Table of Contents
Advertisement
www.braveproducts.com
800-350-8739
WARNING
EXCESSIVE TOWING SPEED CAN CAUSE SERIOUS
INJURIES OR DEATH.
DO NOT EXCEED 45 MI/HR. (73 KM/HR.)
•
BE CERTAIN THAT THE WHEEL LUG NUTS AND AXLE
MOUNTING HARDWARE ARE TIGHTENED.
•
CHECK PRESSURE AND OVERALL CONDITIONS OF
TIRES.
WARNING
IMPROPER OPERATION OF THIS EQUIPMENT CAN
CAUSE SERIOUS INJURY OR DEATH.
READ OPERATOR'S MANUAL SUPPLIED WITH THIS
MACHINE BEFORE OPERATION OR SERVICING.
MODIFICATION OR ALTERATION OF THIS MACHINE
WILL VOID MANUFACTURER'S WARRANTY.
DO NOT ALTER OR MODIFY THIS MACHINE WITHOUT
THE
EXPRESS
WRITTEN
CONSENT
OF
MANUFACTURER.
201154
6. DECAL LOCATION
EMERGENCY STOP
PUSH TO STOP
201026
800-350-8739
WARNING
1. READ AND UNDERSTAND OPERATOR'S MANUAL AND SAFETY SIGNS BEFORE
STARTING.
2. STOP ENGINE, DISCONNECT SPARK PLUG WIRE AND WAIT FOR ALL MOVING
PARTS TO STOP BEFORE SERVICING, MAINATAINING, ADJUSTING OR CLEANING.
3. KEEP HANDS, FEET, HAIR OR CLOTHING AWAY FROM MOVING PARTS.
4. INSTALL, CLOSE AND SECURE ALL GUARDS, SHIELDS AND HOODS BEFORE
OPERATING.
5. DO NOT PLACE HANDS IN THE DRUM UNLESS ENGINE IS OFF AND SPARK
PLUG IS DISCONNECTED OR MOTOR IS OFF AND POWER CORD IS UNPLUGGED.
6. STAY AWAY FROM HOT ENGINE COMPONENTS DURING OPERATION
7. HAVE A LICENCED ELECTRICIAN WIRE UP ELECTRIC MOTORS.
8. DO NOT SMOKE WHEN REFUELING.
9. USE POWER CORD WITH REQUIRED CAPACITY TO CARRY POWER TO ELECTRIC
MOTOR.
10. FOLLOW GOOD SAFETY PROCEDURES WHEN HANDLING FUEL.
11. ROUTE THE POWER CORD OUT OF THE WAY & PROTECT IT FROM DAMAGE.
12. DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE OR A POORLY
VENTILATED AREA WITHOUT ADEQUATE VENTILATION.
13. KEEP WORKING AREAS DRY AND CLEAN TO PREVENT SLIPPING AND
TRIPPING.
14. ALWAYS ATTACH SAFETY CHAIN WHEN TOWING.
15. COMPLY WITH APPLICABLE TRANSPORTING REGULATIONS WHEN TOWING.
16. DO NOT ALLOW RIDERS DURING TRANSPORTING.
17. DO NOT EXCEED A SAFETY TRAVEL SPEED WHEN TRANSPORTATING.
SLOW DOWN FOR CORNERS AND WHEN GOING OVER ROUGH TERRAIN.
201151
WARNING
MISSING GUARD HAZARD
INSTALL, CLOSE AND SECURE ALL GUARDS,
SHIELDS AND HOODS BEFORE OPERATING.
THE
ROTATING PART HAZARD
TO PREVENT SERIOUS INJURY OR DEATH ROTATING PARTS:
1.
INSTALL, CLOSE AND SECURE ALL GUARDS, SHIELDS AND
HOODS BEFORE OPERATING.
2.
DO NOT PLACE HANDS IN DRUM UNLESS THE MOTOR OR
ENGINE IS OFF AND THE POWER CORD UNPLUGGED OR THE
KILL SWITCH ACTIVATED.
3.
KEEP HANDS, FEET, HAIR AND LOOSE CLOTHES AWAY FROM
MOVING PARTS.
201001
201004
WARNING
WARNING
MISSING GUARD HAZARD
INSTALL, CLOSE AND SECURE
ALL GUARDS, SHIELDS AND
HOODS BEFORE OPERATING.
201004
WARNING
KEEP AWAY
MBRPMM106H Rev. A.1
CHECK LIST
CHECK AND TIGHTEN WHEN NECESSARY ALL NUTS AND BOLTS.
CHECK MIXER PADDLE AND WIPERS ADJUSTMENTS AND TIGHTEN
PADDLE BOLTS.
GREASE ALL FITTINGS – GREASE DRUM SEALS TO AVOID DOWN
TIME ON REPAIRS.
CHECK BELT ADJUSTMENT AND TIGHTEN BELT IF NECESSARY.
CHECK TIRE PRESSURE. INFLATE 12" AND 13" TO 30 PSI. 8" TIRES TO
45 PSI. WHEEL LUG TORQUE MUST BE 105 LBF.
ENSURE THE DRUM LOCK AND HOOD FASTENER ARE IN LOCKED
POSITION BEFORE TRANSPORTATION.
WARNING
ROTATING PART HAZARD
KEEP AWAY
TO PREVENT SERIOUS INJURY OR DEATH ROTATING PARTS:
1.
INSTALL, CLOSE AND SECURE ALL GUARDS, SHIELDS
AND HOODS BEFORE OPERATING.
2.
DO NOT PLACE HANDS IN DRUM UNLESS THE
MOTOR OR ENGINE IS OFF AND THE POWER CORD
UNPLUGGED OR THE KILL SWITCH ACTIVATED.
3.
KEEP HANDS, FEET, HAIR AND LOOSE CLOTHES
AWAY FROM MOVING PARTS.
290791
201003
Page 9
Advertisement
Table of Contents
