Related Manuals for Renesas EZ-0008
Summary of Contents for Renesas EZ-0008
- Page 1 Quick Start Guide EZ-0008 Lighting Communication Master Evaluation Board ZUD-CE-09-0018-E Data Published March 2009 © NEC Electronics Corporation 1/16...
- Page 2 The information in this document is current as of March, 2009. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country.
- Page 3 Safety Precautions This document explains matters to be noted for safe use of Lighting Communication Master Evaluation Board. Be sure to read this document before using Lighting Communication Master Evaluation Board. • Be sure to observe all dangers, warnings, cautions, and other instructions contained herein when using this evaluation board.
- Page 4 Warnings Warning Do not use this board in the purpose except the evaluation of MCU. This board does not take safety measures or anti-EMI measures required for lighting equipment. Do not heat the board or expose it to fire, and do not short the terminals. Doing so may cause product failure, generation of heat, fire, or rupture.
- Page 5 Cautions Caution Do not use or store this board in any of the following locations. Environments with copious water, humidity, steam, dust, fumes, etc. Environments where static electricity or electrical noise is readily generated. Such influences can lead to electric shock or product failure. In case liquid enters the board, cut the power supply, and consult your dealer or NEC Electronics sales representative.
- Page 6 CONTENTS OVERVIEW ……………………………………………………… CHAPTER 1 SPECTIFICATION ……………………………………………… CHAPTER 2 OPERATION ……………………………………………………… 11 CHAPTER 3 APPENDIX A REVISION HISTORY …………………………………………… 15 ZUD-CE-09-0018-E 6/16...
-
Page 7: Chapter 1 Overview
Evaluation board(EZ-0007) This board Host PC Lighting Communication Master Evaluation Board 78K0/IB2 HBLED Evaluation (EZ-0008) Board (EZ-0005) 1.1 Feature ・ USB power supply. 5V supply voltage 15V for DALI communication generated by switching regulator ・ 3 kinds of operation mode supported... -
Page 8: Chapter 2 Spectification
2. Specification This chapter described the specification of Lighting Communication Master Evaluation Board. 2.1 Appearance of the board The following figure shows the appearance of Lighting Communication Master Evaluation Board. Figure 2. Appearance of Lighting Communication Master Evaluation Board USB Connector Connector for DMX512 Connector for DALI communication... - Page 9 2.2 Detail specification Board name : EZ-DLMST-002 Power supply : DC5[V] Microcontroller : UPD78F0503AD Connector : ML-800-S1V-nP (n=2, 3) Recommend communication cable: refer to figure 3 Figure 3. Recommend communication cable specification 2.3 Power supply Lighting Communication Master Evaluation Board uses USB cable for power supply as well as communication.
- Page 10 2.4 Switch setting Table1. Switch setting Description IR remote control code selecting switch. “CH1”: Send custom code 0x0000＋data code 0x5AA5 “CH2”: Send custom code 0x0000＋data code 0xDA25 Push button. Send remote control signal by IR diode DMX512 mode selecting switch “DMX”: Enable DMX512 communication operation “Wireless”: Disable DMX512 communication operation Operation mode switch...
-
Page 11: Chapter 3 Operation
3.1 Preparation 3.1.1 Driver installation Install the driver when connecting the Lighting Communication Master Evaluation Board (EZ-0008) to the PC by using a USB cable for the first time. ① Download driver from following URL. www.necel.com/micro/en/solution/lighting/download.html ② When connecting this board to PC by using USB cable,”Found New Hardware Wizard”... - Page 12 3.2.1 Operate with DMX512 interface ① Confirm SW4 is set to “RUN“side and SW3 is set to “DMX” side. ② Connect the lighting communication master evaluation board (EZ-0008) with DMX512 slave board or your own evaluation board supporting DMX512 protocol via interface J1.
- Page 13 3.2.2 Operate with DALI interface ① Confirm SW4 is set to “RUN” side. ② Connect the lighting communication master evaluation board (EZ-0008) with DALI slave board or your own evaluation board supporting DALI protocol via interface J4. Figure 6 . DALI interface (J4) None polarity ③...
- Page 14 3.2.3 Operate with IR remote control interface ① Confirm SW4 is set to “RUN” side. ② Set SW1 to the expected channel. The output code is based on NEC IR remote control protocol CH1: Send custom code 0x0000＋data code 0x5AA5 CH2: Send custom code 0x0000＋data code 0xDA25 ③...
-
Page 15: Appendix A Revision History
Appendix A Revision History Revision Modified Points Page Rev.1.0 First edition ZUD-CE-09-0018-E 15/16... - Page 16 For further information, please contact: NEC Electronics Corporation 1753, Shimonumabe, Nakahara-ku, Kawasaki, Kanagawa 211-8668, Japan Tel: +81-44-435-111 http://www.necel.com/ [Technical Support] Multipurpose Microcomputer System Division, NEC Electronics Tel: +81-44-435-9452 Data Published March 2009 ZUD-CE-09-0018-E 16/16...
Need help?
Do you have a question about the EZ-0008 and is the answer not in the manual?
Questions and answers