Toshiba MML-AP0074NH1-E Service Manual page 90

4
PARTS NAME OF REMOTE CONTROLLER
Wireless remote controller and its
functions
1
4
PRESET FAN
13 5
TEMP
MODE
3
2
COMFORT
QUIET SLEEP
16 15
SWING FIX H i -POWER
6
12
11
7
TIMER CLR
ON OFF
14
10
SLEEP SET
CHK FILTER CLOCK
9 8
1
Infrared signal emitter
Transmits a signal to the indoor unit.
2
START/STOP button
Press the button to start operation.
(A receiving beep is heard.)
Press the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor unit,
press the button twice.
3
Mode select button (MODE)
Press this button to select a mode.
Each time you press the button, a mode is selected
in a sequence that goes from A : Auto changeover
control, : Cool, : Dry, : Heat, : Fan only,
and back to A. (A receiving beep is heard.)
4
Temperature button ( )
TEMP
.............. The set temperature is increased up to
TEMP
30°C.
TEMP .............. The set temperature is dropped down to
17°C. (A receiving beep is heard.)
5
Fan speed button (FAN)
Press this button to select fan speed. When you
select AUTO, the fan speed is automatically adjusted
according to the room temperature.
1112750101_(01_EN).indd 9
You can also manually select the desired fan speed
from among fi ve settings.
(LOW , LOW + , MED ,
MED + , HIGH )
(A receiving beep is heard.)
6
Auto louver button (SWING)
Press this button to swing the louver.
(A receiving beep is heard.)
Press the SWING button to stop the louver swinging.
(A receiving beep is heard.)
7
Set louver button (FIX)
Press this button to adjust the airfl ow direction.
(A receiving beep is heard.) While this button is kept
depressed, the receiving tone continuously sounds.
8
Off timer button (OFF)
Press this button to set the OFF timer.
9
On timer button (ON)
Press this button to set the ON timer.
10
Reserve button (SET)
Press this button to reserve time settings.
(A receiving beep is heard.)
11
Cancel button (CLR)
Press this button to cancel ON timer and OFF timer.
(A receiving beep is heard.)
12
High power button (Hi-POWER)
Press this button to start the high power operation.
This function is not operated group control.
13
PRESET button
Press this button to change the operation mode to
the preferred operation mode memorized previously.
To memorize the operation mode, press this button
for at least 3 seconds during the preferred operation
P
mode. is displayed and the operation mode is
memorized.
14
SLEEP button
Press this button to start the OFF timer operation that
automatically adjusts the room temperature and the
fan speed.
You can select the OFF timer time from four
durations (1, 3, 5 or 9 hours).
15
COMFORT SLEEP button
Press this button to start the OFF timer operation that
automatically adjusts the room temperature and the
fan speed.
You can select the OFF timer time from four
durations (1, 3, 5 or 9 hours).
During group control operation, the set temperature
and the fan speed are not automatically adjusted.
Only off timer function is activated.
16
QUIET button
Press this button to start quiet operation.
Pressing this button again will restore normal
operation.
12/15/10 11:25 AM
Names and functions of indications on
wireless remote controller
Display
All indications, except for clock time indication, are
indicated by pressing the START/STOP
8
EN
9
6
• In the illustration, all indications are indicated for
explanation.
During operation, only the relevant indications will be
indicated on the remote controller.
1
Transmission mark
This transmission mark (
remote controller transmits signals to the indoor unit.
2
Mode display
Indicates the current operation mode.
(A : Auto changeover control,
: Heat,
3
Temperature display
Indicates the temperature setting (17°C to 30°C).
When you set the operating mode to
no temperature setting is indicated.
4
FAN speed display
Indicates the selected fan speed. AUTO or one of fi ve
fan speed levels (LOW
MED
can be indicated.
Indicates
Dry.
5
TIMER and clock time display
The time set for timer operation or clock time is
indicated.
The present time is always indicated except for
TIMER operation.
6
Hi-POWER display
Indicates when the high power operation starts.
Press the Hi-POWER button to start and press it
again to stop the operation.
7 P (PRESET) display
Indicated when memorizing the preferred operation
mode or when it has been memorized.
Also, this icon is indicated when the memorized
preferred operation is displayed.
1112750101_(01_EN).indd 10
8
Indicated during the OFF timer operation that
automatically adjusts the room temperature and
the fan speed. Each time you press the COMFORT
SLEEP button, the display changes in the sequence
of 1h, 3h, 5h, and 9h.
button. 9
(QUIET) display
Indicated during the quiet operation.
1 3 2
10
Swing display
10
Indicated during the swinging operation where the
horizontal louver automatically moves up and down.
7
NOTE
5
When both wired remote controller and wireless remote
controller are used, display on the screen of wireless
4
remote controller may differ from the actual operation in
some cases.
Preparation and check before use
1. Loading Batteries
• Remove the battery
8
) indicates when the
cover.
• Insert 2 new batteries
(R03 [AAA]) following
the (+) and (-) positions.
2. Removing Batteries
: Cool, : Dry,
• Remove the battery
: Fan only)
cover.
• Remove the 2 used
batteries.
: Fan only,
Batteries
• To replace the batteries, use two new batteries (R03
[AAA]).
+
, LOW ,
• In normal use, the batteries will last about one year.
, MED + , HIGH )
• Replace the batteries if there is no receiving beep from
the indoor unit or when the air conditioner cannot be
when the operating mode is :
operated using the remote controller.
• To avoid malfunctions by battery leakage, remove the
batteries when not using the remote controller for more
than one month.
• Please dispose of the used batteries according to the
local regulation.
(COMFORT SLEEP) display
2
1
12/15/10 11:25 AM