1. Manuals
  2. Brands
  3. Everwin Manuals
  4. Tools
  5. SN41 Series
  6. Operation and maintenance manual

Everwin SN41 Series Operation And Maintenance Manual

Hide thumbs Also See for SN41 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
TOUGHER FASTER SMARTER
Pneumatic Stapler
SN41 Series
OPERATIONS and MAINTENANCE MANUAL
!
WARNING:
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND
STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY
WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE
REV September, 23, 2022
TOOL FOR FUTURE REFERENCE.
104630

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SN41 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Everwin SN41 Series

Summary of Contents for Everwin SN41 Series

  • Page 1 TOUGHER FASTER SMARTER Pneumatic Stapler SN41 Series OPERATIONS and MAINTENANCE MANUAL WARNING: BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD READ AND STUDY THIS MANUAL TO UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE REV September, 23, 2022 TOOL FOR FUTURE REFERENCE.

  • Page 2: Table Of Contents

    NOTE Additional safety measures may be required because of your particular application of the tool. Contact your EVERWIN representative or distributor with any questions concerning the tool and its use.

  • Page 3: 1-Year Limited Warranty

    (as a gauge for the tool’s age), and photos/videos of the defect for test and evaluation to find root causes. EVERWIN’s analyst will judge the issuance of defective parts and will.

  • Page 4: Ce Declaration Of Conformity

    EVERWIN PNEUMATIC CORP. förklarar härmed att produkten överensstämmer med följande normer och direktiv 2006/42/EC och SS-EN ISO 11148-13:2018. SAMSVARSERKLÆRING / CE Deklaration NORSK EVERWIN PNEUMATIC CORP. erklærer herved att produktet er i samsvar med følgende normer og direktiv 2006/42 EC og NS- EN ISO 11148-13:2018. Todistus CE standardinmukaisuudesta FINSK EVERWIN PNEUMATIC CORP.

  • Page 5: Safety Instructions

    SAFETY INSTRUCTIONS TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE Before operating this tool, all operators should read and study this manual to understand and follow the safety warnings and instructions. Failure to follow warnings could result in death or serious injury. Keep these instructions with the tool for future reference.
  • Page 6 SAFETY INSTRUCTIONS FASTENER LOADING When loading the tool: 1.) Never place a hand or any part of body in the fastener discharge area of the tool; 2.) Never point the tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, causing injury.

  • Page 7: General Safety Instruction

    EVERWIN fasteners driving tools consist of: tool and fasteners. In the ．Keep bystanders away (when working in an area where there is a interests of operator and system safety, the tool and fasteners referred to likelihood of through traffic of people).
  • Page 8 EVERWIN PNEUMATIC CORP. ．Wear warm clothing when working in cold conditions, keep your hands ．Use only lubricants recommended by EVERWIN PNEUMATIC CORP. warm and dry. slippery surfaces caused by use of the tool and also trip hazards caused ．If you experience numbness, tingling, pain, or whitening of the skin in...

  • Page 9: Specifications And Technical Data

    SPECIFICATIONS AND TECHNICAL DATA SPECIFICATIONS SN41S4 SN41S5 SN41S5-D SN412S2 SN41S2 Model SN41S2-R SN41S4A SN41S5A SN41S5A-D SN412S2A SN41S2A 255mm 255mm 256.5mm 255mm 255mm 255mm Height (8.8") (8.8") (8.8") (8.8") (8.8") (8.8") 64mm 64mm 64mm 64mm 67mm 67mm Width (2.5") (2.5") (2.6") (2.5") (2.6") (2.6")
  • Page 10 SPECIFICATIONS AND TECHNICAL DATA TOOL AIR FITTING This tool uses a 1/4"-19 P.T & 1/4"-18 N.P.T male plug. The inside diameter should be 5 mm (0.200") or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply. OPERATING PRESSURE 5 to 8bar (70 to 120PSI ).

  • Page 11: Operation : Trigger Selection

    OPERATION : TRIGGER SELECTION Refer to Operation Instructions and warnings pages before proceeding to use this tool. There are four available systems in these tools : 1. Contact Trip 2. Sequential Trip 3. Automatic Operated 4. Remote Fire Identified by Control Valve Identified by Blue Valve Identified by Black Trigger Identified by Grey Trigger...

  • Page 12: Operation : Air Supply And Connections

    OPERATION : AIR SUPPLY AND CONNECTIONS DO NOT USE OXYGEN, COMBUSTIBLE GASES, OR BOTTLED GASES AS A POWER SOURCE FOR THIS TOOL AS TOOL MAY EXPLODE, POSSIBLY CAUSING INJURY. FITTINGS Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source.

  • Page 13: Operation : Lubrication

    OPERATION : LUBRICATION Frequent, but not excessive, lubrication is required for best performance. Air - tool oil added through the air line connection will lubricate the internal parts. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool, resulting in poor tool performance and frequent tool maintenance.

  • Page 14: Operation : Fastener Loading

    OPERATION : FASTENER LOADING EYE PROTECTION Which conforms to ANSI/ CE specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating, or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

  • Page 15: Operation : Tool Operation System

    OPERATION : TOOL OPERATION SYSTEM EYE PROTECTION Which conforms to ANSI/ CE specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating, or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

  • Page 16: Operation : Tool Operation Check

    OPERATION : TOOL OPERATION CHECK CAUTION Remove all fasteners from tool before performing tool operation check. 1. Contact Trip Operation / 2. Sequential Trip Operation Automatic Operation a. Press the contact trip against the work surface, without a. With finger off the trigger, press the contact trip against touching the trigger.

  • Page 17: Operation : Tool-Specific Features

    OPERATION : TOOL-SPECIFIC FEATURES WARNING ALWAYS disconnect air supply before performing following adjustment. Depth of Drive Adjustment The “DEPTH OF DRIVE ADJUSTMENT” feature provides close control of the fastener drive depth; from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in the specific work as described above, then use the “DEPTH OF DRIVE ADJUSTMENT”...

  • Page 18: Maintaining The Pneumatic Tool

    MAINTAINING THE PNEUMATIC TOOL 1. For increasing driving speed Rotate valve counterclockwise to increase speed Speed Adjustment Valve 2. For reducing driving speed (Automatic Ver. Only) Rotate valve clockwise to reduce speed MAINTAINING THE PNEUMATIC TOOL WARNING When working on pneumatic tools, note the warnings in this manual and use extra care evaluating tools with problems. Disconnect the air supply and empty the magazine when inspecting or maintaining the tool.

  • Page 19: Trouble Shooting / Repairs

    TROUBLESHOOTING / REPAIRS The troubleshooting and / or repairs shall be carried out only by the authorized dealer / distributor or by other pneumatic tool specialists. Quick Jam-Releasing Magazine The stapler contains a “Quick Jam-Releasing Magazine” feature. The magazine is spring loaded to reduce jamming. When a jam does occur, a quick release mechanism at the rear of the magazine allows the magazine to move back, in order to clear the jam.

This manual is also suitable for:

Sn41s4Sn41s5Sn41s5-dSn412s2Sn41s2Sn41s2-r ... Show all

Table of Contents