Subscribe to Our Youtube Channel
Related Manuals for MicroBT WhatsMiner M20S
Summary of Contents for MicroBT WhatsMiner M20S
- Page 1 WhatsMiner M20S Operation Guide V1.0 （Simplified Version) Shenzhen MicroBT Electronics Technology Co.,Ltd 1 / 32...
-
Page 2: Table Of Contents
Catalog 1. M10S Product Introduction......................3 2.Whats Miner Connection and Racking Safety Notes............... 3 2.1.Miner Connection Notes.......................3 2.1.1.Power Supply Control Wire Connection Notes............4 2.1.2.Adapter Board Control Wire Connection Notes............4 2.1.3.Fan Connection Notes....................6 2.1.4.Hash Board and Adapter Board Connection Notes........... 7 2.1.5.Power Supply Copper Busbar Connection Notes............9 2.1.6.Product Connection Check..................10 2.2.Miner Handling and Racking Notes..................10... -
Page 3: M10S Product Introduction
1. M10S Product Introduction Whats Miner M20S Blockchain Server Artifact Product ParameterIntroduction as below： HashRate：68TH/s ±5% Power：3264W±10% Power Rate：48W/T Power Supply：WhatsMiner Power Supply P21（220,3500W±10%） Environment Temperature：-5℃~40℃ Product Size：390mm*155mm*240mm 2.Whats Miner Connection and Racking Safety Notes 2.1.Miner Connection Notes Check over the miner’s power supply control wire and adapter board control wire and fan control wire to make sure connections are correct,the damage of control board、hash board、transfer board、fan, etc. -
Page 4: Power Supply Control Wire Connection Notes
not be covered by the warranty. When connecting the wiring of the control board, the clasp must be corresponding, and the pin cannot be inserted into the socket by force.If the backplug, the power may burn the control board, burning the signal wire! 2.1.1.Power Supply Control Wire Connection Notes The power control wire is 14pin, and the card slot is inserted relative: Correct Connection：... - Page 5 Incorrect Connection： 5 / 32...
-
Page 6: Fan Connection Notes
2.1.3.Fan Connection Notes The fan wire is 6pin, and the card slot is inserted relative: Correct Connection： 6 / 32... -
Page 7: Hash Board And Adapter Board Connection Notes
Incorrect Connection： 2.1.4.Hash Board and Adapter Board Connection Notes The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems! 7 / 32... - Page 8 Correct Connection： Incorrect Connection： 8 / 32...
-
Page 9: Power Supply Copper Busbar Connection Notes
2.1.5.Power Supply Copper Busbar Connection Notes When the power supply copper busbar is connected to the hash board, the positive and negative poles of the copper busbar cannot be connected incorrectly, and the screw washers of the fixed copper bar must be aligned in parallel with the edge of the copper bar. -
Page 10: Product Connection Check
2.1.6.Product Connection Check After all the connections of the miner are connected and all the screws are tightened, check again to confirm that the connection is correct. 2.2.Miner Handling and Racking Notes In the process of handling and racking of the miner, it is strictly forbidden to use the data cable, the power supply control wire and the fan wire as the load-bearing handle of the miner, and to pick up the machine and the power supply. -
Page 11: Miner Configuration Environment Preparation
3. Miner Configuration Environment Preparation 3.1.Miner Configuration Equipment List Tool Numb Remark Computer Miner configuration Miner Power Power the miner Supply Configuring miner and The switch can Switch configuration computer connect to the network communication Internet. 1、Provide a dynamic IP It defaults to DHCP address for the initial DHCP/NTP... -
Page 12: Miner Network Environment
3.2.Miner Network Environment The miner defaults to DHCP to obtain dynamic ip. Therefore, the mine network must be configured with a DHCP server, or the router can enable dhcp to dynamically allocate the IP address service.The running time of the miner, the correctness of the calculation statistics, etc. -
Page 13: Miner Data Configuration（Configuration On The Web
washers of the fixed copper bar must be aligned parallel to the edge of the copper bar, and the fixed screws must be tightened, otherwise the power board may be burned out. , control board or power supply, hardware damage caused by copper stripping, is not covered by the warranty. -
Page 14: Check The Ip Address Reported By The Miner
5.1.2.Check the IP address Reported by the Miner （1）After the machine is powered on for about 30s, under normal circumstances, the yellow light of the network port is always on and the green light is blinking. Press the IPFOUND function button (long button highlighted) on the miner control panel for more than 5s, the two LEDs on the right will flash a few times, indicating that the machine has broadcast the IP and MAC address of the unit to the network. -
Page 15: Configuration Pool&Worker Data And Ntp Server Address
whether the switch is normal, the network cable connection is reliable, and the quality of the network cable is faulty. （3）The computer and miner running the WhatsMinerTools software must be on the same network segment. Otherwise, the software may not receive the broadcast message from the machine, so that the ip address and mac address information reported by the machine ipfound button cannot be queried. - Page 16 After the configuration of the mining pool is modified, the modified configuration must be restarted after the cgminer program is restarted or the control panel is restarted. （3）Restart cgminer to check whether the configuration modification takes effect. In the miner interface, select: Status-"CGMinerStatus" to enter the CGMiner running status interface.
- Page 17 （4）Restart the control board and check whether the configuration modification takes effect. (If you do not choose to restart cgminer, after the configuration is modified and saved, you can also restart the control board to make the configuration take effect.) In the system interface,click on”Reboot”.
-
Page 18: Modify The Ntp Synchronization Server Address (Optional)
5.2.2.Modify the NTP Synchronization Server Address (optional) （1）After logging in, select System->>System Configuration in the interface to enter the Cgminer configuration page. （2）In the cgminer configuration interface, add or modify the NTP server address. The miner has been configured with four NTP server addresses by default. You can modify or add the NTP server address to the local NTP server address according to the mine situation. - Page 19 In the "Configuration" interface, click "Edit". （3） In the interface modification page, select "Static address" for the protocol and click （4） "Switch protocol". 19 / 32...
-
Page 20: Miner Operation Status Check
（5）In the static address configuration interface, change the IP address, mask, gateway, broadcast address, and DNS address to the actual planned address of the mine. After editing, click "Save & Apply" in the lower right corner. After saving the application, you need to re-use the newly set static IP address to log in to the mining machine (otherwise the page will display loading until the loading fails). - Page 21 Notes: （1）The mining machine is connected correctly. When the network is normal, the mining machine will automatically perform the frequency search test after power-on. The search frequency test phase takes about 15 minutes. After the search frequency is over, it will enter the formal mining stage.
-
Page 22: Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade
7.Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade You can use the WhatsMinerTool software to carry out batch data configuration, status check and firmware upgrade of the mining machine. For details, please refer to the "Whats Miner WhatsMinerTool Operation Guide". 8.Miner Disassembly and Installation 8.1. - Page 23 2）Unplug the power control cable and the adapter board control cable connected to the control panel as shown： 3）Remove the four screws fixed on the bracket and take out the control panel from the bracket as shown： 23 / 32...
-
Page 24: Control Panel Installation
8.1.2.Control Panel Installation 1）When installing the control board, first fix the 4 screws on the control board bracket, as shown in the figure： 2）Insert the power control cable and the adapter board control cable into the corresponding slots on the control board, and then fix the bracket to the chassis with screws, as shown in the figure：... -
Page 25: Power Supply Disassembly And Installation
8.2.Power Supply Disassembly and Installation 8.2.1.Power Supply Disassembly 1）Remove the four screws that secure the power supply on the chassis , and then remove the six screws that secure the copper bars on the power supply. Unplug the fan cable on the power supply . 2）After the above operation is completed, gently pull out the power supply (do not pull out too long, the power control cable is still connected to the control panel), as shown in the figure：... -
Page 26: Power Supply Installation
3）Unplug the power control cable on the control panel, remove the power supply, and remove the power supply： 8.2.2.Power Supply Installation 1）First plug the control cable of the power supply into the corresponding slot on the control panel, as shown below： 2）Then connect the 6 positive and negative terminals on the power supply to the copper row one by one, and then install 6 screws in turn. -
Page 27: Hash Board Disassembly And Installation
3）Finally, tighten the screws of the four fixed power supplies on the chassis, and the power supply is installed, as shown below： 8.3.Hash Board Disassembly and Installation 8.3.1.Hash Board Disassembly 1）There are three hash boards on each mining machine (the order number of the hash board is as shown below). - Page 28 2）Remove the adapter plate and the copper bar fixed to the control panel as shown： 3）Extract the faulty hash board outward, as shown： 28 / 32...
- Page 29 4）After taking out the hash board, record the serial number above or use WeChat “sweep” to scan the power board serial number and provide it to the relevant after- sales technician, as shown： 29 / 32...
-
Page 30: Hash Board Installation
8.3.2.Hash Board Installation 1）When the hash board is loaded into the chassis, one hand holds the board into the hash board slot, and sequentially enters the chassis, as shown in the figure： 2）After installing the hash board into the chassis, first install the adapter board. The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems, as shown：... - Page 31 After the adapter plate is installed, install the copper bar. When the power busbar is 3） connected to the hash board, the positive and negative poles of the copper bar cannot be connected incorrectly, and the screw pads of the fixed copper bar must be aligned with the edge of the copper bar, otherwise it may be possible to power on.
- Page 32 4）After the copper row is installed, the control board and the fan are installed, and the hash board is installed, as shown： 32 / 32...
Need help?
Do you have a question about the WhatsMiner M20S and is the answer not in the manual?
Questions and answers