Table of Contents
Advertisement
Quick Links
Always Moving Forward
Operating Manual
Please Read Before Operating Unit
Model WC601B Rotary Tubing Cutter
Service and All Spare Parts Available
The Eraser Company, Inc.
Eraser International Ltd.
PO Box 4961/ Oliva Drive
Unit M, Hunting Gate
Syracuse, NY 13221, USA
Andover SP10 3SJ, England
Phone: (315) 454-3237 / Fax: (315) 454-3090
Phone: (01264) 351347 / Fax: (01264) 355030
Website: www.eraser.com
Website: www.eraser-international.com
E-mail: info@eraser.com
Email: sales@eraser-international.com
Advertisement
Table of Contents
Related Manuals for Eraser WC601B
Summary of Contents for Eraser WC601B
- Page 1 Always Moving Forward Operating Manual Please Read Before Operating Unit Model WC601B Rotary Tubing Cutter Service and All Spare Parts Available The Eraser Company, Inc. Eraser International Ltd. PO Box 4961/ Oliva Drive Unit M, Hunting Gate Syracuse, NY 13221, USA...
-
Page 2: Ordering Information
Weight.............26 lbs. (11.8 Kg) (1011mm/sec) 2200 1950 1900 1650 Eraser Company Inc. • Syracuse, NY USA • Ph: 315-454-3237 • info@eraser.com • www.eraser.com • Fax 315-454-3090 Eraser International Ltd. • England • Ph:(01264)351347 • sales@eraser-international.com • www.eraser-international.com • Fax (01264)355030... -
Page 3: Operation
WC601B CUTTER HEAD AND FEED BELTS 4 LINE KEYPAD DISPLAY Eraser Company Inc. • Syracuse, NY USA • Ph: 315-454-3237 • info@eraser.com • www.eraser.com • Fax 315-454-3090 Eraser International Ltd. • England • Ph:(01264)351347 • sales@eraser-international.com • www.eraser-international.com • Fax (01264)355030... - Page 4 Model WC601B Bushing Installation Drawing 1. Install the entrance bushing chamfer side out (to the left). Make certain it does not interfere with the feed belts when they are fully closed. Tighten the set screw to lock its position. 2. Insert chamfered side of head bushing toward belt feed. Position it so that the end opposite the chamfer is as close as possible to the blade without interference when cutter head is engaged.
-
Page 5: Grounding Instructions
NOT safety or altered by anyone other than Eraser, or which has glasses. Also use face or dust mask if cutting operation is been used in a manner or for a purpose for which the dusty. -
Page 6: Bushing Installation
Place the material to be cut on the dereeler. Turn the reached. WC601B on using the I/O switch on the back side of the unit. To open the front cover, lift the hinged cover that is magneti- Press ENTER to select the default, or type in a new number. -
Page 7: Creating A New Batch
Cut Time 1.000 (Enter 0.1 to any number of seconds, 1 is default) tension, actual cut length may vary from the inputted length by a proportional amount. The WC601B incorporates a length The cut speed controls the speed and pressure at which the compensation feature to provide an easy adjustment in these rotary blade cuts through the material. - Page 8 4, 5 and 6 (not necessarily in that order). The Select batch#6 WC601B will then feed and cut a 6” piece, 3 8” pieces and a Kit 1 Index 3 2” piece. The quantity of kits (i.e. the number of sets of Enter # to change lengths) is entered when defining a kit.
-
Page 9: Maintenance
POWER FAILURE: Adjust the blade as described in the blade change or In case of a power failure, the WC601B will be reinitialized and replacement section: Head or exit bushings may be adjusted will not start unexpectedly. All parameters stored in a batch too close to the blade. - Page 10 Memory Organization of Batches and Kits Batches are any number of pieces cut to 1 length. In memory, the WC601B uses 5 variables in an array: the length, the unit of measure, the compensation factor, the quantity of pieces to cut, and the feed rate.
Need help?
Do you have a question about the WC601B and is the answer not in the manual?
Questions and answers