Related Manuals for Canon iP4680
Summary of Contents for Canon iP4680
- Page 1 / iP4680 SIMPLIFIED SERVICE MANUAL 1. LIST OF ERROR DISPLAY 2. ADJUSTMENT / SETTINGS QY8-13BY-000 Rev.00 July 25, 2008 Canon Inc. (1/21)
-
Page 2: List Of Error Display
1. LIST OF ERROR DISPLAY 1-1. Operator Call Errors (Alarm LED Lit In Orange) Errors and warnings are displayed by the following ways: - Operator call errors are indicated by the Alarm LED lit in orange, and messages are displayed on the printer driver Status Monitor. - Page 3 Error (Blinking in Error Solution Remarks code orange) head. Faulty EEPROM data of [1405] the print head. 6 times Inner cover error. [1841 Close the inner cover, and press 1846 the Resume/Cancel button. 1851 1856 [1850 Open the inner cover, place the 1855 CD-R tray and press Resume/Cancel.
- Page 4 Failed in automatic print [2500] Press the Resume/Cancel button head alignment. to clear the error, then perform the automatic print head again. (In the iP4600 / iP4680, use Matte Photo Paper MP-101.) 13 times The remaining ink [1683] Replace the applicable ink tank The ink tank installed amount unknown.
- Page 5 1-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs) Cycles of blinking of Error Solution Error Conditions Alarm and code (Check points and replacement items) Power LEDs 2 times Carriage error [5100] An error occurred in the 1) Smearing or scratches on the carriage carriage encoder signal.
- Page 6 Cycles of blinking of Error Solution Error Conditions Alarm and code (Check points and replacement items) Power LEDs 7 times Ink absorber full [5B00, The ink absorber is 1) Ink absorber condition 5B01] supposed to be full. 2) Part replacement: - Ink absorber kit Error codes: 3) Ink absorber counter value in the...
- Page 7 Cycles of blinking of Error Solution Error Conditions Alarm and code (Check points and replacement items) Power LEDs 15 times USB Host VBUS [9000] The USB Host VBUS is 1) Part replacement: overcurrent overloaded. - Logic board 16 times Pump roller [5C20] The pump roller position 1) Cable connection sensor error...
-
Page 8: Adjustment / Settings
2. ADJUSTMENT / SETTINGS 2-1. Service Mode < Service mode operation procedures > Use the Service Tool on the connected computer. Start the printer in the service mode. With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power button. - Page 9 Name Function Remarks (1) Test Print Service test print Paper will feed from the rear tray. Service test print: - Model name - ROM version - Ink absorber counter value (ink amount in the ink absorber) - USB serial number - Destination - EEPROM information - Process inspection information...
- Page 10 - Media type: Select one from HR-101, GF-500/Office Planner, HP Bright White, and Canon Extra/STEINBEIS. 2) When printing is finished, the printer returns to be ready for selection of another function. 3) In the printout, determine the Pattern No. in which streaks or lines are the least noticeable for the LF check pattern and the Eject check pattern respectively.
- Page 11 4) In the LF/EJECT Correction section of the Service Tool, select the Pattern No. (from 0 to 4) determined in step 3) for LF and EJECT respectively, and click Set. 5) The selected LF and Eject correction values are written to the EEPROM, making the E-MIP correction value (which was set at shipment from the production site) invalid.
-
Page 12: User Mode
2-2. User Mode Function Procedures Remarks Nozzle check pattern Perform from the printer driver Set a sheet of plain paper (A4 or Letter) in printing Maintenance tab, or see the cassette, or the rear tray if selected. "Standalone printer operation" below. - Page 13 Power Operation Remarks (blinking in green) 5 times Bottom plate cleaning 2-3. Special Notes on Assembling (1) External housing removal Remove the cassette. Remove the paper support unit and the access cover. < While pushing the both sides of the paper support so that the center will warp slightly, release the left and right bosses.
- Page 14 Remove the side cover L. Remove the side cover R. (14/21)
- Page 15 Remove the front door unit. < While slightly warping the center of the paper output tray downward, release the left and right bosses. > Remove the panel cover unit (1 screw). (15/21)
- Page 16 Remove the main case unit. (16/21)
- Page 17 (2) Notes on Service Part Replacement (and Disassembling / Reassembling) Service part Notes on replacement Adjustment / settings Operation check Logic board ass'y - Before removal of the After replacement: - EEPROM information print logic board ass'y, 1) Initialize the EEPROM. - Service test print remove the power cord, 2) Set the ink absorber counter...
- Page 18 - Protect the units from soiled with ink. - Protect the housing from scratches. - For the the iP4600 / iP4680 automatic print head alignment, use Matte Photo Paper (MP-101) to ensure alignment accuracy. - Exercise caution with the screws, as follows: i.
- Page 19 (3) Paper feed motor adjustment When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by the blue arrow in the photo below). After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print operation (due to dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.
-
Page 20: Grease Application
2-4. Grease application Number of Where to apply grease / Drawing Grease Part name Grease drops x amount (mg) locations The surface where the Carriage rail Floil KG107A 270 to 330 carriage unit slides The surface where the Carriage rail Floil KG107A 18 to 36 1 x 2... -
Page 21: Notes On Transportation
2-5. Notes on Transportation This section describes the procedures for transporting the printer for returning after repair, etc. In the service mode, press the Power button to finish the mode, and confirm that the paper lifting plate of the rear tray is raised. Keep the print head and ink tanks installed in the carriage.