1. Manuals
  2. Brands
  3. Northern Industrial Tools Manuals
  4. Winches
  5. 141456
  6. Owner's manual

Northern Industrial Tools 141456 Owner's Manual

12v electric winch 12,000 lbs
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1 2 V E L E C T R I C W I N C H
1 2 , 0 0 0 L B S .
OWNER'S MANUAL
WARNING:
Read carefully and understand all INSTRUCTIONS before
operating. Failure to follow the safety rules and other basic
safety precautions may result in serious personal injury.
Item# 141456

Advertisement

Table of Contents
loading

Related Manuals for Northern Industrial Tools 141456

Summary of Contents for Northern Industrial Tools 141456

  • Page 1 1 2 , 0 0 0 L B S . OWNER’S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 141456...

  • Page 2: Intended Use

    For technical questions and replacement parts, please call 1-800-222-5381. Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.

  • Page 3: General Safety Rules

    GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
  • Page 4 Always stand clear of wire rope and load during operation, and keep bystanders away as well. Do not try to guide the cable Always be certain the anchor you select will withstand the load, and the strap or chain will not slip.
  • Page 5 NOTE: In order to gain access to the hardware directly underneath the cable drum it may be necessary to unspool the cable from the winch drum. LUBRICATION All moving parts in the winch are permanently lubricated with high-temperature lithium grease at the time of assembly.
  • Page 6 CAUTION: When attaching wires to the motor or solenoid terminals, hold the inner nut with a wrench while tightening the outer nut with a second wrench. Do not allow the terminals to rotate in their housings. Rotation may cause internal wire damage or part misalignment. For normal self-recovery work, your vehicle’s existing electrical system is adequate.

  • Page 7: Operating Your Winch

    Diagram2: Principle of power works NOTE: 1. Your battery must be kept in good condition. 2. Be sure battery cables are not drawn across any surfaces, which could possibly damage them. 3. Corrosion on electrical connections will reduce performance or may cause a short. 4.
  • Page 8 should be attached to the vehicle frame. 8. Ensure rated “D” or bow shackles are used in conjunction with an approved tree trunk protector to provide a safe anchor point. 9. When extending winch cable, ensure that at least FIVE (5) wraps of cable remain on drum at all times.
  • Page 9 applications. 20. Do not use winch in hoisting applications due to required hoist safety factors and features. 21. Do not use the winch to lift, support or otherwise transport personnel. 22. Never operate your electric winch in a gas station or any place where explosive gasoline fumes are present.
  • Page 10 Radio Control Specifications: Working Voltage 9V–12V Frequency 433MHz Power 10mW Working Temperature to 140 Maximum Control Distance 100 ft. 5. To commence winching operation, start vehicle engine, place transmission in neutral, maintain engine speed at idle. Never winch with your vehicle in gear or in park, which can damage your vehicle’s transmission.

  • Page 11: Maintenance

    USE OF WIRELESS CONTROL The control handle has a 2-in-1 function. It is a wireless control as well as a cable-operating control. Before you use the control in the wireless mode, you must install the battery to make it operational. With the battery installed, the control will work remotely.

  • Page 12: Diagram & Parts List

    DIAGRAM & PARTS LIST Page of 15...
  • Page 13 Item Part No. Description Qty. Item Part No. Description Qty. 7329200.3-2 Washer 7329200.3-1 Gear Box Base 7329200.3-1 SunGear-Input 7329200.3-2 Gear Housing Gear Carrier 7329200.3.1 7329200.3-3 Inner Gear I Ass'y-Input Gear Carrier 7337100.3-1 7329200.3.2 Inner Gear Ⅱ Ass'y-Intermediate 7329200.3-9 Cushion 1.2MM 7329200.3-1 Gasket 9500 Thickness...
  • Page 14 Page of 15...
  • Page 15 Item No. Part No. Description 7329200.60.1-2 Control box cover GB70.2 M5x12 M5x12 Screw GB/T 41 M5 M5 Nut GB70.2 M8X12 Receiver GB/T 862.1 8 M8x12 bolt 732510-24 M8 washer GB/T97.18 A2 8 flat washer (stainless) GB70.2 M6X10 Long red cable with yellow sleeve GB/T862.1 6 Short black cable 7329100.6.1-11...

Table of Contents