Advertisement
Quick Links
2-Shelf Tower with Doors • ONHD3033 • INSTRUCTIONS
Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and rubber mallet.
ST-E
DR-E
Parts :
ST-A: Back Panel
(30.25" x 28" x 1")
Quantity: 1
ST-E: Left Side
ST-F: Right Side
(15" x 31" x 1")
(15" x 31" x 1")
Quantity: 1
Quantity: 1
IMPORTANT NOTICE:
Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.
Check to be sure that you have all parts and hardware.
Remove all wrapping materials, including staples & packing straps before you start to assemble.
Do not tighten all screws/bolts until completely assembled.
Keep all hardware parts out of reach of children.
CARTONS: ST3330, STD3033
ST-G
ST-C
ST-D
ST-B: Shelves
(28" x 13" x 1")
Quantity: 2
ST-G: Top
(29.5" x 15" x 1")
Quantity: 1
ST-H: Base
(28" x 14.25" x 1")
Quantity: 1
Any problems or questions call Regency Office Furniture at 1-866-816-9822
ST-F
DR-F
ST-H
ST-C: Center Support
Quantity: 1
2-Shelf Tower with Doors
Figure 1:
Cam Lock Assembly:
To open Cam, point arrow
toward Cam Pin hole. To lock
Cam, turn clockwise.
ST-D: Foot Bracket
(15"D)
Quantity: 2
DR-E: Left Door
DR-F: Right Door
(14" x 30" x 1")
(14" x 30" x 1")
Quantity: 1
Quantity: 1
Page 1
Advertisement
Related Manuals for Regency ONHD3033
Summary of Contents for Regency ONHD3033
- Page 1 Remove all wrapping materials, including staples & packing straps before you start to assemble. Do not tighten all screws/bolts until completely assembled. Keep all hardware parts out of reach of children. Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 2 Then, connect the Base(ST-H) to Back Panel(A) by inserting and Right Side(ST-F). and locking cams (Figure 1). NOTE: Cam Locks on Base Panel face away from Back Panel. ST-E ST-F ST-A ST-H ST-A Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 3 Foot Bracket(Figure 2). Then insert 4 Medium Bolts(K) and 6 Wood Screws(N). Also, insert 4 Glides(Q) into Foot Bracket(ST-D). Figure 2 ST-D ST-D ST-H STEP 8 : Insert 8 Shelf Pins(M) and place 2 Shelves(ST-B). Place Cam Caps(P) over cam locks. Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 4 Hinges(T) interlocks with the Hinge Bracket(U) opening. Tighten screw(EA) to secure door. Note: The screw EB is an adjustment for the door position. Turn right to adjust door to center and left to adjust toward the side. Any problems or questions call Regency Office Furniture at 1-866-816-9822...
- Page 5 OPTIONAL STEP B: Connect Tower to Low Credenza by inserting Long Bolt(J) through Credenza Top Hole and into the Center Support(ST-C). NOTE: THIS CONNECTION WILL PERMANENTLY DISFIGURE THE LOW CREDENZA TOP! Credenza Top Hole Low Credenza Top Any problems or questions call Regency Office Furniture at 1-866-816-9822...
Need help?
Do you have a question about the ONHD3033 and is the answer not in the manual?
Questions and answers