WARNING: TO AVOID DEATH, SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE: • Do not open the housing or attempt any repairs. In the unlikely event the unit may require service please contact Leviton Technical Support. Opening the housing or attempting to repair product will void the warranty.
GETTING STARTED Thank you for choosing LEO™ LED Zoom Ellipsoidal by Leviton . Every LEO™ LED Zoom Ellipsoidal has ® been thoroughly tested and has been shipped in perfect operating condition. Your package should include: • Light Engine • 36" - 39.5" (1m) power lead with powerCON ®...
• This product contains no user-serviceable parts. Do not open the housing or attempt any repairs, doing so will void the manufactures warranty. In the unlikely event the unit may require service please contact Leviton Technical Support. • Do not operate this product if you see damage on the housing, lenses, or cables.
PBG NEMA 5-15P connector on the other side. Other connector options are available from Leviton or may be installed by your contractor. In addition, the fixture is designed for "Feed-Thru" operation using single power source connection at the first fixture, then, using powerCON extensions ®...
CONNECT DMX LEO™ LED Zoom Ellipsoidal uses 5-pin XLR connectors for signal transmission and can be controlled via DMX-512 protocol. The diagram below shows the fixture’s XLR-5 signal ports. DMX IN LOOP XLR Pin # Signal common data - data + XLR-5 signal ports Step 1: Connect the (male) 5-pin connector side of the DMX cable to the output (female) 5-pin connector of the DMX console.
BEAM SHAPING The LEO ellipsoidal spotlight has several features which allow you to shape the beam to your needs. These features are best learned by experience and practice. The beam can be shaped using the built-in shutters, a gobo pattern, a drop-in iris, or by rotating the lens tube. The fixture also features a variable beam, altered by adjusting the front and rear zoom lenses in relation to each other.
OPERATION CAUTION: Do not touch this product’s housing during operation because it may be very hot if overheated. The maximum ambient temperature is 95˚F (35˚C). Do not operate this product at a higher temperature. Do not cover the ventilation holes when operating to avoid internal overheating. Avoid direct eye exposure to the light source while the product is on.
CONTROL BASICS CAUTION: Check the fuse before connecting power. Connect power to the powerCON connector at the rear side of LEO™ LED Zoom Ellipsoidal and switch ® the power switch to the "ON" position. The LCD display will turn on and the fixture is ready to operate. The fixture is defaulted for DMX control, press the rotary-press-knob once and rotate to move the cursor to the desired operation icon.
Page 12
SETTING SAFE OPERATION MODE CAUTION: "Live" mode allows the LED light source to operate at over-temp conditions which might shorten the lifetime and even burn out the LED chip! It is recommended to use the factory default "Safe" mode for normal operations. Repeat the steps to select the fixture Operation Mode (see figure on page 8, #5) and press once.
Page 13
CONTROL ATTRIBUTES AND DEFAULT SETTINGS The LEO™ LED Zoom Ellipsoidal fixtures have several different control attributes. With the exception of the dimming attribute which must be assigned a DMX value for remote control, all other attributes may be manually set only at the fixtures, or, remote controlled from your DMX console. Therefore, from a DMX perspective, your fixture may be a 1, 2, 3, or 4 channel fixture depending on which attributes are assigned to a channel.
DEFAULT SETTINGS Menu Items Value Default Options Level Remarks Range Value DMX Value Fan speed Option 0-50 Auto 51-100 90% of full speed 101-150 80% of full speed 151-200 70% of full speed 201-255 60% of full speed Fan speed Address 1-512 0-255...
Page 15
LENS The lens in your fixture is made of a high quality glass and reflective coating which should require little maintenance. However, due to fog residue, smoke and dust, lens cleaning must be carried out periodically to optimize light output. To maintain optimum performance and minimize wear, clean this product at least twice a month.
F.O.B. factory. Leviton is not responsible for removing or replacing equipment on the job site, and will not honor charges for such work. Leviton will not be responsible for any loss of use time or subsequent damages should any of the equipment fail during the warranty period, but agrees only to repair or replace defective equipment returned to its plant in Tualatin, Oregon.
Page 21
COMMENTS : The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitues an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed.
Need help?
Do you have a question about the LEO LED00 and is the answer not in the manual?
Questions and answers