UTF8 / ANSI Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 115200 / 9600 / 19200 / 57600 http://www.tyan.com...
  • Page 57 ‘start’ signal can be sent to restart the flow. Hardware flow control uses two wires to send start/stop signal. None / Hardware RTS/CTS / Software Xon/Xoff Data Bits / Parity / Stop Bits Read only. http://www.tyan.com...
  • Page 58 3.3.9 Option ROM Dispatch Policy OnBoard X722 Controller Port 0/1/2/3 OnBoard X722 Controller Port 0/1/2/3 Disabled / Enabled OnBoard Network Controller Onboard Device has: UEFI Legacy Embedded ROM(s). VIDx8086;DIOx37D2 @s0|BxB5|Dx0|Fx0 OnBoard Network Controller Onboard Device has: UEFI Legacy Embedded ROM(s). VIDx8086;DIOx37D2 @s0|BxB5|Dx0|Fx0 http://www.tyan.com...
  • Page 59 Enable or Disable Option ROM execution for selected Slot. Disabled / Enabled PCIE_5 Empty Enable or Disable Option ROM execution for selected Slot. Disabled / Enabled PCIE_6 Empty Enable or Disable Option ROM execution for selected Slot. Disabled / Enabled http://www.tyan.com...
  • Page 60 If system has SR-IOV capable PCIe Devices, this option Enables or Disables Single Root IO Virtualization Support. Enabled / Disabled BME DMA Mitigation Re-enable Bus Master Attribute disabled during Pci enumeration for PCI Bridges after SMM Locked. Enabled / Disabled http://www.tyan.com...
  • Page 61 Disabled USB Mass Storage Driver Enable/Disable USB Mass Storage Driver Support. Enabled Disabled Port 60/64 Emulation Enables I/O port 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USB aware OSes. Enabled Disabled http://www.tyan.com...
  • Page 62 AMI Virtual Device Name Mass storage device emulation type. ‘AUTO’ emuerates devices according to their media format. Optical drives are emulated as ‘CDROM’, drives with no media will be emulated. Auto / Floppy / Forced FDD / Hard Disk / CD-ROM http://www.tyan.com...
  • Page 63 3.3.12 Network Stack Configuration Network Stack Enable/Disable UEFI Network Stack Disabled / Enabled http://www.tyan.com...
  • Page 64 Network Controls the execution of UEFI and Legacy Network OpROM UEFI / Legacy Storage Controls the execution of UEFI and Legacy Storage OpROM UEFI / Legacy Video Controls the execution of UEFI and Legacy Video OpROM UEFI / Legacy http://www.tyan.com...
  • Page 65 Determines OpROM execution policy for devices other than Network, Storage, or Video UEFI / Legacy 3.3.14 iSCSI Configuration iSCSI Initiator Name The worldwide unique name of iSCSI Initiator. Only IQM format is accepted Range is from 4 to 223. http://www.tyan.com...
  • Page 66 3.3.15 Intel(R) Virtual RAID on CPU Configuration http://www.tyan.com...
  • Page 67 3.3.16 Tls Auto Configuration http://www.tyan.com...
  • Page 68 3.3.16.1 Tls Auto Configuration Enroll Cert Press <Enter> to enroll cert. Delete Cert Press <Enter> to enroll cert. http://www.tyan.com...
  • Page 69 3.3.17 All Cpu Configuration http://www.tyan.com...

  • Page 70: Platform Menu

    3.4 Platform Menu PCH Configuration Displays and provides option to change the PCH Settings Miscellaneous Configuration Miscellaneous Configuration Server ME Configuration Configure Server ME Technology Parameters http://www.tyan.com...
  • Page 71 Enable/Disable Intel(R) IO Controller Hub devices PCI Express Configuration PCI Express Configuration settings PCH SATA Configuration SATA devices and settings PCH sSATA Configuration sSATA devices and settings USB Configuration USB Configuration Settings PCH DFX Configuration PCH DFX Configuration Options http://www.tyan.com...
  • Page 72 3.4.1.1 PCH Devices Configuration Restore AC Power Loss Select S0/S5 for ACPI state after a G3 Power On / Power Off / Last State http://www.tyan.com...
  • Page 73 3.4.1.2 PCI Express Configuration PCI Express Root Port 1~20 PCI Express Root Port 1 Settings http://www.tyan.com...
  • Page 74 PCI Express L1 Substates settings. Disabled / L1.1 / L1.2 / L1.1 & L1.2 PCIe Speed Configure PCIe Speed Auto / Gen1 / Gen2 / Gen3 Max Payload Size PCIE Max Payload Size Selection MPL 128B / MPL 256B http://www.tyan.com...
  • Page 75 AHCI / RAID SATA Port 0/1/2/3/4/5/6/7 Port 0/1/2/3/4/5/6/7 Enable or Disable SATA Port Disabled / Enabled Hot Plug Designates this port as Hot Pluggable. Disabled / Enabled Configure as eSATA Configures port as External SATA (eSATA). Disabled / Enabled http://www.tyan.com...
  • Page 76 Hard Disk Drive / Solid State Drive 3.4.1.4 PCH sSATA Configuration sSATA Controller Enable or Disable SATA Controller Enabled / Disabled Configure sSATA as Indentify the SATA port is connected to Solid State Drive or Hard Disk Drive AHCI / RAID http://www.tyan.com...
  • Page 77 Otherwise all drives spin up at boot. Disabled / Enabled sSATA Device Type Identify the SATA port is connected to Solid State Drive or Hard Disk Drive Hard Disk Drive / Solid State Drive http://www.tyan.com...
  • Page 78 3.4.1.5 USB Configuration XHCI Idle L1 Enabled XHCI Idle L1.Disabled to work around USB3 hot plug will fail after 1 hot plug removal. Please put the system to G3 for the new settings to take effect. Enabled / Disabled http://www.tyan.com...
  • Page 79 Enables/Disables ADR on Host Partition Reset Enabled / Disabled Enable/Disable ADR Ti Held-off for DEBUG PURPOSE ONLY! Enabled / Disabled ADR timer expire time Select proper ADR timer value: 25uS, 50uS, 100uS or 0. 25uS / 50uS / 100 uS / 0uS http://www.tyan.com...
  • Page 80 ADR timer multiplier Select proper ADR timer multiplier: x1,8,24,40,56,64,72,80,88,96 x1 / x8 / x24 / x40 / x56 / x64 / x72 / x80 /x88 /x96 3.4.2 Miscellaneous Configuration Active Video Select active Video type Onboard Device / OffBoard Device http://www.tyan.com...
  • Page 81 3.4.3 Server ME Configuration Only Read http://www.tyan.com...

  • Page 82: Socket Configuration

    Display and provides option to change the UPI Settings Memory Configuration Displays and provides option to change the Memory Settings IIO Configuration Displays and provides option to change the IIO Settings Advanced Power Management Configuration Display and provides option to change the Power Management Settings http://www.tyan.com...
  • Page 83 This should be enabled in order to boot legacy OSes that cannot support CPUs with extended CPUID functions. Disabled / Enable Execute Disable Bit When disabled, forces the XD feature flag to always return 0. Disabled / Enabled Enable Intel(R) TXT Enables Intel(R) TXT Disabled / Enabled http://www.tyan.com...
  • Page 84 MLC Streamer Prefetcher (MSR 1A4h Bit [0]) Disabled / Enabled Adjacent Cache Prefetch MLC Spatial Prefetcher (MSR 1A4h Bit [1]) Disabled / Enabled Extended APIC Enable/disable extended APIC support Disabled / Enabled AES-NI Enable/disable AES-NI support Disabled / Enabled http://www.tyan.com...
  • Page 85 Selects the allocation size used to assign mmioh resources. Total mmioh space can be up to 32x granularity. Per stack mmioh resource assignments are multiples of the granularity where 1 unit Per stack is the default allocation. 1G / 4G / 16G / 64G / 256G / 1024G http://www.tyan.com...
  • Page 86 Numa Enable or Disable non uniform Memory Access. (NUMA) Enabled / Disabled 3.5.3 UPI Configuration Submenu UPI General Configuration Displays and provides option to change the UPI General Settings http://www.tyan.com...
  • Page 87 Enable – Set the c_L0p_en, Disable – Reset it, Auto – Auto decides based on Si Compatibility Disable / Enable / Auto Link L1 Enable Enable – Set the c_L1_en, Disable – Reset it, Auto – Auto decides based on Si Compatibility Disable / Enable / Auto http://www.tyan.com...
  • Page 88 3.5.3.2 UPI Status Configuration Submenu http://www.tyan.com...
  • Page 89 Enable – Enables DDR ECC Support. Disable – Disables this feature. Auto – Sets it to MRC default setting; current default is Enable. Disabled / Enabled Memory Topology Displays memory topology with Dimm population information Memory RAS Configuration Displays and provides option to change the Memory Ras Settings http://www.tyan.com...
  • Page 90 3.5.4.1 Memory Topology Configuration Submenu http://www.tyan.com...
  • Page 91 Mirror Enable will disable XPT Prefetch. Disabled / Enabled Memory Rank Sparing Enable/Disable Memory Rank Sparing Disabled / Enabled Correctable Error Threshold Enable/ Disable Memory Rank Sparing Patrol Scrub Enable/Disable Patrol Scrub Disabled / Enabled http://www.tyan.com...
  • Page 92 Enable/Disable PCIe Hot Plug globally. Disabled / Enabled PCIe ACPI Hot Plug Enable/Disable PCIe ACPI Hot Plug globally, or allow per-port control. When Disabled, MSI is generated on HP event. When Enabled, _HPGPE message is generated. Disabled / Enabled http://www.tyan.com...
  • Page 93 Select PCIe port Bifuncation for selected slot (s) x4x4x4x4 / X4x4x8 / x8x4x4 / x8x8 / x16 / Auto IOU1 (IIO PCIe Br2) Selects PCIe port Bifuncation for selected slot (s) x4x4x4x4 / X4x4x8 / x8x4x4 / x8x8 / x16 / Auto http://www.tyan.com...
  • Page 94 3.5.5.2 Intel® VT for Directed I/O (VT-d) Submenu Intel® VT for Directed I/O (VT-d) Enable/Disable Intel® Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI Tables. Disabled / Enabled http://www.tyan.com...
  • Page 95 3.5.5.3 Intel® VMD technology Submenu http://www.tyan.com...
  • Page 96 3.5.5.3.1 Intel® VMD for Volume Management Socket0 Submenu VMD Config for PStack 0/1/2 Intel® VMD for Volume Management D ® Enable/Disable Intel Volume Management Device Technology in this Stack. Disabled / Enabled http://www.tyan.com...
  • Page 97 Advance Power Management Configuration CPU P State Control P State Control Configuration Sub Menu, include Turbo, XE and etc. Hardware PM State Control Hardware P-State setting CPU C State Control CPU C State setting Package C State Control Package C State setting http://www.tyan.com...
  • Page 98 Max Performance / Max Efficient / Set by Intel Node Energy Efficient Turbo Energy Efficient Turbo Disable, MSR 0x1FC [19] Disabled / Enabled Turbo Mode Enable/Disable processor Turbo Mode (requires EMTTM enabled too). Disabled / Enabled CPU Flex Ratio Override Enable/Disable CPU Flex Ratio Programming Disabled / Enabled http://www.tyan.com...
  • Page 99 Disable: Hardware choose a P-state based on OS Request (Legacy P-States) Native Mode: Hardware choose a P-state based on OS guidance Out of Band Mode: Hardware autonomously choose a P-state (No OS guidance) Disabled / Native Mode / Out of Band Mode / Native Mode with No Legacy Support http://www.tyan.com...
  • Page 100 Auto / Enable / Disable Enhanced Halt State (C1E) Enables the Enhanced C1E state of the CPU, takes effect after reboot Enabled / Disabled OS ACPI Cx Report CC3/CC6 to OS ACPI C2 or ACPI C3 ACPI C2 / ACPI C3 http://www.tyan.com...
  • Page 101 3.5.5.4 Package C State Control Submenu Package C State Package C State Limit C0/C1 state / C2 state / C6(non Retention) state / C6(Retention) state / No Limit / Auto http://www.tyan.com...

  • Page 102: Server Management

    OS Watchdog Timer If enabled, starts a BIOS timer which can only be shut off by management Software after the OS loads. Helps determine that the OS successfully loaded or follows the OS Boot Watchdog Timer policy. Disabled / Enabled http://www.tyan.com...
  • Page 103 Not available if OS Boot Watchdog Timer is disabled. Do Nothing / Reset / Power Down / Power Cycle BMC Logo Enable or Disable BMC logo Disabled / Enabled System Event Log Press<Enter> to change the SEL event log configuration. BMC network configuration Configure BMC network parameters http://www.tyan.com...
  • Page 104 Choose options for reactions to a full SEL. Do Nothing / Erase Immediately Log EFI Status Codes Disable the logging of EFI Status Codes or log only error code or only progress code or both. Both / Disabled / Error Code / Progress Code http://www.tyan.com...
  • Page 105 Enable or Disable LAN1 IPV6 Support Disabled / Enabled Configuration Address source Select to configure LAN channel parameters statically or dynamically/by BIOS or BMC). Unspecified option will not modify any BMC network parameters during BIOS phase Unspecified / Static / DynamicBmcDhcp http://www.tyan.com...

  • Page 106: Security

    3.7 Security Administrator Password Set Administrator Password. User Password Set User Password. Secure Boot Customizable Secure Boot settings Security Frozen Mode Disable means Hard Drive on Non-forzen mode. Enable means Hard Drive on Forzen mode. Disabled / Enabled http://www.tyan.com...
  • Page 107 When Secure Boot control is set to 【Custom】, the following menu NOTE: will be available to be set up. Restore Factory Keys Force System to User Mode. Install factory default Secure Boot Key databases Reset To Setup Mode Delete all Secure Boot key databases from NVRAM http://www.tyan.com...
  • Page 108 Force System to User Mode. Install factory default Secure Boot Key databases. Reset To Setup Mode Delete all Secure Boot key database from NVRAM Export Secure Boot variables Copy NVRAM content of Secure Boot variable to files in a root folder on a file system device http://www.tyan.com...
  • Page 109 Enroll factory Defaults or load the keys from a file with: 1. Public Key Certificate in: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER encoded) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHA256 (bin) 2. Authenticated UEFI Variable Key: Vendor, Custom, Mixed, Test (*) modified from Setup menu http://www.tyan.com...
  • Page 110 Enroll factory Defaults or load the keys from a file with: 1. Public Key Certificate in: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER encoded) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHA256 (bin) 2. Authenticated UEFI Variable Key: Vendor, Custom, Mixed, Test (*) modified from Setup menu Set New Key Append Key http://www.tyan.com...

  • Page 111: Boot

    Continuously searches for the Legacy PXE boot image until it is found or the process is aborted (press Ctrl+Alt+Del). Disabled / Enabled Wait For “ESC” If Error Wait for “ESC” key to be pressed if error occurs. Disabled / Enabled http://www.tyan.com...
  • Page 112 Boot Option Priorities Boot Option #1/#2 Sets the system boot order. Device Name / Disabled 3.8.1 Network Device BBS Priorities Configuration Boot Option #1#2#3#4 Sets the system boot order Device Name / Disabled http://www.tyan.com...
  • Page 113 3.8.2 Delete Boot Option Configuration Delete Boot Option Sets the system boot order. Device Name / Select one to Delete http://www.tyan.com...

  • Page 114: Save & Exit

    Reset system setup without saving any changes. Save Changes Save changes done so far to any of the setup options. Discard Changes Discard changes done so far to any of the setup options. Restore Defaults Restore/Load Default values for all the setup options. http://www.tyan.com...
  • Page 115 Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. Boot Override Device Name http://www.tyan.com...

  • Page 116: Chapter 4: Diagnostics

    BIOS flash failure, you must contact your dealer for a replacement BIOS. There are no exceptions. TYAN does not have a policy for replacing BIOS chips directly with end users. In no event will TYAN be held responsible for damages done by the end user.

  • Page 117: Amibios Post Code (Aptio)

    South Bridge initialization before microcode loading 0x05 OEM initialization before microcode loading 0x06 Microcode loading 0x07 AP initialization after microcode loading 0x08 North Bridge initialization after microcode loading 0x09 South Bridge initialization after microcode loading 0x0A OEM initialization after microcode loading 0x0B Cache initialization http://www.tyan.com...
  • Page 118 Memory initialization. Configuring memory 0x2F Memory initialization (other) 0x30 Reserved for ASL (see ASL Status Codes section below) 0x31 Memory Installed 0x32 CPU post-memory initialization is started. 0x33 CPU post-memory initialization. Cache initialization CPU post-memory initialization. Application Processor(s) (AP) 0x34 initialization http://www.tyan.com...
  • Page 119 S3 Resume Progress Codes 0xE0 S3 Resume is started (S3 Resume PPI is called by the DXE IPL). 0xE1 S3 Boot Script execution 0xE2 Video repost 0xE3 OS S3 wake vector call 0xE4 – 0xE7 Reserved for future AMI progress codes http://www.tyan.com...
  • Page 120 DXEIPL was not found. DXE Core Firmware Volume was not found. Recovery failed S3 Resume failed Reset PPI is not available. DXE Phase Status Code Description 0x60 DXE Core is started. 0x61 NVRAM initialization 0x62 Installation of the South Bridge Runtime Services http://www.tyan.com...
  • Page 121 PCI Bus Hot Plug Controller initialization 0x94 PCI Bus Enumeration 0x95 PCI BUS Request Resources 0x96 PCI Bus Assign Resources 0x97 Console output devices connect 0x98 Console Input devices connect 0x99 Super IO initialization 0x9A USB initialization is started. http://www.tyan.com...
  • Page 122 0xC0 – 0xCF OEM BDS initialization codes DXE Error Codes 0xD0 CPU initialization error 0xD1 North Bridge initialization error 0xD2 South Bridge initialization error 0xD3 Some of the Architectural Protocols are not available 0xD4 PCI resource allocation error. Out of Resources http://www.tyan.com...
  • Page 123 System is waking up from the S3 sleep state. 0x40 System is waking up from the S4 sleep state. System has transitioned into ACPI mode. Interrupt controller is in 0xAC APIC mode. System has transitioned into ACPI mode. Interrupt controller is in 0xAA APIC mode. http://www.tyan.com...

  • Page 124: Appendix I: Fan And Temp Sensors

    (rpm) Temp Sensor: SAS_Air Outlet (U44). They detect the system temperature around. NOTE: The system temperature is measured in a scale defined by Intel, not in Fahrenheit or Celsius. http://www.tyan.com...
  • Page 125 BIOS Temp Sensor Name Explanation: http://www.tyan.com...
  • Page 126 Temperature of the PCH_Temp Area BIOS FAN Sensor Name Explanation CPU_FAN Fan speed of CPU_FAN FAN0 Fan speed of FAN0 FAN1 Fan speed of FAN1 FAN2 Fan speed of FAN2 FAN3 Fan speed of FAN3 FAN4 Fan speed of FAN4 http://www.tyan.com...
  • Page 127 NOTE http://www.tyan.com...

  • Page 128: Glossary

    (reading to or writing from a disk drive a single time is much faster than doing so repeatedly) there is the possibility of losing your data should the system crash. Information in a buffer is temporarily stored, not permanently saved. http://www.tyan.com...
  • Page 129 (like soundcards or keyboards) to access the main memory without involving the CPU. This frees up CPU resources for other tasks. As with IRQs, it is vital that you do not double up devices on a single line. Plug-n-Play devices will take care of this for you. http://www.tyan.com...
  • Page 130 ROM chip which can, unlike normal ROM, be updated. This allows you to keep ® ’s up with changes in the BIOS programs without having to buy a new chip. TYAN BIOS updates can be found at http://www.tyan.com ESCD (Extended System Configuration Data): a format for storing information about Plug-n-Play devices in the system BIOS.
  • Page 131 PXE (Preboot Execution Environment): one of four components that together make up the Wired for Management 2.0 baseline specification. PXE was designed to define a standard set of preboot protocol services within a client with the goal of allowing networked-based booting to boot using industry standard protocols. http://www.tyan.com...
  • Page 132 NVIDIA s (graphics communications processing units) and NVIDIA MCPs (media and processors). application Depending on the , NVIDIA SLI can deliver as much as two times the performance of a single GPU configuration. http://www.tyan.com...
  • Page 133 CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. http://www.tyan.com...

  • Page 134: Technical Support

    "TYAN's tech support is some of the most impressive we've seen, with great response time and exceptional organization in general" - Anandtech.com Help Resources: 1. See the beep codes section of this manual.
  • Page 135 (RMA) number. The RMA number Should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. ® TYAN will pay to have the board shipped back to you. Notice for the USA Compliance Information Statement (Declaration of...

Table of Contents