Moldex 7000 Series Instructions
Probed cartridge kit for quantitative fit testing with portacount
Hide thumbs
Also See for 7000 Series:
- Instruction manual (44 pages) ,
- Quick start manual (4 pages) ,
- User instruction manual (2 pages)
Advertisement
7000/7800/9000 SERIES RESPIRATORS
#7006 PROBED CARTRIDGE KIT INSTRUCTIONS
FOR QUANTITATIVE FIT TESTING WITH
PORTACOUNT
®
WARNING:
The #7006 Probed Cartridge is for use in quantitative fit testing together with a TSI Portacount or equivalent fit
test instrument. The cartridge does not contain filter media and therefore provides no protection.
In accordance with OSHA 29 CFR 1910.134 (f) a quantitative fit test must be performed before a respirator is
assigned to a wearer. The Moldex #7000/7800 half masks and/or #9000 full face respirators can be
quantitatively fit tested using the TSI Portacount, or similar, fit tester together with the appropriate Moldex
#7006 Probed Cartridge as labeled.
Caution: Always place the #7006 Probed Cartridge on the user's left side of respirator. There are two different
probed cartridges per kit. ONLY use the shorter tubed cartridge with the #7000/7800. ONLY use the longer
tubed cartridge for the #9000. Read cartridge labels for the correct probed cartridge for either the #7000/7800
or the #9000. Failure to follow these directions will result in incorrect fit test readings.
MOLDEX-METRIC, INC.
10111 W. Jefferson Blvd., Culver City, CA 90232
Tel: +1 (800) 421-0668 or +1 (310) 837-6500
Fax: +1 (310) 837-9563
Email: sales@moldex.com www.moldex.com
Moldex, Ideas that wear well and the PVC-Free logo are
registered trademarks. U.S. Patents Pending.
7006-710 REV C
03/18
APPENDIX A
CANADIAN CUSTOMER SERVICE
Tel: +1 (800) 421-0668, Ext. 517 Fax: +1 (310) 837-9563
BRAZIL – MOLDEX-METRIC LTDA
®
Av Ipiranga, 104, 22º Andar Sala 01
Sao Paulo, SP Brazil
Tel/Fax: +55 (11) 26 59 21 08
moldexbrazil@moldex.com
AUSTRALIA – MOLDEX-METRIC, INC.
Unit 30/14-16 Stanton Road, Seven Hills, NSW 2147
Tel: +61 (2) 9838 7588 Fax: +61 (2) 9838 7544
Email:
moldexaustralia@moldex.com www.moldex.com
NEW ZEALAND – MOLDEX-METRIC, INC.
3 Spence Road, Henderson, Auckland, NZ
Tel: +64 (9) 837 8247 Fax: +64 (9) 837 8248
Email:
moldexnz@moldex.com www.moldex.com
MOLDEX TECHNICAL SERVICE DEPARTMENT:
+1 (800) 421-0668 or +1 (310) 837-6500, ext. 512/550
Advertisement
Table of Contents
Related Manuals for Moldex 7000 Series
Summary of Contents for Moldex 7000 Series
- Page 1 In accordance with OSHA 29 CFR 1910.134 (f) a quantitative fit test must be performed before a respirator is assigned to a wearer. The Moldex #7000/7800 half masks and/or #9000 full face respirators can be quantitatively fit tested using the TSI Portacount, or similar, fit tester together with the appropriate Moldex #7006 Probed Cartridge as labeled.
- Page 2 CONTENTS: 2 #7006 Probed Cartridges (one for #7000/7800 and one for #9000) 1 Pair #7940P100 Filter Disks 1 Pair #7920 Filter Disk Piggyback Adapters INSTRUCTIONS: Before conducting a quantitative fit test, the #7000/7800 or #9000 Series Respirator Facepiece must be assembled with the appropriate #7006 probed cartridge and the #7940P100 Filter Disk together with a #7920 Piggyback Adapter on one side, and a #7940P100 Filter Disk on the other side.
- Page 3 Moldex products proved to be defectively manufactured. Except as provid- ed above, Moldex shall not be liable or responsible for any loss, damage, or liability, direct, indirect, inciden- tal, special, or consequential, arising out of sale, use, or misuse, or the inability to use products by the user.
Need help?
Do you have a question about the 7000 Series and is the answer not in the manual?
Questions and answers