Everwin SN41 Series Operation And Maintenance Manual
Hide thumbs
Also See for SN41 Series:
- Operation and maintenance manual (20 pages) ,
- Operation and maintenance manual (17 pages)
Table of Contents
Advertisement
Quick Links
SN41 Series
Pneumatic Stapler
OPERATIONS and MAINTENANCE MANUAL
CE DECLARATION OF CONFORMITY
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND STUDY
THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND
INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE
REFERENCE.
Everwin Pneumatic Corp.
19'/3/19
Advertisement
Table of Contents
Related Manuals for Everwin SN41 Series
Summary of Contents for Everwin SN41 Series
- Page 1 SN41 Series Pneumatic Stapler OPERATIONS and MAINTENANCE MANUAL CE DECLARATION OF CONFORMITY BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.
-
Page 2: Table Of Contents
NOTE: Additional safety measures may be required because of your particular application of the tool. Contact your EVERWIN representative or distributor with any questions concerning the tool and its use. Everwin Pneumatic Corp., Taichung City, Taiwan 41353. -
Page 3: 1-Year Limited Warranty
(as a gauge for the tool’s age) and photos/videos of the defect for test and evaluation to find root causes. EVERWIN’s analyst will judge the issuance of defective parts and will replace at no charge if evaluation results show that the root cause is defect in material and/or workmanship. -
Page 4: Ce Declaration Of Conformity
Europäischen Richtlinien 2006/42/EC und den Europäischen Norm EN 792-13. CE Déclaration de conformité FRANCAIS EVERWIN PNEUMATIC CORP. déclare et prend sur soi toute la responsabilité de cette déclaration, que le produit est en conformité avec les Directives Européennes 2006/42/EC et avec la norme harmonisée EN 792-13. CE konformiteitsverklaring NEDERLANDS EVERWIN PNEUMATIC CORP. -
Page 5: Safety Instructions
SAFETY INSTRUCTIONS TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR SERIOUS INJURY. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. -
Page 6: Specifications
SPECIFICATIONS TOOL SPECIFICATIONS SN41S4 SN41S2 SN412S2 SN41S2-R MODEL SN41S5 SN41P SN412P SN41P-R SN41GSI SN41GSW SN412GSW SN41GSW-R HEIGHT 8.8" (225 mm) 8.8" (225 mm) 8.8" (225 mm) 8.8" (225 mm) WIDTH 2.5" (64 mm) 2.6" (67 mm) 2.5" (64 mm) 2.6" (67 mm) LENGTH 13.9"... -
Page 7: Technical Data
OPERATING PRESSURE 70 to 120 PSI (5 to 8 kg/cm ). Select the operating pressure within this range for best fastener performance. DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE. TECHNICAL DATA AIR CONSUMPTION Tool air consumption: 1.27 cfm (0.6 liter/sec) of free air to operate at the rate of 60 nails per minute, at 80 PSI (5.6 kg/cm 2 ). -
Page 8: Directional Exhaust
The Trigger Operated model is cycle by actuation of the trigger only. The model does not have a Contact Arm and is intended for use only where a Contact Arm CANNOT be used to satisfy the requirements of the application. The Trigger Operated tool will cycle each time the trigger is actuated. -
Page 9: Lubrication
LUBRICATION Frequent, but not excessive, lubrication is required for best performance. A i r - t o o l oil added through the air line connection will lubricate the internal parts. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance. -
Page 10: Depth Of Drive Adjustment
LOADING THE TOOL: Move pusher backward: Pull pusher to rear until latched. Cover will open. Pusher front will drop into notch on the top of magazine assembly. Loading Fasteners: Drop staple stick over magazine and slide forward. Repeat until magazine is loaded, allow enough space for pusher to disengage the magazine and cover to close. -
Page 11: Tool Operation
TOOL OPERATION EYE PROTECTION which conforms to ANSI/ CE specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury. -
Page 12: Tool Operation Check
4. REMOTE FIRE: The Remote fire model is cycle by actuation of remote valve (RCVA1) for mounted machine. TOOL OPERATION CHECK CAUTION: Remove all fasteners from tool before performing tool operation check. 1. CONTACT TRIP OPERATION: a. With finger off the trigger, press the contact trip against the work surface. THE TOOL MUST NOT CYCLE. -
Page 13: Maintaining The Pneumatic Tool
⚫ Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area. ⚫ Do not use the tool as a hammer. ⚫ Always carry the tool by the handle. Never carry the tool by the air hose. ⚫... -
Page 14: Troubleshooting / Repairs
TROUBLESHOOTING / REPAIRS The troubleshooting and / or repairs shall be carried out only by the authorized dealer / distributor or by other pneumatic tool specialists. QUICK JAM-RELEASING MAGAZINE The stapler contains a “Quick Jam-Releasing Magazine” feature. The magazine is spring loaded to reduce jamming.
Need help?
Do you have a question about the SN41 Series and is the answer not in the manual?
Questions and answers