Table of Contents
Advertisement
Quick Links
Installation
Front view
a Inlet hose (tested to withstand
pressures up to 7000 kPa)
b Electrical connection
c Flexible drain hose (with detachable
swivel elbow)
d Control panel
11637110-01
e Detergent dispenser drawer
f Door
g Access to filter, pump and
emergency release
h Four height-adjustable feet
Advertisement
Table of Contents
Related Manuals for Miele WCA 020
Summary of Contents for Miele WCA 020
- Page 1 *INSTALLATION* 11637110-01 Installation Front view a Inlet hose (tested to withstand e Detergent dispenser drawer pressures up to 7000 kPa) f Door b Electrical connection g Access to filter, pump and c Flexible drain hose (with detachable emergency release swivel elbow) h Four height-adjustable feet d Control panel...
-
Page 2: Rear View
*INSTALLATION* 11637110-01 Installation Rear view a Drain hose e Inlet hose (tested to withstand pressures up to 7000 kPa) b Transport clips for inlet and drain f Safety caps for transit bars hoses and mains connection cable c Electrical connection g Transport clips for inlet and drain hoses and for storing transit bars d Protruding lid for holding when when not in use... - Page 3 *INSTALLATION* 11637110-01 Installation Installation surface Transporting the washing machine to its installation site A concrete floor is the most suitable installation surface. It is far less prone Danger of injury due to to vibration during the spin cycle than unsecured lid.
-
Page 4: Removing The Transit Bars
*INSTALLATION* 11637110-01 Installation Removing the right transit bar Removing the transit bars Removing the left transit bar Push the flap outwards and turn the transit bar 90° using the enclosed Push the flap outwards and turn the spanner. transit bar 90°... - Page 5 *INSTALLATION* 11637110-01 Installation Covering the holes Securing the transit bars Risk of injury from sharp edges! There is a risk of injury from reaching into holes that are not covered. To avoid the risk of injury, the holes for the transit bars must be covered after the transit bars have been removed.
- Page 6 *INSTALLATION* 11637110-01 Installation Fitting the transit bars Opening the flaps Push against the catch with a pointed object, e.g. a narrow screwdriver. The flap will open. Fitting the transit bars Install the transit bars in reverse order to their removal. Useful tip: If you lift the drum slightly, the transit bars can be pushed in more easily.
-
Page 7: Levelling The Machine
*INSTALLATION* 11637110-01 Installation Levelling the machine The washing machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used for levelling the washing machine. - Page 8 *INSTALLATION* 11637110-01 Installation Installing under a continuous Washer and dryer stack worktop A Miele tumble dryer can be stacked with the washing machine. The Risk of electric shock due to appropriate “WTV” stacking kit* to exposed cables. match your tumble dryer is required.
-
Page 9: The Miele Water Protection System
The Miele water protection housing system - Sump: Any leaking water is collected The Miele water protection system in a sump in the base of the machine. protects all parts of the washing A float switches off the water inlet... -
Page 10: Connection To The Water Supply
*INSTALLATION* 11637110-01 Installation Maintenance Connection to the water supply Only use a genuine Miele hose should Health risk and risk of damage you ever need a replacement. These are due to contaminated mains water. tested to withstand pressures up to The quality of the water used must 7000 kPa. - Page 11 For a delivery head of more than 1 m (up to a max. of 1.8 m) a replacement drain pump will need to be fitted. Please contact Miele for advice. For a delivery head of 1.8 m the hose can be extended to a length of up to a Adapter 2.5 m.
-
Page 12: Electrical Connection
If the connection cable is damaged, it must only be replaced with a specific connection cable of the same type (available from Miele) in order to avoid a hazard. For safety reasons, such replacement may only be carried out by a suitably qualified and competent technician or Miele.