Fujitsu AIRSTAGE AJY072LALBH Installation Manual page 20

Setting number (xx00)
Setting number (xx01)
Electricity meter
······
pulse setting 1 *3
72
Setting number (xx98)
Setting number (xx99)
Set the ones digit and tens digit of the No. of the electricity meter pulse setting
connected to CN135.
Setting number (00xx)
Setting number (01xx)
Electricity meter
······
pulse setting 2 *3
73
Setting number (98xx)
Setting number (99xx)
Set the hundreds digit and thousands digit of the electricity meter pulse setting
connected to CN135.
*1: Do not set this for outdoor units with Slave setting.
*2: When electricity meter No. is set to "000" and "201 to 299", the pulses input to CN135
become ineffective. Available setting number is "001" to "200"
*3: When the electricity meter pulse setting is set to "0000", the pulses input to CN135
become ineffective. Available setting number is "0001" to "9999"
(1) Turn on the power of the outdoor unit and enter standby mode.
• When system is normal
POWER/MODE lamp lights up. (ERROR lamp is off.)
POWER/MODE lamp:
ON
7 segment LED indicator:
OFF
MODE/EXIT button
• When system is abnormal
Check the settings as there is an error in the settings for outdoor unit address (DIP switch
SET3-1, 2) or number of connected slave units (DIP switch SET3-3, 4).
POWER/MODE lamp:
ON
7 segment LED indicator:
"-" display
(2) Setting method
Use the "MODE/EXIT", "SELECT", and "ENTER" buttons to confi gure settings accord-
ing to the procedures below.
(If no setting is made, the factory default setting will be displayed.)
MODE/EXIT : Press the "MODE/EXIT" button.
: Press the "SELECT" button.
SELECT
: Press the "ENTER" button.
ENTER
ENTER : Press the "ENTER" button for more than 3 seconds.
En-19
0 0
0 1
7 2 ··· ···
9 8
9 9
0 0
0 1
7 3 ··· ···
9 8
9 9
ERROR lamp: OFF
POWER
ERROR
MODE
LED101 LED102
(GREEN) (RED)
LED105 LED104
MODE
SELECT ENTER
/EXIT
SW107 SW108 SW109
ENTER button
SELECT button
ERROR lamp:
Blinking
POWER
ERROR
MODE
LED101 LED102
(GREEN) (RED)
LED105 LED104
MODE
SELECT ENTER
/EXIT
SW107 SW108 SW109

1: FUNCTION Setting
First 2 digits
Last 2 digits
MODE/EXIT

SELECT
ENTER
2: Setting the
fi rst 2 digits
SELECT
Every press of the
"SELECT" button will
change the setting
number for the fi rst 2
digits.
SELECT
MODE/EXIT
EXIT: Press the "MODE/EXIT" button to cancel the setting mode.
7 segment LED indicator
(LED105, LED104)
(Flashing)
(When [F3] to [F9] are displayed, continue to press
the "SELECT" button until [F2] is displayed.)
3: Setting the last 2 digits
Continue to press the "SELECT" button
until the desired number appears at the
last 2 digits.
ENTER
MODE/EXIT
SELECT
SELECT
SELECT
SELECT
ENTER
Setting is complete when the lamp lights up
Press "ENTER" button to return to "2. Setting
the first 2 digits" (If there is no operation for
5 seconds after the setting, the indicator will
return to "2: Setting the first 2 digits".)
ENTER
MODE/EXIT
SELECT
(Continue to press the
"SELECT" button until the
desired number appears at
the last 2 digits.)
ENTER
Setting is complete when the lamp lights up
Press "ENTER" button to return to "2. Setting the
fi rst 2 digits" (If there is no operation for 5 seconds
after the setting, the indicator will return to
"2: Setting the fi rst 2 digits".)
SELECT
SELECT