Table of Contents
Advertisement
Quick Links
English
Français
Español
WARNING
READ YOUR INSTRUCTIONS COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP YOUR
NEW SNOWTHROWER SHIELD OR OPERATE YOUR SNOWTHROWER WITH YOUR SHIELD INSTALLED.
Questions, problems, missing parts? Before returning to your retailer, call Classic Accessories customer service at
1-800-854-2315, 8 a.m. - 4 p.m., PST, Monday-Friday. Email: customerservice@classicaccessories.com
(page 01)
(page 15)
(página 29)
ITEM/ARTICLE/ARTÍCULO: 52-065-010404-00
SNOW THROWER SHIELD
12cH56_12797
Advertisement
Table of Contents
Related Manuals for Classic Accessories 52-065-010404-00
Summary of Contents for Classic Accessories 52-065-010404-00
- Page 1 READ YOUR INSTRUCTIONS COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP YOUR NEW SNOWTHROWER SHIELD OR OPERATE YOUR SNOWTHROWER WITH YOUR SHIELD INSTALLED. Questions, problems, missing parts? Before returning to your retailer, call Classic Accessories customer service at 1-800-854-2315, 8 a.m. - 4 p.m., PST, Monday-Friday. Email: customerservice@classicaccessories.com...
-
Page 2: Safety Information
If attachment while it is moving. Keep safety devices in you have any questions regarding the product please call place and in working condition. Classic Accessories customer service at 1-800-854-2315, • Keep hardware tight. 8 a.m. - 4 p.m., PST, Monday-Friday. • Keep hands, feet, clothing, jewelry, and long hair away from any moving parts, to prevent them from getting 1. -
Page 3: Tools Needed
PACKAge CONteNts LIst (PARts) START ASSEMBLY ON PAGE 4 Part Description Quantity Part Description Quantity Left Base Bar Short Hoop Support Pole Right Base Bar Short Hoop Support Pole Mounting Post Lower, Left Small Loop Clamp Mounting Post Lower, Right Hex Bolt - short Mounting Post Center Large Loop Clamp Mounting Bar Top, Left... - Page 4 STEP 1 ASSEMBLE THE FRAME (FIG. 1-9) Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting. PARTS NEEDED TOOLS NEEDED NONE Inside view Slide mounting posts [A, B] together until spring button pops through hole. Insert mounting post lower left [C] onto the end of left base Insert mounting post lower right [D] onto the end of right bar [A] until spring button pops through hole.
- Page 5 STEP 1 continued... ASSEMBLE THE FRAME (FIG. 1-9) Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting. PARTS NEEDED TOOLS NEEDED NONE Insert both mounting post upper [E] onto upright studs on lower mounting [C, D] until spring button pops through hole.
- Page 6 STEP 1 continued... ASSEMBLE THE FRAME (FIG. 1-9) Note: Assemble frame on a clean flat surface next to your snow thrower for easy mounting. PARTS NEEDED TOOLS NEEDED NONE Slide top mounting bars [F, G] together until spring button pops through hole. Attach top mounting bar assembly [F, G] to the top of mounting posts Make sure the stub tubes on [F, G] are facing the same [E] until spring button pops through holes.
- Page 7 STEP 2 ASSEMBLE THE FRONT SHIELD (FIG. 1-4) WARNING: Use care when assembling the poles. Poles under tension can slip out of the metal/plastic sleeves causing serious injury. safety goggles are recommended. PARTS NEEDED TOOLS NEEDED NONE Insert one long hoop pole [I] into [J] to assemble the lower support rod. Lay out the shield shell [H].
- Page 8 STEP 3 INSTALL THE FABRIC SHIELD SHELL ONTO THE METAL FRAME (FIG. 1-6) Note: Fabric shell will be tight when properly assembled. PARTS NEEDED TOOLS NEEDED NONE Insert one end of the longer flexible [I,J] support rod into Firmly insert the support pole completely into the stub tube. the lower stub tube connecting [C] to [D].
- Page 9 STEP 3 continued... INSTALL THE FABRIC SHIELD SHELL ONTO THE METAL FRAME (FIG. 1-6) Note: Fabric shell will be tight when properly assembled. PARTS NEEDED TOOLS NEEDED NONE NONE Tighten up the skin by closing around the support bars all of the rip-n-grip strips on both sides and at the bottom of the frame.
- Page 10 STEP 4 ATTACH THE MOUNTING SYSTEM TO YOUR SNOW THROWER SHIELD (FIG. 1-3) Note: Exact positioning may vary depending on your machine. PARTS NEEDED TOOLS NEEDED 1/2 in. Box Wrench Adjustable Wrench 1/2 in. Socket Wrench Slide on the small loop clamp [M] onto the two open spaces on the lower part of the shield frame [A,B].
-
Page 11: Parts Needed
STEP 5 ATTACH THE MOUNTING SYSTEM TO YOUR SNOW THROWER FRAME (FIG. 1-2) Note: Exact positioning may vary depending on your machine. Note: In some instances, it may be necessary to mount the loop clamps [L] or [M] above the handlebar crossbar support. This will help the assembled shield sit higher for added protection. - Page 12 STEP 6 - for lighter weight machines ATTACH THE COUNTER BALANCE BAG TO YOUR SNOW THROWER (FIG. 1-5) Note: Exact positioning may vary depending on your machine. Exact weight may vary depending on your machine. PARTS NEEDED TOOLS NEEDED NONE Weight Not Included Fill the counter balance bag Roll the top of the counter balance...
- Page 13 STEP 7 MOUNTING THE FRAME (FIG. 1-4) PARTS NEEDED TOOLS NEEDED 1/2 in. Box Wrench Adjustable Wrench 1/2 in. Socket Wrench Lift your pre-assembled shield and align the two loop clamps. Insert Hex bolt [Q] through both loop clamps [M] & [O]. Repeat on the other side.
-
Page 14: Troubleshooting
ONE YEAR LIMITED WARRANTY The manufacturer, Classic Accessories, Inc., will repair or replace, without charge, this product which under normal usage has proven to be defective in its manufacture or workmanship for a period of one (1) year from the date of initial retail purchase. This warranty is valid only to the original purchaser.
Need help?
Do you have a question about the 52-065-010404-00 and is the answer not in the manual?
Questions and answers