Technical Data; Operation - Everwin SN40 Series Operation And Maintenance Manual

SN40PA
MODEL SN40P-R
SN402PLM
3/4"~1-9/16"
(19 - 40 mm)
LENGTH
(25 - 50 mm) for
SN402P,
SN402PLM
CROWN
(26.4 mm)
THICKNESS
(1.4 mm)
WIDTH
(1.6 mm)
GAUGE
TOOL AIR FITTING
This tool uses a 1/4-18 N.P.T or 1/4-19 P.T. male plug. The inside diameter should be .200" (5 mm) or larger. The
fitting must be capable of discharging tool air pressure when disconnected from the air supply.
AIR CONSUMPTION
Tool air consumption: SN50-1.9 cfm (0.9 liter/sec), SN40-1.7 cfm (0.8 liter/sec) of free air to operate at the rate of
100 nails per minute, at 90 PSI (6.0 kg/cm 2 ). Take the actual rate at which the tool will be run to determine the amount
of air required. For instance, if your fastener usage averages 50 nails per minute, you need 50% of the tool air
consumption in running at 100 nails per minute.
NOISE
A-weighted single-event sound power level LWA,1s: SN50-107.4, SN40-105 dBA
A-weighted single-event emission sound pressure level at work station LpA 1s,d: SN50 -106.9, SN40 -104.7 dBA
These values are determined and documented in accordance to EN12549.
VIBRATION
Vibration characteristic value: SN50-3.46, SN40-5.13 m/s
These values are determined and documented in accordance to ISO 8662-11.
This value is a tool-related characteristic value and does not represent the influence to the hand-arm-system when
using the tool. An influence to the hand-arm-system when using the tool will, for example, depend on the gripping
force, the contact pressure force, the working direction, the adjustment of mains supply and the workpiece support.
Refer to Operation Instructions and warnings on pages before proceeding to use this tool.
CONTACT TRIP: IDENTIFIED BY BLACK TRIGGER
SN40P SN40S2
SN40S2A
SN40S2-R
SN402P SN402S2
SN402S2LM
3/4"~1-9/16"
(19 - 40 mm)
1"~2" 1"~2"
(25 - 50 mm) for
SN402S2,
SN402S2LM
1-1/16" 1"
(25.4 mm)
.055" .055"
(1.4 mm)
.062" .062"
(1.6 mm)
16

TECHNICAL DATA

OPERATION

FOUR TYPES OF OPERATION FOR THIS TOOL SERIES.
SN40GSW
SN40GSWA
SN40GSW-R
SN50GS-14A
SN402GSW
SN402GSWLM
3/4"~1-9/16"
(19 - 40 mm)
1"~2"
(25 - 50 mm) for
SN402GSW,
SN402GSWLM
15/16"
(23.8 mm)
.055"
(1.4 mm)
.062"
(1.6 mm)
2
7
SN50GS-14
SN40GSW-14
1"~2" 3/4"~1-9/16"
(25 - 50 mm) (19 - 40 mm)
1/2"
(13.7 mm) (24.7 mm)
.071" .071"
(1.8 mm) (1.8 mm)
.083" .083"
(2.1 mm) (2.1 mm)
14
1"